signify IS M_RDL ModuLyte 4 Inch Downlighting Instruction Manual

signify IS M_RDL ModuLyte 4 Inch Downlighting

Product Information

Specifications:

• Product Name: ModuLyte Downlighting
• Model Number: IS M_RDL 442296555701
• Available Sizes: 4in, 6in, & 8in
• Compliance: Class A digital service, FCC Part 15
• Dimensions:
  • 4in Round: Standard cutout 4.87” (123.698mm)
  • 6in Round: Standard cutout 6.37” (161.798mm)
  • 8in Round: Standard cutout 8.37” (212.598mm)

Product Usage Instructions

• Step 1: Select CCT and Lumen Output
  Select the desired settings before connecting the luminaire to power.

• Step 2: Open Driver Box
  Push the lock upwards to open the driver box and route the main leads through the knockout. Secure the box after completion.

• Step 3: Make Ceiling Cutout
  Ensure the ceiling is clear of obstructions and make the appropriate cutout as per the dimensions provided.

• Step 4: Pass the Driver Box Through the Ceiling Hole
  Feed the driver box through the ceiling hole and attach it to the luminaire cord. Optionally, attach the driver box to the T grid.

• Step 5: Connect Luminaire
  Align the notch and knob on the driver box with the luminaire and secure by turning the screw clockwise. Detach by turning the screw in the opposite direction.

• Step 6: Insert Trim Springs
  Bend and insert the springs of the luminaire into the ceiling hole for secure installation.

FAQ:

• Q: Can this product be installed by a non-professional?
  A: No, installation and servicing must be performed by a qualified electrician or service personnel.

• Q: What tools are required for installation?
  A: Tools and accessories needed are not included in the product.

Safety Information

CAUTION:
THE INSTALLATION AND SERVICING OF THIS PRODUCT MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL.

NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital service, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Read and understand these instructions before installing the luminaire (fixture)
This luminaire is intended for installation by the National Electrical Code and local regulations. To ensure full compliance with local codes and regulations, check with your local electrical inspector before installation.

WARNING
To prevent electrical shock, turn off electricity at the fuse box before proceeding. Allow mixture to cool before handling.

Retain these instructions for maintenance reference

ModuLyte accepts Light Engines:

• M4RDL, M6RDL & M8RDL

Warning (RISK OF FIRE):
Use only with ModuLyte LED light engines and reflectors.

WARNING
Make sure that the power supply is disconnected before installation.

Tools/accessories needed

Tools/accessories needed (not included)

• Work Gloves
• Safety Glasses
• A Flat Screwdriver

Cutout Dimensions

• 4in
  Round: Standard cutout 4.87’’ (123.698mm)

• 6in
  Round: Standard cutout 6.37” (161.798mm)

• 8in
  Round: Standard cutout 8.37” (212.598mm)

Parts

Installation Instruction

Step 1
Select the CCT and Lumen Output of the luminaire before connecting it to power (Figure 1).

Step 2
Select the knockout that best suits your installation, insert the flat screwdriver into the knockout opening, and start moving it up and down to remove it (Figure 2).

WARNING
Use work gloves to protect your hands from sharp metal when removing knockouts.

Step 3

• Push the lock upwards to open the driver box and route the main leads through the knockout that was removed, once completed close the box (Figure 3).
• Note: Use appropriate cable clamps or conduit lock nuts as applicable

Step 4

• Make the ceiling cutout. Ensure that there is nothing in the ceiling to obstruct the installation (Figure 4).
• Note: Confirm the dimensions needed for your installation in the “Cutout Dimensions” section on page 1.

Step 5

• Pass the driver box through the ceiling hole and retain the cord to attach to the luminaire.
• Note: If preferred, the driver box can be attached to the T grid by bending the hooks backward and attaching them to the T bar (Figure 6).

Step 6

• Connect the luminaire (Figure 8).
• Note: To connect the driver to the luminaire, align the notch and the knob and push it in, then turn the screw clockwise to secure, to detach it turn the screw to the opposite side and pull the attachment (Figure 7).

Electrical Diagram

Step 7

• Bend the springs of the luminaire and insert it into the ceiling hole (Figure 9).
• Notes: Do not place the driver box on top of the light engine. WARNING – Watch out for falling parts and Make sure the springs open back to position once the luminaire is inserted to prevent any risk of injury.

© 2024 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract unless otherwise agreed by Signify.

Contact Information

• Signify North America Corporation 400 Crossing Blvd, Suite 600 Bridgewater, NJ 08807

• Telephone: 800-555-0050

• Signify Canada Ltd.
  281 Hillmount Road, Markham, ON, Canada L6C 253

• Telephone: 800-668-9008

All trademarks are owned by Signify Holding or their respective owners.

www.lightolier.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>