Wi-Tek WI-PS302GF-I Unmanaged Industrial Hardened PoE Switch Instruction Manual
- June 10, 2024
- Wi-Tek
Table of Contents
Wi-Tek WI-PS302GF-I Unmanaged Industrial Hardened PoE Switch Instruction
Manual
Package Content
1 x Switch
1 x Installation Guide
Interface and LED Indicator
WI-PS302GF-I
Interfaces
Ethernet Port| 110/100/1000 Base-T PoE+ + RJ-45
Fiber Port| 11000 Base-X SFP slot
DIP Switch Mode
1. Fiber Watchdog| Monitor the fiber connection status, and if no data is
transmitted, the port will restart automatically.
2. PoE Watchdog| All PoE ports enable PoE watchdog function, which can detect
and reboot the offline compliant PoE powered devices.
3. Extend Mode| The transmission distance of PoE port can be up to 250m, but
the rate is limited to 10Mbps.
4. 60W PoE Mode| Enable this function, the PoE port will output 60W PoE
power. Disable this function, the PoE port output 802.3at 30W PoE power.
LED Indicators
PW (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
V1/V2/V3(Input power indicator)| Off: No power supplyOn: Power is supplying
via V1/V2/V3 DC connector
Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
EX Indicator| Off: Extend mode is disabled. On: Extend mode is enabled.
SFP Indicator| Off: ports link down Green On: ports link up Blinking:
data on TX/RX
WI-PS306GF-I
Interfaces
Ethernet Port| 410/100/1000 Base-T PoE RJ-45 port Ports 1-2 :
24V Passive / 48V 802.3 af/at PoE Ports 3-4: 802.3 af/at/bt 60W
Fiber Port| 21000 Base-X SFP
DIP Switch Mode
1. FWD| Monitor the fiber connection status, and if no data is transmitted,
the port will restart automatically.
2. PWD| All PoE ports enable PoE watchdog function, which can detect and
reboot the offline compliant PoE powered devices.
3. Extend| The transmission distance of PoE port can be up to 250m, but the
rate is limited to 10Mbps.
4. VLAN| All downlink ports are isolated from each other, but can communicate
with uplink ports.
LED Indicators
PWR (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
P1/P2(Input power indicator)| Off: No power supplyOn: Power is supplying via
P1/P2 DC connector
Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
PoE Indicator| Off: PoE not working On: PoE working
**** 5/6 (SFP Indicator)| Off: ports link down On: ports link up
Blinking: data on TX/RX
PoE Max| On: PoE power full load
WI-PS310GF-I
Interfaces
PoE Port| 810/100/1000 Base-T PoE RJ-45 port Ports 1-2: 24V
Passive / 48V 802.3 af/at PoE Ports 3-4: 802.3 af/at/bt 60WPorts 5-8: 802.3
af/at PoE
Uplink Port| 21000 Combo Base-X SFP
DIP Switch Mode
1. 24/48| PoE output voltage adjustment DIP switch for port 1.
2. 24/48| PoE output voltage adjustment DIP switch for port 2.
3. Watchdog| All PoE ports enable PoE watchdog function, which can detect and
reboot the offline compliant PoE powered devices.
4. Extend| The transmission distance of PoE port can be up to 250m, but the
rate is limited to 10Mbps.
4. VLAN| The transmission distance of PoE port can be up to 250m, but the
rate is limited to 10Mbps.
LED Indicators
PWR (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
P1/P2(Input power indicator)| Off: No power supplyOn: Power is supplying via
P1/P2 DC connector
Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
PoE Indicator| Off: PoE not working On: PoE working
**** 9/10 (SFP Indicator)| Off: ports link down On: ports link up
Blinking: data on TX/RX
PoE Max| On: PoE power full load
WI-PS305G-I-DC
Interfaces
PoE Port| 410/100/1000 Base-T PoE RJ-45 port Ports 1-4: 802.3 af/at PoE
Uplink Port| 110/100/1000 Base-T RJ-45 port
DIP Switch Mode
1. PoE Watchdog| PoE watchdog, all PoE ports enable PoE watchdog function,
which can detect and reboot the offline compliant PoE powered devices.
2. Port VLAN| All downlink ports are isolated from each other, but can
communicate with uplink ports.
3. EX_1-2| The transmission distance of port 1-2 can be up to 250m, but the
rate is limited to 10Mbps.
4. EX_1-4| The transmission distance of port 1-4 can be up to 250m, but the
rate is limited to 10Mbps.
LED Indicators
PWR (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
P1/P2(Input power indicator)| Off: No power supplyOn: Power is supplying via
V1/V2 DC connector
**** Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
PoE Indicator| Off: PoE not working On: PoE working
WI-PS206-I
Interfaces
Ethernet Port| 410/100 Base-TX PoE RJ-45 ports Ports 1 : 802.3 af/at/bt
90WPorts 2-4: 802.3 af/at PoE
Fiber Port| 210/100 Base-TX RJ-45 ports
DIP Switch Mode
1. PoE Watchdog| PoE watchdog, all PoE ports enable PoE watchdog function,
which can detect and reboot the offline compliant PoE powered devices.
2. EX_1-2| The transmission distance of port 1-2 can be up to 250m, but the
rate is limited to 10Mbps.
3. EX_1-4| The transmission distance of port 1-4 can be up to 250m, but the
rate is limited to 10Mbps.
4. VLAN| All downlink ports are isolated from each other, but can communicate
with uplink ports.
LED Indicators
PW (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
V1/V2/V3(Input power indicator)| Off: No power supplyOn: Power is supplying
via V1/V2/V3 DC connector
Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
PoE Indicator| Off: PoE not working On: PoE working
VLAN| Off: VLAN mode is disable. On: VLAN mode is enable.
Extend| Off: Extend mode is disable. On: Extend mode is enable.
WI-PS208-I
Interfaces
* PoE Port| 810/100 Base-TX PoE RJ-45 ports Ports 1-2 : 802.3 af/at/bt
90WPorts 3-8: 802.3 af/at PoE
DIP Switch Mode
1.PoE Watchdog| PoE watchdog, all PoE ports enable PoE watchdog function,
which can detect and reboot the offline compliant PoE powered devices.
2. EX_1-4| The transmission distance of port 1-4 can be up to 250m, but the
rate is limited to 10Mbps.
3. EX_1-6| The transmission distance of port 1-6 can be up to 250m, but the
rate is limited to 10Mbps.
4. VLAN| All downlink ports are isolated from each other, but can communicate
with uplink ports.
LED Indicators
PW (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
V1/V2/V3(Input power indicator)| Off: No power supplyOn: Power is supplying
via V1/V2/V3 DC connector
** Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
PoE Indicator| Off: PoE not working On: PoE working
VLAN| Off: VLAN mode is disable. On: VLAN mode is enable.
Extend| Off: Extend mode is disable. On: Extend mode is enable.
WI-PS206GF-I
Interfaces
PoE Port| 410/100 Base-TX PoE RJ-45 ports Ports 1-4: 802.3 af/at PoE
Uplink Port| 11000 Base-X SFP slot 1*10/100/1000 Base-T RJ-45 port
DIP Switch Mode
1. 250m| The transmission distance of port 1-4 can be up to 250m, but the
rate is limited to 10Mbps.
2. VLAN| All downlink ports are isolated from each other, but can communicate
with uplink ports.
3. Watchdog| PoE watchdog, all PoE ports enable PoE watchdog function, which
can detect and reboot the offline compliant PoE powered devices.
4. Priority| Port PoE power supply priorities are in descending order.
LED Indicators
PWR (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
PoE Indicator| Off: PoE not working On: PoE working
6 (SFP Indicator)| Off: ports link down On: ports link up
Blinking: data on TX/RX
WI-PS212GF-I
Interfaces
PoE Port| 810/100 Base-TX PoE RJ-45 ports Ports 1-8: 802.3 af/at PoE
Uplink Port| 21000 Base-X SFP slot 2*10/100/1000 Base-T RJ-45 port
DIP Switch Mode
1.250m| The transmission distance of port 1-4 can be up to 250m, but the rate
is limited to 10Mbps.
2.VLAN| All downlink ports are isolated from each other, but can communicate
with uplink ports.
3.Watchdog| PoE watchdog, all PoE ports enable PoE watchdog function, which
can detect and reboot the offline compliant PoE powered devices.
4.Priority| Port PoE power supply priorities are in descending order.
LED Indicators
PWR (Power indicator)| Off: the device is power off or failed On: the device
power on is normal
Link Indicator| Off: ports link down On: ports link up Blinking:
data on TX/RX
PoE Indicator| Off: PoE not working On: PoE working
11/12 (SFP Indicator)| Off: ports link down On: ports link up
Blinking: data on TX/RX
DIN-rail Installation
Please follow the steps below.
Step 1: Install the switch to the DIN rail. Accessories
| Null
DC Power Cable Connection
This switch can work with 37~57V DC power, the DC power connection processes are as follows.
- Before installation, ensure that the device is disconnected from the power supply.
- Connect one end of the protective grounding cable to the grounding screw on the side panel of the device, and the other end is well grounded nearby.
- Connect the positive and negative wires of DC power separately to the “+” and “-” power terminal of 48~57V power 1 or 37~57V power 2 on the switch as following figure, using screw driver to screw stably.
- The redundant power can be both connected with the DC power, so that one power supply can still work in case the other one fails.
- Turn on the DC power, and check if power supply indicator of power 1 or power 2 turns on, whic
Note: For WI-PS206GF-I and WI-PS212GF-I, V1 and V2 DC interface cannot be connected to the power supply at the same time.
Warranty Card
Username|
---|---
Address|
Telephone No.|
Purchase Shop|
Purchase Address|
Product Model No.|
Purchase Time|
Serial No.|
Dealer Signature|
- If the product defects within three months after purchase, we will provide you a new product of the same model.
- If the product defects within the three-year warranty period, we will provide the professional maintenance service.
- Proof of purchase and a complete product serial number are required to receive any services guaranteed as part of the limited warranty.
- Any other defects that are not caused by workmanship or product quality, such as
natural disaster, water damage, extreme thermal or environmental conditions. sticker damaged, warranty card losing will disqualify the product from limited warranty.
Wireless-Tek Technology Limited
Address: Room 402 4F, BiaoFan Technology Building, Bao’An
Avenue, FuYong Town, Bao’An district, ShenZhen
Website:www.wireless-tek.com
Tel:86-0755-32811290
Email:sales@wireless-tek.com
Technical Support:tech@wireless-tek.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>