KVM SWITCHS PKS0802A10 4-Port Dual Monitor DP KVM Switch User Manual

4-Port Dual Monitor DP KVM Switch
USER MANUAL
ENJOY THE VIVID WORLD
DP•Dual

Features:

• Using only 1 set of keyboard, mouse and 2 monitors to control 2 computers
• Support 2 monitors to display the desktop of 1 computer or to display 2 desktops at the same time.
• Support Unix/Windows/Debian/Ubuntu/Fedora/Mac OS X/ Raspbian/Ubuntu for Raspberry Pi and other Linux basic systems
• Support resolution up to 3840*2160©60HZ Support hot plug, disconnect, or connect devices to the KVM at any time without turning off the PC
• Support front panel button, keyboard hotkeys, IR remote control, and RS232 to control KVM
• Available to use keyboard and mouse without any delay after switching input sources
• With an extra USB 2.0 port, it is possible to connect a bar code scanner, USB hard device, or another USB device
• Support keyboard and mouse pass-through mode to improve KVM compatibility
• Support auto switch to monitor computers in a specified time interval
• Support DCCI

Packing List

1 Dual Monitor DP KVM Switch
1 IR remote control
1 IR Receiver cable
1 DC 12V power adapter
1 3 Pins Connector(For RS232)
2 Rack-eras 1 AUX Cable
1 User manual

Panel Description:

to select the input sources by sending RS232 commands
3| Ext. IR| For extended IR receiver cable input
4| L/R audio output| Analog audio output, connect to the speaker
5| Standard USB 2.0 port| Connect to USB 2.0 devices, printers, USB drives
6| DCCI port| Used for product cascading to realize simultaneous display of 4 monitors
ID| Name| Description
---|---|---
| Keyboard and mouse input| Connect to keyboard and mouse
8| DP output ports| Connect to DP displays
9| PC 4 Input| DP input A/B: Connect to the two outputs of the same computer

USB: Connect to a computer by USB Type A to Type B cable

10| PC 3 Input| DP input A/B: Connect to the two outputs of the same computer

USB: Connect to a computer by USB Type A to Type B cable

11| PC 2 Input| DP input A/B: Connect to the two outputs of the same computer

USB: Connect to a computer by USB Type A to Type B cable

12| PC 1 Input| DP input A/B : Connect to the two outputs of the same computer

USB: Connect to the computer by USB Type A to Type B cable

13| Auto-scan time interval settings| [MIN]: Press [MIN] to loop between 0-59 minutes

[SEC]: Press [SEC] to loop between 0-59 seconds

[Set]: After setting minutes and seconds, press the button [Set] to enter the final scan time interval setting

scanning mode
16| IR receiver| Receive IR remote signal
17| Keypad

| [1-4]: Press button[1]-[4] to directly select input 1-4

[Output A]: Keyboard and mouse focus on the desktop of output A in the display mode 2

[Output B]: Keyboard and mouse focus on the desktop of output B in the display mode 2

[Output A]+[1-4]: After pressing [Output A], then press [1-4] to switch input sources of output A

[Output B]+[1-4]: After pressing [Output B], then press [1-4] to switch input sources of output B

[Close]: Press this button to turn on or off the LED display and monitor

[Scan]: Press this button to start or stop automatically scanning between input1 to input8. The interval time can be set by [Set], [MIN], [SEC] as described above

18| Power switch| Turn on or turn off the power supply

Connection Diagram :

Step 1: Connect the two outputs of the PC1 to the Input A and Input B of the KVM PC1 inputs. Connect the USB of the PC to the USB of the KVM PC1 inputs with USB type A to B cable Note: Both Input A and Input B should be connected to the same computer. If connect only one of them, then the dual monitor function would not work properly.
Step 2: Connect the keyboard, mouse, and monitors to the specified ports.

Step 3: Connect speakers, USB devices, Ext. IR and RS232 to the KVM.

Step 4 : Directly connect the DCCI port of the first KVM switch according to the above steps, in order to realize simultaneous display of 4 monitors

Cascade Diagram

Note: The slave only connects to monitors and computers. Computers need to connect 4 DP cables simultaneously.

Step 5: Turn on the power switch to start the Dual Monitor KVM.

How To Use:

1. Set up the connection according to the connection diagram.
2. After all the PCs are started in step 1, then you can control the Dual Monitor KVM by keyboard hot keys, IR control, or the front-panel key, the specific control methods are as follows:

How to use keyboard hotkeys
Press the [Alt] key twice to change the actively selected computer in display mode 2
Note: Display mode 2 means one monitor display one PC.
Select pod by port number
Turn off auto-switching mode
Enable or disable the buzzer sound
Turn on auto-switching mode
Note: The default auto-switching time interval is 6 seconds, you are able to change this value by following hotkey commands:
Increase or decrease the auto-switching time interval
Note:1 second per step, the time is up to 250 seconds.

Turn on or off the keyboard and mouse pass-through mode
Note: For the best compatibility, it is better to turn on the keyboard and mouse pass-through mode. In this mode, the keyboard and mouse are dynamically mapped to the computer, so you are able to use a special keyboard and mouse with multimedia keys or other customized keys.
How to identify whether the KVM is in keyboard and mouse pass through mode?
Turn on the KVM, press [Scroll Lock] + [Scroll Lock] + [F3], if the buzzer beeps twice, the KVM is in keyboard and mouse pass-through mode. And beeping once means in keyboard and mouse emulation mode.
HOW TO CHANGE THE HOTKEYS COMBINATION:
There are two kinds of trigger hotkeys in this product, the default is the [Scroll Lock] key, and the alternative is the [Right-Ctrl] key. if the [Scroll Lock] key has been used for other functions, you can switch the hotkey to [Right-Ctrl] by
Method 1:
Press and keep holding the [Set] button on the front panel until you hear the buzzer is beeping, then restart KVM.
Method 2:
Press [Scroll Lock]+[Scroll Lock]+[F1], and you will switch the control hotkey to [Right Ctrl].
Vice verse, press [Right Ctrl]+[Right Ctrl]+[F1], and you will switch the control hotkey to [Scroll Lock].

IR Remote Control :

Note:

1. For the safety request by some express companies, the remote control is not equipped battery by default.
2. The unspecified buttons above are non-functional.

RS232 Commands (HEX):

(0x00-0x38) ss means seconds (0x00-0x38)

Note: the minimum time interval is 5s.

Warranty Information:

We warrant this product as free of defects in material and workmanship for a period of one (1) year from the date of shipment.
If during the period of warranty this product proves defective under normal use, we will repair or replace this product, provided that this product has not been subjected to mechanical, electrical, or other abuse or modifications. If it fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for six (6) months from the day of reshipment to the buyer.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>