Golden Lighting 6808-6SF Ellie Light Wide Drum Chandelier Instruction Manual
- August 8, 2024
- GOLDEN LIGHTING
Table of Contents
Golden Lighting 6808-6SF Ellie Light Wide Drum Chandelier
Specifications
- Model Numbers: 6808-6/6808-6SF, 6808-6 MBG-WR
- Maximum Power: Not specified
- Materials: Not specified
- Wire Types: Fixture Wires (Hot, Neutral, Ground), House Wires (Hot, Neutral, Ground)
Product Usage Instructions
- Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of the island. Fixtures should hang at least 30 inches above the countertop.
- Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table.
- The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
- Attach mounting strap (B) to the junction box using mounting screws (D) and a screwdriver. Tighten the screws securely.
- Pull the house wires through the center of the mounting strap (B).
- Connect the wires following the provided wire types.
- Finish the installation as per the provided instructions.
FAQ
- How do I choose the right pendant light for my space?
- To choose the right pendant light, consider the size of the space and the purpose of the lighting. Ensure that the pendant’s size and style complement the room’s decor and that it provides adequate illumination for its intended use.
- Can I install dimmers with these lights?
- Yes, you can install dimmers to control the level of light output. Make sure to follow the dimmer compatibility guidelines provided with the lights for safe and optimal use.
Dimension
Pendants & Linear Pendants Above a Kitchen Island
- Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of the island. Fixtures should hang at least 30″ above the countertop.
Pendants & Chandeliers Above a Dining Room Table
- Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas
- The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
- Great lighting can add value and enhance the look of your home.
- To ensure the best lighting in your space, remember to layer your lighting.
- This ensures that your space will have both task and ambient lighting.
- Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic.
- Install the lights with dimmers that allow you to control the level of light output at any given moment.
- Get function and style! Browse our site for coordinating lights and expert lighting advice.
How to Identify the Fixture’s Wires
Assembly Instructions
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT
- All installation work should be done by an accredited professional.
- Shut off the power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove the old fixture from the wall, including the old mounting strap. THIS FIXTURE CAN BE INSTALLED AS A CHANDELIER OR AS A SEMI-FLUSH. FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 1. From the parts bag remove the mounting strap assembly (A). One end of the nipple (F) should be attached to the mounting strap (A) with hex nut (D) in place. The other end should have a canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. 2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar should fit snugly onto the canopy loop. Remove the canopy (G) and adjust the height of the nipple (F) and canopy loop (H) until the desired height is reached. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED (2): 1. Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & D) should be attached to the mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to the mounting strap (B). Line up the holes in the canopy (F) with the holes in the mounting strap (B) and insert mounting screws (A) into the mounting strap (B) so that mounting screws (A) protrude through the holes in the canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. Use hex nuts (C) to hold mounting screws (A) in place.
ASSEMBLING THE FIXTURE
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 3. Measure to determine the correct number of chain links needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach one chain connector (K) to each end of a chain (J). Attach one end of the chain/chain connector to top loop (L). Feed the fixture wires from the fixture body through post (N). Pull the wires until taut. Thread washer (M) onto post (N). Thread top loop (L) onto post (N). Attach the remaining end of the chain/chain connector to the canopy loop (H). Close chain connectors (K) to secure. Feed fixture wires from nipple (N) through the top loop (L), the chain (J) (every three links or so), canopy loop collar (I), canopy loop (H), and canopy (G). Pull the wires until taut. Gently slide canopy loop collar (I) and canopy (G) down onto the chain/wires. Trim the wires to the desired length plus 8 to 10 inches. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED (2): 2. Feed the fixture wires from the fixture body through post (H). Pull the wires until taut. Feed fixture wires from post (H) into the canopy (F) until the wires come out of the top of the canopy (F). Thread canopy (F) onto post (H) and fasten it. Pull the wires until taut. Trim the wires to the desired length plus 8 to 10 inches. 3. Have an assistant support the fixture’s weight. Attach mounting strap (B) to the junction box using mounting screws (D) and a screwdriver. Tighten the screws securely. Pull the house wires through the center of the mounting strap (B).
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting strap
and wrap the fixture’s ground wire around the ground screw. Use a screwdriver
to tighten the top of the ground screw (E) onto the wires and into the
mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 5. Push canopy
(G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy
(G). Tightly thread canopy loop collar (I) onto canopy loop (H) to secure
canopy (G) in place. Slide candle sleeves (P) over sockets. Install light
bulbs (not included) under the fixture’s specifications. Do not exceed the
maximum recommended wattage. Your installation is now complete. Turn on the
power and test your fixture. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM
LABELED (2): 5. Push canopy (F) up to the ceiling and tightly thread nuts (G)
onto the exposed threads of mounting screws (A) on the mounting strap (B).
Slide candle sleeves (J) over sockets. Install light bulbs (not included)
under the fixture’s specifications. Do not exceed the maximum recommended
wattage. Your installation is now complete. Turn on the power and test your
fixture.
Get help, quick tips, and explore curated content
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>