GE APPLIANCES GFD65ESSVWW Stackable Steam Cycle Smart Electric Dryer User Guide

GE® 7.8 cu. ft. Capacity Front Load Electric Dryer with Steam GFD65ESSVWW / GFD65ESPVDS

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)

ELECTRIC DRYER RATING

120V/240V| 5600W, 25A, 60Hz
120V/208V| 4300W, 23A, 60Hz

EXHAUST OPTIONS : 4-way via rear, left, right, and bottom.
(The right, left, and bottom venting options require Side Vent Kit: GFA28DSVN)
CIRCUIT REQUIREMENTS : An individual, properly grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36″ of service cord entry and accessible when dryer is mounted in position.
INSTALLATION INFORMATION : For complete information, see installation instructions packed with your dryer.*With leveling legs retracted: 39-3/4″ (101 cm).
With leveling legs fully extended: 40-5/8″ (103.1 cm).

SPECIAL INSTALLATION REQUIREMENTS:

STACKED INSTALLATION:
Brackets for stacking dryer over washer are not included with the dryer. Order part no. GFA28KITN.
ALCOVE OR CLOSET INSTALLATION:
If your dryer is approved for installation in an alcove or closet, it will be label on the dryer back.
The dryer MUST be exhausted to the outside.
Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0″ all sides and top.
Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed.
If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
The dryer MUST be exhausted to the outdoors.
The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALLATIONS:
Minimum clearances to combustible surfaces 0″ all sides and top.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.

*For improved performance, a 1/2″ clearance is suggested on each side.
**Accessories sold separately.

WEIGHT

• Carton weight 142 lbs.
• Product weight 132 lbs.

DRYER ACCESSORIES**

WARRANTY

DRYER EXHAUSTING INFORMATION –METAL DUCT ONLY

For complete information, see installation instructions packed with your dryer.

DUCTING MATERIALS: For best performance, this dryer should be vented with 4″ diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special  installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.
A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please  see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.

EXHAUST LENGTH CALCULATION:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4″ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.
   A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow.
   A turn over 45° should be treated as a 90° elbow.

CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust  into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be  located at least 12″ above the ground or any other obstruction with the opening pointed down.

FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.

FEATURES AND BENEFITS

Powersteam – Refresh small loads and dewrinkle larger loads with the power of steam.
Built-in WiFi – Start, stop and monitor your laundry from anywhere while receiving real-time notifications and updates.
Quick Dry – Quickly dries items and small loads for families on the go.
Reduce Static – Prevents static cling with a gentle mist near the end of the cycle.
Sanitize Cycle – Sterilize clothing with elevated temperatures designed to kill common household bacteria.
Wrinkle Care – Prevents wrinkles by extending the tumble without heat.
Damp Alert – Signals when delicate clothes reach the ideal dampness level for ironing or final air drying.
Vent Sensor – Provides alerts when a restriction is detected in your dryer vent. 4 Way Venting – Easy-to-change venting options provide the ultimate installation flexibility to fit in your home.
Shallow Depth – Never compromise on convenience with this 32″ shallow depth unit that easily fits into tight spaces like an alcove or closet, making it a suitable solution for homes of any size.
Reversible Door – Easily reverse your washer and dryer door for superior installation flexibility.
My Settings – Store preferred dry cycle settings for later use, maximize time and alleviate adjusting cycle preferences with every load.
Model GFD65ESSVWW – White
Model GFD65ESPVDS – Carbon Graphite

For answers to your Monogram, Café™ , GE Profile™ or GE Appliances product questions,
visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000. Specification Revised 6/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>