dji Matrice 350 RTK Industrial Grade Mapping Inspection Drone User Guide
- October 30, 2023
- DJi
Table of Contents
dji Matrice 350 RTK Industrial Grade Mapping Inspection Drone
Aircraft
The DJI™ MATRICE™ 350 RTK (M350 RTK) is a powerful industrial aircraft platform with an advanced flight controller system, six directional sensing and positioning systems, and a night view FPV camera. The M350 RTK supports DJI CSM Radar and is compatible with DJI DGC2.0 connector gimbals, up to three independent gimbals, and several SDK expansion ports. High accuracy Surveying and Mapping is available when used with the DJI ZENMUSE™ L 1 /P1. Al Spot Check and Pin Point can be used with the DJI Zenmuse H20 series.
- FPV Camera
- Infrared Sensing System
- Vision System
- DJI Gimbal Connector v2.0 (DGC2.0)
- Frame Arms
- Motors
- Propellers
- Front LEDs
- Transmission Antennas
- Landing Gear
- Gimbal Camera
- Aircraft Status Indicators
- GNSS Antennas
- Intelligent Flight Battery
- Power Button/Indicator
- Assistant Port
- E-Port
- Payload Port
Remote Controller
The DJI RC Plus remote controller features 03 Enterprise, the latest version of DJl’s signature OCUSYNC™ image transmission technology, and can transmit a live HD view from the camera of the aircraft to display on the touchscreen. The remote controller comes with a wide range of functional buttons as well as customizable buttons, which can easily control the aircraft and operate the camera.
The built-in 7.02-inch high-bright screen boasts a resolution of 1920×1200 pixels. The Android operating system comes with a variety of functions, such as GNSS, Wi-Fi, and Bluetooth. The remote controller has a maximum operating time of 3 hours and 18 minutes with the internal battery and up to 6 hours when used with an external WB37 Intelligent Battery.
- External Antennas
- Touchscreen
- Aircraft Authority Button
- Control Sticks
- Internal Wi-Fi Antennas
- Bade/Function Button
- Return to Home (RTH) Button
- Status LED
- Battery Level LEDs
- Internal GNSS Antennas
- Power Button
- SD Button
- Flight Pause Button
- Record Button
- Flight Mode Switch
- Internal Antennas
- microSD Card Slot
- USB-A Port
- HDMI Port
- USB-C Port
- Focus/Shutter Button
- Battery Release Button
- Battery Compartment
- Rear Cover Release Button
Using M350 RTK
Charging the Batteries
- Power on the BS65 Intelligent Battery Station: connect the battery station to a power outlet using the AC power cable, and press the power button once to power on the battery station.
- Activating and Charging the Remote Controller: connect the battery station and the remote controller USB-C ports using a USB-C to USB-C cable. The battery level LEDs start to flash to Indicate that the Internal battery ls activated and charging started.
- Charging the TB65 Intelligent Flight Batteries and WB37 Intelligent Battery: insert the batteries Into the battery ports to start charging.
For the TB65 batteries, set the charging mode to Storage, Ready-to-Fly, or Standard as desired.
Refer to the instructions in the battery station or BS65 Intelligent Battery Station User Guide for more information.
Preparing the Remote Controller
Mounting the WB37 Intelligent Battery Push the rear cover release button to
open the rear cover 1. Insert the WB37 battery Into the battery compartment
and push forward until it clicks firmly in place 2 · To remove the WB37
battery, press and hold the battery release button.
Checking the Battery Level
Press once on the power button to check the battery level of the Internal
battery when powered off.
Powering On/Off
Press and then press and hold to power on/off the remote controller. The
remote controller needs to be activated before using it for the first time.
Follow the prompts to activate.
Adjusting the Antennas
Lift and adjust the antennas. The strength of the remote controller signal
is affected by the position of the antennas.
The remote controller cannot be powered on before activating the internal battery. The internal battery of the remote controller can also be activated after mounting the WB37 battery.
Preparing the Aircraft
Installing the Landing Gear
Insert the landing gear after aligning the red marks with the mounting position, slide the gear lock to tile end of the land Ing gear, then rotate It untll tile red mart Is: In sync with tile alignment mark.
Unfolding the Aircraft
- Unfold the front frame arms and tllen tile rear frame arms.
- Lock the frame arms and unfold tile propellers.
Installing the Gimbal Camera
Installing the Intelligent Flight Battery
Insert a pair of batteries and lock the battery release toggle.
Check battery level: press the battery level button once.
Power on/off: press and then press and hold the power button to power on/off
the aircraft.
Flight
Power on the remote controller and aircraft, and then launch DJI PILOT™ 2.
-
Activate the aircraft in DJI Pilot 2 before using it for the first time. Follow the on-screen instructions for activation. An internet connection is required.
-
The remote controller is already linked to the aircraft when it is purchased together as part of a combo.
Otherwise, follow the on-screen instructions to link the remote controller and the aircraft after activation. -
Make sure to finish Pre-Flight Checklist before takeoff.
Pre-Flight Checklist
- Make sure the remote controller and the aircraft batteries are fully charged, the TB65 batteries are installed firmly, and the battery release toggle is locked.
- Make sure the propellers are securely mounted and not damaged or deformed, there are no foreign objects in or on the motors or propellers, the propeller blades and arms are unfolded, and the frame arms are locked.
- Make sure the lenses of the vision system, cameras, the glass of the infrared sensors, and the auxiliary lights are clean and not blocked in any way.
- Make sure the remote controller antennas are adjusted to the proper position.
- Place the aircraft on open and flat ground. Make sure there are no obstacles, buildings, or trees nearby and that the aircraft is 5 m away from the pilot. The pilot should be facing the rear of the aircraft.
- To ensure flight safety, enter the camera view of DJI Pilot 2 and check the parameters on the Preflight Check.
- Divide the airspace for flight when multiple aircraft are operating simultaneously in order to avoid collision mid-air.
Manual Takeoff/Landing
- Start/stop motors: perform Combination Stick Command and hold for two seconds.
- Takeoff: slowly push the left control stick (Mode 2) up to take off.
- Landing: slowly push the left control stick (Mode 2) down until the aircraft lands. Hold for three seconds to stop the motors.
Control Stick Mode
The default control stick mode is Mode 2. The left control stick controls the altitude and heading of the aircraft while the right control stick controls the forward, backward, and sideward movements.
Specifications
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>