Golden Lighting 6808-4SF Ellie Light Wide Drum Chandelier Instruction Manual
- August 7, 2024
- GOLDEN LIGHTING
Table of Contents
Instruction Manual
6808-4SF Ellie Light Wide Drum Chandelier
Thank You for Choosing Us for Your Lighting Needs! Pendants & Linear
Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop. Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table. Pendants and Chandeliers in Open
Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
Assembly Instructions
How to Identify the Fixture’s Wires Hot: Smooth, Black, or Transparent
with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement
parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. THIS FIXTURE CAN BE INSTALLED AS A CHANDELIER OR AS A SEMI-
FLUSH. FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 1. From
the parts bag remove the mounting strap assembly (A). One end of nipple (F)
should be attached to mounting strap (A) with hex nut (D) in place. The other
end should have canopy loop (H) attached. Attach mounting strap (A) to the
junction box using mounting screws (B) and a screwdriver. Tighten securely. 2.
Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the
mounted canopy loop to test the height.
Approximately half of the canopy loop’s exterior threads should be exposed,
and the canopy loop collar should fit snugly onto the canopy loop. Remove
canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the
desired height is reached. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM
LABELED (2): 1. Mounting strap (B) contains several threaded holes. Two sets
of mounting screws (A & D) should be attached to mounting strap (B). You may
need to tighten nuts (C) that hold mounting screws (A) in place. If the screws
are not attached, please hold canopy (F) up to mounting strap (B). Line up the
holes in canopy (F) with the holes in mounting strap (B) and insert mounting
screws (A) into mounting strap (B) so that mounting screws (A) protrude
through the holes in canopy (F). Mounting screws (A) are long, so please test
the canopy against the mounting strap to see how far you should insert the
screws. 2. Attach mounting strap (B) to the junction box using mounting screws
(D) and a screwdriver. Tighten the screws securely. Pull the house wires
through the center of mounting strap (B).
ASSEMBLING THE FIXTURE
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 3. Measure to
determine the correct number of chain links needed for proper hanging height.
If necessary, use a pair of pliers to open and remove any excess chain. Attach
one chain connector (K) to each end of chain (J). Attach one end of the
chain/chain connector to top loop (L). Feed the fixture wires from the fixture
body through post (N). Pull the wires until taut. Thread washer (M) onto post
(N). Thread top loop (L) onto post (N). Attach the remaining end of the
chain/chain connector to canopy loop (H). Close chain connectors (K) to
secure. Feed fixture wires from nipple (N) through top loop (L), the chain (J)
(every three links or so), canopy loop collar (I), canopy loop (H), and canopy
(G). Pull the wires until taut. Gently slide canopy loop collar (I) and canopy
(G) down onto the chain/wires. Trim the wires to the desired length plus 8 to
10 inches. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED (2): 3.
Feed the fixture wires from the fixture body through post (H). Pull the wires
until taut. Feed fixture wires from post (H) into canopy (F) until the wires
come out of the top of canopy (F). Thread canopy (F) onto post (H) and fasten
it. Pull the wires until taut. Trim the wires to the desired length plus
6808-4/6808-4SF 8 to 10 inches.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting strap
and wrap the fixture’s ground wire around the ground screw. Use a screwdriver
to tighten the top of ground screw (E) onto the wires and into the mounting
bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED (1): 5. Push canopy
(G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy
(G). Tightly thread canopy loop collar (I) onto canopy loop (H) to secure
canopy (G) in place. Slide candle sleeves (P) over sockets.
Install light bulbs (not included) in accordance with the fixture’s
specifications.
Do not exceed the maximum recommended wattage. Your installation is now
complete. Turn on the power and test your fixture. FOR SEMI-FLUSH INSTALLATION
REFER TO THE DIAGRAM LABELED (2): 5. Push canopy (F) up to the ceiling and
tightly thread nuts (G) onto the exposed threads of mounting screws (A) on
mounting strap (B). Slide candle sleeves (J) over sockets. Install light bulbs
(not included) in accordance with the fixture’s specifications. Do not exceed
the maximum recommended wattage. Your installation is now complete. Turn on
the power and test your fixture.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>