VICSEED VDPI01014C Dash Phone Mount for Car User Manual
- June 15, 2024
- vicseed
Table of Contents
VICSEED VDPI01014C Dash Phone Mount for Car User Manual
Specifications
Product Name: Easy Clip Car Mount
Model: CTEZ11
Applicable Places: Windshield, Dashboard, Air Vent
Phone Width for the Car Mount: 55mm-100mm
Retractable Length of the Telescopic Arm: 108mm-150mm
Adjustable Height of the Adjustable Legs: 0mm-15mm
Package List: Car Mount x1, Suction Cup x1, 3M Dashboard Pad x1, Air Vent
Clip x1, User Guide x1
The parameters above are derived from the laboratory of VICSEED. The actual parameters may differ from product to product or other factors. All images shown here are for reference only.
Overview
Attentions
- Please install the car mount in a suitable place before starting the journey, do not operate and adjust the car mount while driving.
- Do not install the car mount in a position that interferes with the operation of the airbag or hinders driving.
- Keep the car mount away from children.
Tips for Using the Suction Cup
- If the surface is flat and smooth, you can use the suction cup on the dashboard directly; While the surface is flat but not smooth, please use the suction cup on the dashboard pad.
- Do not stick the suction cup to curved surfaces, plush fabric or uneven surfaces. Otherwise it would not be attached securely.
- It is not recommended to attach the suction cup to the surface of leather, wall or glass film, because the suction cup with strong viscosity and attractiveness, which may cause surface damage.
- If the suction cup is frequently used in high temperature, low temperature or humid conditions, the suction force will decrease; Please avoid direct exposure to the sun for a long time.
- After using it for a while, if the suction is not sticky enough, please take down the suction cup and wash it with warm soap water. It will be sticky again after drying.
- Please protect the suction cup with plastic wrap when not in use.
Installation Steps
Method 1 – Use with the Suction Cup
-
Unscrew the fixed nut completely, let the ball joint pass through the fixed nut (The thread must face to the groove). Push the ball joint firmly into the groove on the back of the car mount.
-
Tighten the fixed nut.
-
Choose a flat surface on the dashboard, and clean the surface where you need to install the car mount with a wet cloth. Wait it to dry, and then install the dashboard pad. Tear off the red protective sticker of 3M dashboard pad, stick the pad to the position where you want to install the car mount. Press it firmly for 1 minute to fix it. Let it sit for 24 hours before installing the car mount.
The 3M dashboard pad is disposable. Once pasted, it’s hard to remove. Once applied, it cannot be used again. Please choose the appropriate position to install the 3M dashboard pad.
-
Attach the suction cup to the windshield/dashboard hard and press the suction cup lock to bottom position (not the middle position) to secure the car mount.
-
Adjust the angle of the car mount to fit your view. (Twist the extendable arm adjusting nut to adjust the length of the arms. Twist the extendable arm retaining nut to change the angle of the arms.)
Method 2 – Use with the Air Vent Clip
-
Unscrew the fixed nut completely, let the ball joint pass through the fixed nut (The thread must face to the groove). Push the ball joint firmly into the groove on the back of the car mount.
-
Tighten the fixed nut.
-
Twist the Locking Handle to adjust the opening of the clip to fit the air vent.
-
Please insert the car mount into a suitable place on the air vent. Then tighten the Locking Handle to secure the car mount firmly and adjust the angle of the car mount to fit your view.
Using Steps
-
Press the quick release button and the clamps automatically open. Then put your phone into the holder and pull the adjustable legs according to the size of your phone, to ensure that your phone is clamped securely.
-
Place your phone into the holder and press the clamp arms towards each other. Then press the clamp arms with a little force again until you hear the “click”. Your phone will be secured by the arm clamps.
