VIVO DESK-V100EBY Electric Single Motor Desk Frame Memory Controller Instruction Manual
- October 30, 2023
- Vivo
Table of Contents
VIVO DESK-V100EBY Electric Single Motor Desk Frame Memory Controller
The DESK-V100EBY Controller is an electronic device designed to control the height of a desk. It allows the user to adjust the desk height to their desired position, providing comfort and convenience during work hours. The controller comes with safety instructions that must be followed to avoid damage or serious injury.
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products /desk-v100eby
GET IN TOUCH
Monday-Friday from 7:00am-7:00pm CST
[email protected]
www.vivo-us.com Chat live with an agent!
309-278-5303
SAFETY INSTRUCTIONS
WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND
ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
- DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
- DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
- NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED.
OPERATING CONTROL PANEL
OPERATING INSTRUCTIONS:
Press the up arrow, the desk will automatically raise to the highest position.
Pressing the down arrow will automatically lower the desk to the lowest
position.
Memory Mode
To store a certain height in the controller’s memory, press the 1 button for
more than three seconds. “S-1” will be displayed, indicating that the current
height has been saved to the 1 button sucessfully. Repeat the process using
buttons 2,3, and 4.
Switch the Display from Centimeter to Inch
The preset measurement shown on the display is cm. If you would like to change
cm to inch, press and hold buttons 1 and 4 for more than three seconds.
Reset Mode
- If the height of the desk is incorrect, press the down arrow until the desk moves to the fully lowered position. Press and hold the down arrow again for at least three seconds and release. “rSt” will be displayed.
- If the system displays “Er1”, press and hold the down arrow for more than three seconds and release. “rSt” will be displayed.
Collision Avoidance Settings
Press and hold the down and up buttons together for more than three seconds to
enter the Collision Avoidance Settings Mode. Use the arrow buttons to adjust
the sensitivity level. Once the sensitivity has been selected, press the up
and down arrows again for more than three seconds to save the setting.
Collision Avoidance Sensitivity Levels: 0-9
- 0: Turn off collision avoidance.
- 1-9: Level 1 is the lowest sensitivy and level 9 is the highest.
Setting the Minimum/Maximum Height
- Press the 1 and 2 buttons at the same time for more than three seconds to set the current height as the maximum.
- “Hon” will be displayed.
- To cancel the maximum height, repeat the process.
- “HoF” will be displayed.
- When the maximum height is reached during operation, the panel will display “HI” notifying the upper limit has been reached.
- Press the 3 and 4 buttons at the same time for more than three seconds to set the current height as the minimum.
- “Lon” will be displayed.
- To cancel the minimum height, repeat the process.
- “LoF” will be displayed.
- When the minimum height is reached during operation, the panel will display “Lo” notifying the lower limit has been reached.
TROUBLESHOOTING
- ER1 Press the and hold the down arrow to perform a reset.
- Hot The desk is overheated. Allow the desk to rest for more than 18 minutes before operating.
CAUTION!
Failure to follow these instructions may result in property damage and/or
personal injury.
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
- 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
- www.vivo-us.com Chat live with an agent! AVG. RESOLUTION TIME (within office hrs): < 15 M
- [email protected] AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Electric Single Motor Desk Frame with Memory Controller – VIVO - desk solutions, screen mounting, and more