VIVO STAND-TV75E Black TV Floor Stand Instruction Manual

: August 5, 2024
: Vivo

Table of Contents

VIVO STAND-TV75E Black TV Floor Stand
Product Information
Product Usage Instructions
Package Contents
Included Hardware & Tools
Security Cable Kit
Tools Needed
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIVO STAND-TV75E Black TV Floor Stand

Product Information

Brand: VIVO
Model: STAND-TV75E
Weight Capacity: TV – 77lbs (35kg), Shelf – 11lbs (5kg)

Product Usage Instructions

Package Contents

Base (B) x1
Support Plate (C) x1

Assembly Steps

Step 1: Assemble the Base
Attach Pole (A) to Base (B) using M8x40mm Screws (S-C) and 5mm Allen Wrench (T-B). Remove the protective film from Round Pads (G) and place them on the bottom of the Base.
Step 2: Adjust Height and Attach Support Plate
Adjust the preinstalled Height Adjustment Bracket on Pole (A) to your desired height. Secure Support Plate (C) to the front of the Height Adjustment Bracket using M8x20mm Screws (S-B), Large M8 Washers (S-D), and 5mm Allen Wrench (T-B).
Step 3: Attach VESA Brackets to TV
Attach VESA Brackets (D) to the back of your TV using the provided Mounting Hardware, ensuring correct orientation with the locking screw positioned towards the bottom of the TV. Tighten with a Phillips screwdriver.

Tools Needed

Phillips Screwdriver
Power Drill

FAQ

Q: What should I do if I exceed the weight capacity?
A: Do not exceed the weight capacity as it may result in serious injury. If you need a stand for heavier devices, consider purchasing a model with a higher weight capacity.
Q: How do I contact customer support?
A: You can contact our dedicated support team by phone at 309-278-5303 during office hours or visit our website for live chat or email options.

Assembly Video & Product Info
www.vivo-us.com/products/stand-tv75e.

CAUTION!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo- us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
  THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: DO NOT INSTALL INTO DRYWALL ALONE
VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo- us.com, email at help@vivo-us.com, or call us at 309-278-5303.

We’re Here for You
Open Monday – Friday 7:00 am – 7:00 pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Give us a Call: 309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
Chat Us: www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
Email Us: help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr

Package Contents

Included Hardware & Tools

Security Cable Kit

Tools Needed

Weight Capacity:

ASSEMBLY STEPS

STEP 1

Attach Pole (A) to Base (B) using M8x40mm Screws (S-C) and 5mm Allen Wrench (T-B).
Remove the protective film from Round Pads (G) and place them on the bottom of the Base, as shown below.

The Pole should be installed with a Height Adjustment Bracket facing the front of the Base.

STEP 2
The position of the preinstalled Height Adjustment Bracket on Pole (A) can be adjusted to your desired height. To adjust, begin by removing the preinstalled screws using the 5mm Allen Wrench (T-B), adjust the Bracket, and then reinstall the screws in your desired position.

Secure Support Plate (C) to the front of the Height Adjustment Bracket on Pole (A) using M8x20mm Screws (S-B), Large M8 Washers (S-D), and 5mm Allen Wrench (T-B).

STEP 3
Attach VESA Brackets (D) to the back of your TV using the assorted Mounting Hardware shown below, making note of the combinations for Upper and Lower VESA Slots. Tighten with a Phillips screwdriver. To help orient the VESA Brackets ensure the locking screw is positioned towards the bottom of the TV.

Upper VESA Slot:
Choose the combination that best suits your TV.
Lower VESA Slot:
Choose the combination that best suits your TV.

STEP 4
Hang the TV with VESA Brackets (D) onto the Support Plate (C). Secure the Locking Screws on VESA Brackets using a Phillips screwdriver.

STEP 5
Remove the protective film from Square Pad (I) and apply it the the inside corner of Shelf Bracket (F).

Attach Shelf Bracket (F) to Pole (A) at one of three heights using M8x20mm Screws (S-B) and a 5mm Allen Wrench (T-B).

STEP 6
Place Shelf (E) onto Shelf Bracket (F) and secure using M6x10mm Screws (S-A) and a Phillips screwdriver.

STEP 7
Press Cable Clips (H) into the slots on the back of Pole (A) and route cables through while placing.

STEP 8
To adjust the TV tilt, use a 4mm Allen Wrench (T-A) to loosen and adjust the Tilt Screws on the side of VESA Brackets (D).

STEP 9a – Wood Stud
To install the Security Cable Kit, use a stud finder to hold the Wall Bracket (P-C) up to the wall and mark the hole position along a stud between 39.4”-51.2” (1000 mm-1300 mm) off of the floor.

Drill a 1.6” (40mm) deep hole using a ⅛” (3.5mm) drill bit. Secure Wall Bracket (P-C) to the wall using ST4.8x38mm Screw (P-E) and a Phillips screwdriver.

STEP 10a – Wood Stud

Route the Security Cable (P-A) through the Wall Bracket (P-E) and both Security Cable Clips (P-B) previously installed with VESA Brackets (D).
Loosen the screw on Cable Lock (P-D) using a Phillips screwdriver. Slide Cable Locks onto the ends of the Security Cable and tighten the screw using a Phillips screwdriver to secure.

STEP 9b – Concrete/Brick
Hold the Wall Bracket (P-C) up to the wall and mark the hole position between 39.4”-51.2” (1000 mm-1300 mm) off of the floor.

Drill a 1.6” (40mm) deep hole using a 9/32” (7mm) drill bit. Secure Wall Bracket (P-C) to the wall using ST4.8x38mm Screw (P-E), Concrete Anchor (P-F), and a Phillips screwdriver.

STEP 10b – Concrete/Brick

Route the Security Cable (P-A) through the Wall Bracket (P-C) and both Security Cable Clips (P-B) previously installed with VESA Brackets (D).
Loosen the screw on Cable Lock (P-D) using a Phillips screwdriver. Slide Cable Locks onto the ends of the Security Cable and tighten the screw using a Phillips screwdriver to secure.

Need Help? Get In Touch
Monday-Friday from 7:00 am-7:00 pm CST