Wi-Tek WI-PCMS306GF-I Industrial Cloud Managed Switch Installation Guide
- July 25, 2024
- Wi-Tek
Table of Contents
Wi-Tek WI-PCMS306GF-I Industrial Cloud Managed Switch
Specifications
- Model: WI-PCMS306GF-I | WI-PCMS310GF-I | WI-PCMS312GF-BT-I
- Ports:
- WI-PCMS306GF-I: 4 x Gigabit PoE+ Ports, 2 x 1000Mbps SFP Slots
- WI-PCMS310GF-I: 8 x Gigabit PoE+ Ports, 2 x 1000Mbps SFP Slots
- WI-PCMS312GF-BT-I: 8 x Gigabit PoE++ Ports, 4 x 1000Mbps SFP Slots
- Power Input:
- POE: 48-57V DC
- NON POE: 12-55V DC
FAQ
- Q: How do I reset the switch if needed?
- A : To reset the switch, locate the reset button on the device and hold it down for at least 10 seconds until the switch reboots.
- Q: Can I stack multiple switches together for increased capacity?
- A: Yes, these switches support stacking to increase port capacity and manageability. Refer to the user manual for detailed instructions on stacking.
Packing Content
Appearance Overview
For WI-PCMS306GF-I
- Front panel
- Back panel
WI-PCMS306GF-I DIP Switch Description
Fast Ring| One-key enables fast ring function, supports fast network self-
healing
SCP| Enable storm suppression to improve network reliability
LED Indicator Description
PWR| On: The switch is powered on
Off: The switch is powered off or the power supply is abnormal
SYS| Blinking: The switch works properly
Off: The switch works improperly
PoE| Off: PoE not working
On: PoE working
Link
| On: Port connected Blinking: Data transmission
Off: Port disconnected
For WI-PCMS310GF-1
- Front pane l
- Back panel
WI-PCMS310GF-I DIP Switch Description
Fast Ring| One-key enables fast ring function, supports fast network self-
healing
SCP| Enable storm suppression to improve network reliability
LED Indicator Description
PWR| On: The switch is powered on
Off: The switch is powered off or the power supply is abnormal
SYS| Blinking: The switch works properly
Off: The switch works improperly
PoE| Off: PoE not working
On: PoE working
Link
| On: Port connected Blinking: Data transmission
Off: Port disconnected
For WI-PCMS312GF-BT-I
- Front panel
- Back panel
WI-PCMS312GF-BT-I DIP Switch Description
Fast Ring| One-key enables fast ring function, supports fast network self-
healing
SCP| Enable storm suppression to improve network reliability
LED Indicator Description
PWR| On: The switch is powered on
Off: The switch is powered off or the power supply is abnormal
SYS| Blinking: The switch works properly
Off: The switch works improperly
PoE| Off: PoE not working
On: PoE working
Link
| On: Port connected Blinking: Data transmission
Off: Port disconnected
DIN-rail Installation
Please follow the steps below
DC Power Cable Connection
This switch can work with 48~57V DC power, the DC power connection processes are as follows.
- Before installation, ensure the device is disconnected from the power supply.
- Connect one end of the protective grounding cable to the grounding screw on the side panel of the device, and the other end is well grounded nearby.
- Connect the positive and negative wires of DC power separately to the “+” and “-” power terminal of 48~57V power 1 or 48~57V power 2 on the switch as following figure, using a screwdriver to screw stably.
- The redundant power can be connected with the DC power so that one power supply can still work in case the other one fails.
- Turn on the DC power, and check if the power supply indicator of power 1 or power 2 turns on, which means the main power (Power 1) or backup power (Power 2) is connected correctly
Login WEB UI
Log in to the switch locally
Let the Switch obtain an IP address and then check the DHCP server to see
which IP address was assigned. The Switch is set to DHCP by default, so it
will try to obtain an IP address automatically. If that fails, then it will
use the default fallback IP address, 192.168.0.1
To log in, follow these steps:
- Launch your web browser. you type the appropriate IP address in the address bar
- The login screen will appear. The default username and password are both admin
Use the console cable to access the switch
- Connection Diagram
Industrial Cloud Managed Switch
- Step 1 Download a PuTTY software
- Step 2 Use the Console cable to connect the computer and the switch as shown in the above figure
- Step 3 Set the com port number of the Console line and the baud rate of the switch in the software (steps as shown in the figure below).
Notice
- Step 2 is your computer recognizes the COM number of the Console line
- Step 3 is the baud rate of the exchange (the baud rate of the switch is 9600)
Note: If the switch device is not connected to the cloud platform, the management account password is admin by default. If it is connected to the cloud platform for management, please go to the cloud platform to check the password. The account is admin, and the password is the WEB password you set when creating the project
Use Telnet to log in to the CLI mode of the switch
Connection Diagram
Industrial Cloud Managed Switch
- Step 1 Configure the IP address of the computer and the IP address of the same segment as the switch
- Step 2 Open the cmd window of the computer
- Step 3 Enter Telnet followed by the management IP address of the switch (for example, if the management IP address of the switch is 192.168.0.1, enter Telnet 192.168.0.1
Note: If the switch device is not connected to the cloud platform, the management account password is admin by default. If it is connected to the cloud platform for management, please go to the cloud platform to check the password. The account is admin, and the password is the WEB password you set when creating the project.
Cloud login switch configuration
- Log in to the cloud management interface (No account, you need to register an account to log in，The URL is：http://cloud2wireless-tek.com)
Enter the cloud binding switch
(explain: The switch must be connected to the Internet to bind successfully)
Please enter the device serial number to bind a device to the current
group, device can be off when binding.
(Explanation: The 17-digit SN code of the switch is shown on the sticker on
the back of the switch as shown in the figure below
After binding, you can use the Switch in the Tunnel option in the cloud
management, and then choose to use EWEB or TELNET to enter the switch
(After entering the switch, you can configure it based on your own needs)
Warranty
Warranty Card
- Username…………..
- Address……………
- Telephone No………………
- Purchase Shop…………….
- Purchase Address……………
- Product Model No……………..
- Purchase Time……………….
- Serial No……………….
- Dealer Signature……………..
If the product defects within three months after purchase, we will provide you with a new product of the same model.
- If the product defects within the three-year warranty period, we will provide professional maintenance service.
- Proof of purchase and a complete product serial number are required to receive any
- services guaranteed as part of the limited warranty.
- Any other defects that are not caused by workmanship or product quality, such as natural disasters, water damage, extreme thermal or environmental conditions, sticker damage, or warranty card loss will disqualify the product from the limited warranty
Technical Support
Company Website
Cloud Management
CONTACT
- Wireless-Tek Technology Limited
- Address : Building 3, Units 1801-1807, 1812,
- Huaqiang Era Plaza, Tangwei Community,
- Fuhai Street, Bao’an District, Shenzhen City,
- Guangdong Province, China.
- Website :www.wireless-tek.com
- Tel :86-0755-32811290
- Email :sales@wireless-tek.com
- Technical Support :tech@wireless-tek.com
References
- Test and Measurement Equipment | Tektronix
- Wireless-Tek Technology Limited.
- Wireless-Tek Technology Limited.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>