Wi-Tek WI-PCMS310GF, WI-PCMS328GF Cloud L2 plus Managed PoE Switch Installation Guide

Wi-Tek WI-PCMS310GF, WI-PCMS328GF Cloud L2 plus Managed PoE Switch

Specifications:

• 24 X 1000 Mbps PoE+ Ports
• 8 X 1000 Mbps PoE+ Ports
• 2 X Gigabit SFP Slots
• 100-240V AC Power Input
• Cloud L2+ Managed PoE Switch

Product Usage Instructions

Packing Content:

The package includes:

• Cloud L2+ Managed PoE Switch x 1
• Quick Installation Guide x 1
• Serial Line x 1
• Power Cord x 1
• Mounting Accessories (hook x 2, mats x 4, screw x 8)

Appearance Overview:

The product features:

• Reset Button and LED lights
• 8*10/100/1000Mbps PoE+ Ports
• 1*Console Port
• 2*1000Mbps SFP Slots

Installation:

To install the PoE Switch:

1. Connect the WAN port of the Gateway to the Internet.
2. Connect one LAN port of the Gateway to the PoE Switch.
3. Connect the PC to the Switch.
4. Ensure PC and Gateway are in the same subnet.

Configuration:

To configure the device:

1. Power on the device.
2. Connect Internet to WAN port of Gateway.
3. Connect LAN port of Gateway to PoE Switch.
4. Connect PC to Switch.

Logging In:

To log in to the device:

1. Launch a web browser and enter the IP address in the address bar.
2. Use default username and password ‘admin’ to log in.

Frequently Asked Questions (FAQ):

Q: How can I restore the device to factory default settings?
A: Hold the Reset button for more than 5 seconds to restore factory default settings.

Q: What should I do if the LED indicators show abnormality?
A: If LED indicators are off or blinking abnormally, check for power connection issues or system abnormalities.

Packing Content

Appearance Overview

WI-PCMS310GF

Front panel

Back panel

LED indicator and botton

LED indicators & button  Description

SYS| Blinking: The Device system is operating normally

Off: Device system or power connection abnormality

PWR| On: The device power on is normal

Off: The device is power off or failed

PoE| On: Equipment connected, normal power supply

Off: Port not for terminal equipment power supply

Link

| On: Port connected Blinking: Data transmission

Off: Port disconnected

Reset| Hold for >5 sec. to restore factory default

WI-PCMS328GF

Front panel

Back panel

LED indicator and botton

LED indicators & button  Description

SYS| Blinking: The Device system is operating normally

Off: Device system or power connection abnormality

PWR| On: The device power on is normal

Off: The device is power off or failed

PoE| On: Equipment connected, normal power supply

Off: Port not for terminal equipment power supply

Link

| On: Port connected Blinking: Data transmission

Off: Port disconnected

Reset| Hold for >5 sec. to restore factory default

Installation

Desktop Installation

Rack-Mount Installation

Configuration

First, the device is powered on, the Internet is connected to the WAN port of the Gateway,the other one LAN port of the Gateway is connected to the PoE Switch, then the PC is connected to the Switch. Ensure that the PC and the Gateway are in the same subnet.

Log in to the switch locally
Let the Switch obtain an IP address and then check the DHCP server to see which IP address was assigned.
The Switch is set to DHCP by default, so it will try to obtain an IP address automatically.
If that fails, then it will use the default fallback IP address, 192.168.0.1

To log in, follow these steps:

1. Launch your web browser. you type the appropriate IP address in the address bar
2. The login screen will appear. The default username and password are both admin

Use the console cable to access the switch

Connection Diagram:

Step 1 Download a PuTTY software

Step 2 Use the Console cable to connect the computer and the switch as shown in the above figure

Step 3 Set the com port number of the Console line and the baud rate of the switch in the software (steps as shown in the figure below).

Notice:

Step 2 is your computer recognizes the COM number of the Console line

Step 3 is the baud rate of the exchange (the baud rate of the switch is 9600)

Note: If the switch device is not connected to the cloud platform, the management account password is admin by default. If it is connected to the cloud platform for management, please go to the cloud platform to check the password. The account is admin, and the password is the WEB password you set when creating t he project.

Use Telnet to log in to the CLI mode of the switch
Connection Diagram:

Step 1 Configure the IP address of the computer and the IP address of the same segment as the switch

Step 2 Open the cmd window of the computer

Step 3 Enter Telnet followed by the management IP address of the switch (for example, if the management IP address of the switch is 192.168.0.1, enter Telnet 192.168.0.1)

Note: If the switch device is not connected to the cloud platform, the management account password is admin by default. If it is connected to the cloud platform for management, please go to the cloud platform to check the password.

The account is admin, and the password is the WEB password you set when creating the project.

Cloud login switch configuration

1. Log in to the cloud management interface
   (No account, you need to register an account to log in，The URL is：http://cloud2.wireless-tek.com）

2. Enter the cloud binding switch
   (explain:The switch must be connected to the Internet to bind successfully)
   Please enter the device serial number to bind a device to the current group, device can be off when binding.
   (Explanation: The 17-digit SN code of the switch is shown on the sticker on the back of the switch as shown in the figure below)

3. After binding, you can use the Switch in the Tunnel option in the cloud management, and then choose to use EWEB or TELNET to enter the switch.
   (After entering the switch, you can configure it based on your own needs)

Warranty Card

Username|
---|---
Address|
Telephone No.|
Purchase Shop|
Purchase Address|
Product Model No.|
Purchase Time|
Serial No.|
Dealer Signature|

• If the product defects within three months after purchase, we will provide you with a new product of the same model.
• If the product defects within the three-year warranty period, we will provide professional maintenance service.
• Proof of purchase and a complete product serial number are required to receive any services guaranteed as part of the limited warranty.
• Any other defects that are not caused by workmanship or product quality, such as natural disasters, water damage, extreme thermal or environmental conditions, sticker damaged, warranty card loss will disqualify the product from limited warranty.

Wireless-Tek Technology Limited

Address: Building 3, Units 1801-1807, 1812,Huaqiang Era Plaza, Tangwei Community,Fuhai Street, Bao’an District, Shenzhen City,Guangdong Province, China.
Website:www.wireless-tek.com

Tel:86-0755-32811290
Email: sales@wireless-tek.com
Technical Support:tech@wireless-tek.com

References

• Test and Measurement Equipment | Tektronix
• Wireless-Tek Technology Limited.
• Wireless-Tek Technology Limited.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>