RETUSIOR MKL2023 Ceiling Fan with Light User Guide

RETUSIOR MKL2023 Ceiling Fan with Light

Packing List

Note: Some parts may be assembled in the package.

Installation kit

Note: Some extra hardware may be included. The quantity listed above is the number required for installation.

Safety Rules

1. Be sure the power to the wires you are working on is disconnected, either the fuse is removed or the circuit breaker is turned off. Turning the power off using the light switch is not sufficient to prevent electrical shock.
2. A qualified licensed electrician is required for the installation.
3. The outlet box and support structure must be securely mounted and capable of reliably/supporting a minimum of 50 pounds. Use only UL (cUL for Canadian Installation) listed mounting boxes marked “FOR FAN SUPPORT”.
4. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor.
5. Do not operate the reversing switch while fan blades are in motion (if applicable). The fan must be turned off and the blades stopped before reversing the blade direction.
6. Do not place any objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other items, be cautious when work- ing around or cleaning the fan.
8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened soft cloth will be suitable for the cleaning.
9. After marking electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor on one side of the outlet box.
10. Electrical diagrams are reference only, different fan lights may have different light shades and bulbs.
11. Use only our replacement parts. This equipment has been tested and found to comply with the limits for a class B digital device, under part 15 of the FCC Rules. These limits are to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used per the instructions may cause harmful interference to radio communications.

Warning:

• To reduce the risk of personal injury, use only the two steel screws and washers provided with the outlet box for mounting to the outlet box.
• Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and need to be replaced, consult a qualified electrician if in doubt.
• To reduce the risk of fire, electric shock, or personal injury, mount the fan to the outlet box marked “acceptable for fan support”.
• To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.

Installation Preparation

Tools You Need

If mounting to a support structure, you will also need the optional tools.

What to Expect with Your Installation

Installation Step 1 (Mount the Bracket)

• Loosen screws from the canopy (don’t take off), take out the bracket from the canopy.
• With Outlet Box: Fix the bracket onto the outlet box with screws from the outlet box, and fix the crossbar of the bracket onto the ceiling with 4 wood screws (optional).
• Without Outlet Box: Fix the crossbar onto the solid wood structure with 4 wood screws.

Installation Step 2 (Connect the wires)

1. Hang the fixture onto the bracket with the “S” hook provided.
2. Connect wires from the fixture to the wires from the outlet box with wire nuts, ground wire (green, green/yellow, or bare copper) to ground wire, neutral wire (white or blue) to the neutral wire, hot wire (black or brown) to the hot wire. Wrap the connection with electrical tape.
3. Take away the “S” hook.

Installation Step 3 (Fix the Canopy)

1. Fix the bracket screws onto the bracket but not tighten them.
2. Align the “L” slots from the canopy to the screws on the bracket, and rotate the canopy to lock it onto the bracket.
3. Tighten the screws.

Remote Control Instructions

• NOTE: Please insert 2 batteries before using. AAA 1.5V battery x 2pcs (not included)
• PAIR CODE: Remote signal pairing. If the remote control loses the signal of the fan, press and hold this button at the very beginning after it’s powered on from the wall switch. After the fan flashes or beeps, it’s paired successfully.

Trouble Shooting

1. The fan doesn’t work
   • Make sure the fixture is connected to an ON/OFF wall switch, not a dimmer switch.
   • Check the remote control battery (not included in this package).
   • Check the circuit breaker to ensure the power is on.
   • Turn off the power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.
2. Lights Do Not Light Up / Flicker / Noisy Operation
   • Make sure the fixture is connected to an ON/OFF wall switch, not a dimmer switch.
   • Check your power and switch to make sure it’s powered on.
3. Noisy Operation
   • Re-tighten all screws on the bracket.
   • Check to see if any of the blades are cracked. If so, replace the blades.
4. Remote does not work
   • Make sure the battery is installed correctly.
   • Pair the remote control again (See page 9).
   • Install 2 new batteries.

Clean And Care

• To clean, wipe the fixture with a soft cloth. Spray from chemical cleaners can discolor the finish of the fixture.
• Do not use scouring pads, powders, steel wool, or abrasive paper to clean this fixture.

Ordering Parts

• Keep this manual for future reference, and in case replacement parts are needed.
• Available parts can be ordered from the place of purchase. Use exact wording from diagrams when ordering parts.

Contact Information

• IF YOU HAVE ANY QUESTIONS PLEASE FEEL FREE TO CONTACT US.
• WE WILL SERVE YOU 7*24 HOURS

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>