SINJI Health Bracelet User Manual
- June 7, 2024
- SINJI
Table of Contents
HEALTH BRACELET
Manual
1. CONTENTS OF THE PACKAGE
• Sinji Smart Health Bracelet
• Manual
2. TECHNICAL SPECIFICATIONS
- Model: Sinji Smart Health Bracelet
- Band length: 240mm
- Weight: 20g
- Clasp material: Aluminium Alloy
- Strap material: TPU/Silicone
- Waterproof grade: IP67
- Display: 0.87 inch OLED
- Bluetooth: Ver. 4.0
- Battery: Lythium Polymer
Disclaimer:
This Sinji Smart heart rate band is not a medical instrument. Please consult
your general practitioner, trainer or specialist to monitor any abnormal
results.
3. INSTRUCTIONS FOR USE
3.1 How to wear the watch
The Sinji Smart Health bracelet is best-worn right behind the wrist, in such a
way that it cannot move around too much. The sensors on the back of the band
should be in direct contact with skin for measurements to be possible.
3.2 Charging the Sinji Smart Health bracelet
Please make sure the band is fully charged before connecting. This ensures the
connection to be made as smoothly as possible. To charge the band, disconnect
the center unit for the band as such:
Connect the center unit to any USB port to start charging. Charging should be
completed after 2~3 hours.
3.3 Downloading the APP
Please search for “Flagfit” in the Android or iOS store, and download the app.
After downloading, please install the app. When prompted, please allow the app
access to your phonebook, pictures, and music.
3.4 Operating the Sinji Smart Health bracelet
Turn on the Sinji Smart heart rate band by pressing the main key for 5
seconds, the screen will light up when ready. The length of press required to
turn on the band can be changed in the Flagfit application. Turn the band back
off by pressing the main key for 5 seconds, selecting “off”, and pressing the
main key for 5 seconds once again.
3.5 Pairing the Sinji Smart heart rate band to your phone
- Make sure the band is fully charged before first use
- Make sure Bluetooth is enabled on your mobile device
- Press the main key of the watch for a few seconds to turn the band on.
- Go to the Flagfit app
- Pull down on the white portion of the screen. Your mobile device will start searching for any nearby Smart bands Please note: The band can only be connected to one device at a time. Before pairing to your phone, make sure it is disconnected from all other devices.
Once the Bluetooth connection has been established, the smart band will automatically connect when turned on, and in range of your mobile device.
4. MAIN FUNCTIONS
4.1 Personal information and exercise goal
Setting your personal information and exercise goal when entering the Flagfit
app for the first time ensures measurements are as personalized as possible.
You can edit your personal information and exercise goals at any time by going
into Settings->Personal settings
4.2 Notifications
You can receive notifications on your smart band if:
1. Notifications are enabled in your mobile device’s settings.
2. The band and your mobile device remain in close proximity of each other
The band will vibrate when you receive a new notification on your mobile
device.
- Incoming calls: The band will vibrate and display caller ID
- Message: The band will vibrate and display contact name
- Alarm Clock: Up to 3 alarms can be set, band will vibrate
- Sedentary: The band will vibrate if no motion is detected for set period
4.3 Miscellaneous settings
- Other notifications: Allow for different apps to send notifications to the Sinji Smart heart rate band.
- Loss prevention: If turned on, your mobile device will display an alert if your Sinji Smart Health bracelet is moving away from your mobile device.
- Find Band: If selected in the Flagfit app, the band will start vibrating to allow for easy retrieval.
- Shake and photograph: When activate it will allow the Sinji Smart Health Bracelet to take a picture when the camera app is opened for easy selfies.
- Firmware upgrade: Searches for newer versions of the firmware for the Sinji Smart Health bracelet.
- Factory date reset: resets the band to factory values. Erases all personal data from the band, and from the app.
4.4 Display options
By pressing the main button on the Sinji Smart Health bracelet, you can scroll
through the different display options.
1. Clock interface: the main interface of the band. Shows a Bluetooth icon
with a cross if the band is not connected to your mobile device, and a
bluetooth icon with two waves if a connection is made.
2. Steps: Shows steps taken since last reset.
3. Distance: Shows distance walked based on steps and height.
4. Heart Rate: Shows approximate current heart-rate. You can start testing
heart rate by long pressing the main key in this display mode.
5. SAFETY INSTRUCTIONS
- Keep the product away from sharp objects.
- Don’t place heavy objects on top of the product.
- Don’t use any (chemical or organic) liquids with the product.
- Keep the product away from heat sources.
6. CLEANING
Clean the product with a dry cloth. Don’t use any chemical liquids or oil!
7. NOTES
- Please try to keep the app connected to your bracelet.
- Please allow for several seconds of delay for data transfer between phone and watch.
- If you need to replace the watch with the same model, the app will ask you to keep the previous data: click “sync” to keep the data, click “no” to remove all previous data. Please choose carefully!
- For first-time use, the bracelet needs personal data for modeling and may appear inaccurate until the watch has been in continuous use for 24 Hours, after which the data will be more and more accurate.
8. PROBLEMS AND SOLUTIONS
1. I can’t find the device when pairing.
• Please make sure the distance between your phone and the watch is no more
than 0.5m. After pairing the Bluetooth communication range is within 10m.
• Please make sure the device is not low on battery. If there is still a
problem after the watch is charged, please contact support.
2. How do I update the device?
• Make sure the device is connected with the app. hoose “Firmware Update”, the
process will search for available updates. Please wait a few minutes for the
update to be finished.
3. The data does not seem to be accurate.
• The watch will take at least 24 hours to get somewhat accurate data from
your body condition. After the first day it will get more accurate every day!
Made in China www.sinjiproducts.com © 2019 Sinji. All rights reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>