5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual

: June 6, 2024
: Ring

Table of Contents

START
LOCATION
SETUP
TESTING
MOUNTING
POWER
FINISH AND TEST
SETTINGS
WARRANTY
Z-WAVE
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

5AT3T4 Outdoor Siren for Ring Alarm Instruction Manual

START

Power Sources
The Outdoor Siren can be used with one or more power sources. This guide will show you how to install using the included D Batteries. Visit ring.com /outdoor-siren to learn about other power sources and installation tips.

Included

3 x D Batteries

Sold Seperately

Ring Solar Panel & Quick Release Battery Pack
- Keeps the battery pack charged
Hardwired
- Advanced electrical skills required
- Supports 9-28V, 12W DC power input and 0.2~2.5mm2 wire
Hardwired with Plug-in Adapter (2nd gen.)

Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device.

LOCATION

The Outdoor Siren should be mounted on the outside of your home, in a location with:

Visibility, so the Outdoor Siren can be seen by anyone passing your home.
Safe access, so you can change the batteries safely. If using a ladder, make sure there is solid ground below.
Close to a power source, if using backup power.

SETUP

Start by opening the Ring app and tap Set up a Device, then tap Security, Sirens, and Outdoor Siren.
Follow the directions in the app.

To scan the QR code, you’ll need to loosen the security screw on the bottom of the mounting bracket, then slide the bracket o¬ of the Outdoor Siren (the screw stays in the bracket).

Pull the battery tab when prompted by the app.

TESTING

TESTING INDUCTION

Press the Test button inside the battery compartment on the back of the Outdoor Siren. The LED lights on the front will flash — this may take up to 30 seconds.

Green means the test is successful.
Red means the test failed. Try moving a Range Extender between the Outdoor Siren and the alarm system, or find a new wall or area for mounting, then test again.

MOUNTING

MOUNTING INDUCTION

Hold the mounting bracket at the mounting location and level it using the spirit level.
Mark your holes using the mounting bracket as a guide.
Drill holes using a 6mm drill bit.
Adjust the tamper arm screw to ensure that the arm makes contact with the mounting surface.

POWER

POWER INDUCTION

Visit ring.com/outdoor-siren to learn how to use the Outdoor Siren with other power sources.

D Cell Batteries
If you need to replace the batteries, match the + and – icons.
Ring Quick Release Battery
Carefully insert Quick Release Battery Pack, starting with the pin side first.
Ring Solar Panel connection
Remove the rubber stopper from the DC Jack, then connect the Solar Panel.
Hardwired Terminals /
Ring Plug-in Adapter (2nd Generation) Supports 9–28V, 12W DC power input and 0.2~2.5mm2 wire.

Do not apply DC power above or below 9–28V, 12W.
Do not apply AC power.
Do not use wire gauge above or below 0.2~2.5mm2

To install

WARNING: Electrical shock hazard. Always turn off the power before you begin working with electrical wiring.
Loosen the Outdoor Siren’s positive and negative terminals.
Open the rubber cover and thread the wires through.
Connect the positive and negative wires and securely re-tighten the terminals.

SAFETY NOTE: We recommend that you consult a licensed professional electrician if you are not experienced with hardwiring projects. Please use extra caution when using a ladder to minimize the risk of fall.

FINISH AND TEST

When you finish connecting your power sources, replace the back cover, then attach the Outdoor Siren to the mounting bracket. Tighten the security screw on the bottom of the bracket. Follow the directions in the app to test the Outdoor Siren.

WARNING: Loud Siren and Strobe lights.

SETTINGS

Using the Ring app, you can adjust the Outdoor Siren LED and audio settings to meet your preferences and comply with local laws. Please check your local laws about the volume and duration of sirens. Visit ring.com/outdoor- siren for more details.