BUFFALO CU600 Bistro Contact Grill Instruction Manual

BUFFALO CU600 Bistro Contact Grill

Specifications :

• Model: Bistro Contact Grill
• Brand: BUFFALO
• Power: CU600
• Voltage: Standard electrical outlet
• Material: Stainless steel
• Dimensions: Varies by model

Product Usage Instructions

Installation

1. Place the unit on a heat-resistant surface, maintaining proper ventilation space.
2. Avoid proximity to flammable materials, water, and countertop edges.

Operation

1. Clean the cooking surface with warm soapy water before first use and ensure it is dry.
2. Lightly oil the cooking surface before heating up the appliance.
3. Turn on the power switch and set the desired temperature using the thermostat.
4. Wait for the appliance to heat up; the HEAT indicator light will turn off when the set temperature is reached.
5. Place food on the lower plate, close the upper plate, and cook as needed.
6. After use, turn the thermostat to ‘MIN’ and power switch to ‘O’ to turn off.

Safety Instructions

• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
• Consult Local and National Standards to comply with the following:
  • Health and Safety at Work Legislation
  • BS EN Codes of Practice
  • Fire Precautions
  • IEE Wiring Regulations
  • Building Regulations
• Caution! Hot surface! The temperature of the heating surface and other accessible surface is very high during use. Touch the temperature control knob only.
• DO NOT immerse the appliance in water.
• DO NOT clean with jet/pressure washers.
• DO NOT move or carry the appliance when it is switched on.
• DO NOT leave the appliance unattended during operation.
• Always use oven gloves when cooking or carrying out any adjustments to the appliance.
• Where this appliance is to be positioned in close proximity to a wall, partitions, kitchen furniture, decorative finishes, etc., it is recommended that they be made of non-combustible material; if not, they shall be clad with suitable with non-combustible heat-insulating material, and the closest attention be paid to fire prevention regulations.
• Do not obstruct any ventilation openings in the appliance body.
• Always use the handle to lift the plate.
• Always switch off and disconnect the power supply to the appliance when not in use.
•  This appliance must only be used in accordance with these instructions and by persons competent to do so.
• Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• BUFFALO recommend that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity and Functional Testing.
• BUFFALO recommend that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product.

Pack Contents
The following is included:

• Buffalo Bistro Contact Grill
• Instruction manual

BUFFALO prides itself on quality and service, ensuring that at the time of unpacking the contents are supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.

Installation

1. Place the unit on a heat-resistant surface. Avoid placing it on or close to flammable materials. Maintain a distance of 20cm (7 inches) between the appliance and walls or other objects for ventilation.
2. Keep the unit away from splashing water and countertop’s edge.

Operation

Model shown: CU600

Cooking
Note: Before using for the first time, clean the cooking surface with warm soapy water. Let dry completely and ensure no water goes into the appliance inside.
Note: It is recommended the cooking surface be lightly oiled before cooking.

1. Close the plates.

2. Connect the appliance to the mains power supply.

3. Turn the appliance on. The power indicator light illuminates.

4. Set the thermostat to the desired temperature (50°C-300°C). The HEAT indicator light turns On and the appliance begins to heat up.
   Note: 200°C to 220°C is suitable for general cooking.

5. When the set temperature is reached, the HEAT indicator light turns Off.
   Note: During use, the HEAT indicator light will cycle on/off, indicating the set temperature is being maintained.

6. Lift the upper plate and place the foodstuff on the lower plate.

7. Lower the upper plate.

8. Turning off: After use, set the thermostat to ‘MIN’ position and power switch to ‘O’ position.

Overheating protection

This appliance is featured with an overheat protection. Should the temperature exceed safe levels the
appliance will automatically cut off power.
The thermal Cut-out switch is located on the rear of the appliance. To reset the appliance after a sufficient cool-down period:

1. Unscrew the reset switch cover.
2. Press the small reset switch down until it clicks, using a blunt pointed instrument.
3. The appliance is now reset and can be used as normal.

Cleaning, Care & Maintenance

Warning:
Always turn off and disconnect the appliance from the power supply before cleaning.
Always allow the appliance to cool before cleaning.
If grease is permitted to accumulate, it will begin to carbonised into a hard substance that is extremely difficult to remove. To prevent this follow the cleaning steps below:

• Regularly remove excess grease or fat using a cloth dampened with warm soapy water.
• Take care when using scrapers to remove cooking residues as they can damage the cooking surface.
• Dry thoroughly after cleaning.

For best performance, BUFFALO recommend that the appliance is cleaned after each day of operation.
Failure to clean the appliance regularly may result in premature activation of the thermal cut-out switch.

Scraping

• After each use, scrape the appliance with a soft plastic or wooden scraper to remove excess fat and food.
• If there is an accumulation of burned fat or food, the cooking surface should be thoroughly scoured.

Caution

• It is vital that the cooking surface is lightly oiled after scouring. Do not use steel wool as it may leave shards that could contaminate food.

Waste Tray

• This appliance is featured with a waste tray to collect any liquid or fats that run off during cooking.
• At least once a day, remove and empty the waste tray before washing with warm soapy water. Do not allow the tray to overfill. Warning: DO NOT remove the tray during or immediately after use as the contents are still hot.

Troubleshooting

A qualified technician must carry out repairs if required.

plugged in correctly and switched on
Plug or lead is damaged| Replace plug or lead
Fuse in the plug has blown| Replace the fuse
Mains power supply fault| Check mains power supply
HEAT indicator light comes on but appliance does not heat up| Faulty element| Consult a qualified technician
Faulty thermostat| Consult a qualified technician
Thermostat set incorrectly| Check thermostat
Appliance slow to heat up| Cooking surface not clean| Clean cooking surface
Faulty element| Consult a qualified technician
Surface flaking| Build up of carbonised food debris| Refer to “Cleaning, Care & Maintenance” section
No power| Thermal cut-out switch has been activated| Check the machine is safe with no obvious damage and then press the re-set switch on rear of unit

Technical Specifications

Note: Due to our continuing program of research and development, the specifications herein may be subject to change without notice.

Model| Voltage| Power| Plate Type| Dimensions H x W x D mm| Net Weight
---|---|---|---|---|---
Top| Bottom
CU600| 220-240V~

50/60Hz

| 1450W| Rib| Rib| 200 x 310 x 310| 14.4kg
CU601| Flat| Flat| 14kg
CU602| 2200W| Rib| Rib| 200 x 430 x 310| 19.3kg
CU603| Flat| Flat| 19.1kg
CU604| 2900W| Rib| Rib| 200 x 570 x 310| 27.8kg
CU605| Flat| Flat| 25.2kg
CU606| Rib| Flat| 25.3kg

Electrical Wiring
This appliance is supplied with a 3 pin BS1363 plug and lead. The plug is to be connected to a suitable mains socket. This appliance is wired as follows:

• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E

This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Compliance
The WEEE logo on this product or its documentation indicates that the product must  not be disposed of as household waste. To help prevent possible harm to human  health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of  this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.
BUFFALO parts have undergone strict product testing in order to comply  with regulatory standards and specifications set by international,  independent, and federal authorities.

BUFFALO products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of BUFFALO.
Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to change specifications without notice.

DECLARATION OF CONFORMITY

I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and Standard(s).

Date

http://www.buffalo-appliances.com/

References

• Buffalo Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>