Kessil A80 LED Illuminator Owner’s Manual
- June 4, 2024
- Kessil
Table of Contents
A80
OWNER’S MANUAL LED ILLUMINATOR
PARTS DIAGRAM
A. Power Cord
B. Spectrum Tuning Dial
C. 0-10V Controller Ports
D. Heat Sink Fin
E. Lens
F. Intensity Dial
G. DC Power Supply
PRODUCT SPECIFICATIONS
Illuminator
Power Consumption| 15W maximum
Input Voltage| 24VDC
Listed Power Supply
Input| 100-240VAC, 50-60Hz
Output| 24VDC, maximum 1A
INSTALLATION GUIDE
- Remove contents from package.
- Hang the A80 1 to 2 ft. above the plants/tank.
- Connect Power Cord (A) to the specified DC Power Supply (G).
- Plug the power supply into an outlet with the correct specifications (see product specifications for more information).
- Using the A80’s Intensity Tuning Dial (F) and Spectrum Tuning Dial (B), set the light to the desired setting. A80 Tuna Blue tunes from 10,000K Actinic. A80 Tuna Sun tunes from 6,000K – 9,000K.
- The ports beneath the dials can be connected to an external 0~10V controller. Please consult your controller’s owner’s manual for more information.
SAFETY INSTRUCTIONS
- DO NOT use a power supply that does not meet the specifications. This is a fire hazard and may lead to unit failure.
- DO NOT use outdoors. This unit is intended for indoor use only.
- DO NOT expose unit to an extremely humid environment or submerge in water. This may lead to unit failure.
- DO NOT place unit in close contact with any other objects while powered on because unit may overheat.
- KEEP lens (E) away from sharp objects. This may break the lens and lead to unit failure.
- DO NOT cover or place objects on the power supply (G). It should not be contained in an airtight space.
MAINTENANCE
- Keep the unit clear of dust. To clean, unplug the unit and use a clean, dry cloth to remove accumulated dust from between each Heat Sink Fin (D).
- Keep the Lens (E) clean. If the lens becomes contaminated with water, dust, or other particles, unplug the unit and clean the lens with isopropyl alcohol. Wet a cotton swab or a napkin in isopropyl alcohol, gently wipe the surface of the lens and let dry.
TROUBLESHOOTING GUIDE
Problem | Solution |
---|---|
Light doesn’t turn ON | Make sure the unit is connected to the power |
supply and the power supply is connected to an outlet with the correct
specifications.
Make sure electrical power is available to the AC outlet being used.
Make sure the power supply has the right specifications.
Make sure the device is operating within the specified operating temperature
range (below 104°F or 40°C). If the unit overheats, it will automatically shut
down.
Unit is flickering| Make sure you are using a power supply with the
correct specifications.
Make sure to operate the unit in a room at 104°F / 40°C or lower to prevent
overheating.
- Spectrum Tuning Dial
- Unit Link Cable
- Intensity Dial
A To next light
B Input from Controller
Controllability
Multiple A80 lights can be controlled either manually or by a single external 0-10V controller.
CABLES
Available cables:
- Control Cable (Please consult kessil.com for list of available cables and compatible controllers).
- Unit Link Cable (male/male with 3.5 mm stereo jack).
- Control Extension Cable (6′ male/female with 3.5 mm stereo jack).
STARTING A CHAIN
Connect two or more lights with the Unit Link Cable, as shown above.
CONTROL METHODS
There are two ways to control a chain of lights:
- With an external controller.
- Without external controller (Tuning Dials on the first light control all other lights in chain).
Each light has its own independent power supply. Any number of lights can be daisy chained together without degradation of signal. However, in longer chains a slight delay in response may occur. Manual tuning is disabled when input cable is plugged in.
Top Mounting Adapter
Remove the two screws on the back of A80, and use them to secure Top Mounting Adapter (H) to A80, then use two wood screws (I) to mount them.
Optional Accessories
A80 Gooseneck
(L=10 in)
For other accessories, please visit www.kessil.com.
kessil.led
kessiltube
@kessil
@kessilled
kessil.com
Kessil Lighting
A DiCon Brand
1689 Regatta Blvd, Richmond, CA 94804
510-620-5250
Kessil.com
This is a LED light source emitting 40 % or more of total radiation power of the range 250-800 nm in the range of 400-480 nm, and intended for coral growth.
ver. A2
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>