Golden Lighting 6808-6SF Raphia Ellie 6 Light Semi Flush Drum Ceiling Fixture Instruction Manual
- August 8, 2024
- GOLDEN LIGHTING
Table of Contents
Golden Lighting 6808-6SF Raphia Ellie 6 Light Semi-Flush Drum Ceiling
Fixture
Product Information
Specifications
- Model: 6808-6/6808-6SF
- Model Variants: 6808-6SF MBG-WR
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of island. Fixtures should hang at least 30 inches above the countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
Installation Tips
Install the lights with dimmers that allow you to control the level of light output at any given moment for optimal lighting conditions.
Layered Lighting
To achieve the best lighting in your space, layer your lighting with fixtures like sconces, flush mounts, and pendants to provide both task and ambient lighting.
Product Maintenance
Browse our site for coordinating lights and expert lighting advice to maintain function and style in your lighting setup.
FAQ
- How do I identify the fixture’s wires?
- The fixture wires typically include hot, neutral, and ground wires. The ground wire is usually copper, bare metal, green, or transparent inner thread. Ensure to match these with the corresponding house wires for proper installation.
- What should I do if I need replacement parts?
- Contact the place of purchase for customer service to arrange for replacement parts.
Product Information
- Pendants & Linear Pendants Above a Kitchen Island
- Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.
- Pendants & Chandeliers Above a Dining Room Table
- Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
- Pendants and Chandeliers in Open Areas
- The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice.
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
Assembly Instructions
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. THIS FIXTURE CAN BE INSTALLED AS A CHANDELIER OR AS A SEMI- FLUSH. FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 1. From the parts bag remove the mounting strap assembly (A). One end of nipple (F) should be attached to mounting strap (A) with hex nut (D) in place. The other end should have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. 2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar should fit snugly onto the canopy loop. Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached. FOR SEMI- FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED (2): 1. Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & D) should be attached to mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to the mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. Use hex nuts (C) to hold mounting screws (A) in place.
ASSEMBLING THE FIXTURE
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1):
Measure to determine the correct number of chain links needed for proper
hanging height. If necessary, use a pair of pliers to open and remove any
excess chain. Attach one chain connector (K) to each end of chain (J). Attach
one end of the chain/chain connector to top loop (L). Feed the fixture wires
from the fixture body through post (N). Pull the wires until taut. Thread
washer (M) onto post (N). Thread top loop (L) onto post (N). Attach the
remaining end of the chain/chain connector to canopy loop (H). Close chain
connectors (K) to secure. Feed fixture wires from nipple (N) through top loop
(L), the chain (J) (every three links or so), canopy loop collar (I), canopy
loop (H), and canopy (G). Pull the wires until taut. Gently slide canopy loop
collar (I) and canopy (G) down onto the chain/wires. Trim the wires to the
desired length plus 8 to 10 inches. FOR SEMI-FLUSH INSTALLATION REFER TO THE
DIAGRAM LABELED (2): 2. Feed the fixture wires from the fixture body through
post (H). Pull the wires until taut. Feed fixture wires from post (H) into
canopy (F) until the wires come out of the top of canopy (F). Thread canopy
(F) onto post (H) and fasten it. Pull the wires until taut. Trim the wires to
the desired length plus 8 to 10 inches. 3. Have an assistant support the
fixture’s weight. Attach mounting strap (B) to the junction box using mounting
screws (D) and a screwdriver. Tighten the screws securely. Pull the house
wires through the center of the mounting strap (B).
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 5. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy (G). Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy (G) in place. Slide candle sleeves (P) over sockets. Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test your fixture. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED (2): 5. Push canopy (F) up to the ceiling and tightly thread nuts (G) onto the exposed threads of mounting screws (A) on mounting strap (B). Slide candle sleeves (J) over sockets. Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test your fixture.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>