signify BP-F Clearscape Base Plate Instruction Manual

signify BP-F Clearscape Base Plate Instruction Manual

Installation Instruction

IMPORTANT : FOR YOUR PROTECTION, YOU MUST CAREFULLY READ ALL WARNINGS AND INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO INSTALLATION, OPERATION, SERVICE OR MAINTENANCE. FAILURE TO DO SO CAN RESULT IN DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. If you do not understand these warnings and instructions, or if additional information is desired, please contact Signify, Lumen. TSC@signify.com phone 1-833-744-6439.

• Installation, service and maintenance of luminaires must be performed by a qualified professional and in accordance with all federal, state and local laws, regulations and electrical codes. This professional should be familiar with the construction and operation of this product and any hazards involved. If not qualified, do not attempt installation, service or maintenance.
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts, abrasions and other hazards, please read all warnings and instructions included with the luminaire, on the luminaire’s packaging and affixed to the luminaire itself.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaire’s construction and operation and any hazards involved.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

• Disconnect or turn off power before attempting any installation, service or maintenance.
• Verify that supply voltage is correct by referencing the luminaire label information.
• Make all electrical and ground connections in accordance with the National Electrical Code (NEC) and any other applicable laws, regulations or codes.
• All wiring connections should be capped with UL-approved wire connectors.

WARNING

RISK OF FIRE OR PERSONAL INJURY

• Keep combustible materials away from LED/lamp & lens
• Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

• Allow Led/lamp & lens to cool before handling.
• Do not touch enclosure or light source
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations, instructions and restrictions for driver type, burning position, mounting locations and replacement.

CAUTION

RISK OF PRODUCT DAMAGE

• Never connect luminaires and/or components under load with supply voltage turned on.
• Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation.
• Do not restrict fixture ventilation. Allow for some volume of airspace around luminaire. Avoid covering luminaire with insulation, foam or other material that will prevent convection or conduction cooling.
• Do not exceed luminaire maximum ambient temperature.
• Do not modify the luminaire.
• Only use luminaire in its intended application and location.
• Led products are polarity sensitive. Ensure proper polarity before installation.
• Electrostatic Discharge (ESD) can damage LED. Personal grounding equipment must be worn during all installation and servicing of the luminaire.
• Do not touch individual electrical components as this can cause ESD, shorten LED life, or impact LED performance.
• Some components inside the luminaire may not be serviceable. In the unlikely event your luminaire may require service, stop using it immediately and contact Signify.
• Always read the luminaires complete installation instructions prior to installation for any additional luminaire specific warnings.
• In the case of HID or Fluorescent luminaires, regular re-lamping is required to keep luminaire  operating within safe limits
• Do not install damaged product. Handling and installing damaged products can potentially increase the risks mentioned In case of damage and/or missing parts upon arrival of the luminaire.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation or maintenance.
• Please see luminaire specific Installation and Maintenance Instruction for additional warnings or any applicable FCC or regulatory statements. Failure to follow any of these Instructions could void luminaires warranties.

Luminaire Maintenance

• Regular luminaire maintenance programs are recommended.
• It is recommended to clean the outside of the luminaire and the refractor/lens.
• Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user.
• If clean water is not sufficient for cleaning, use a neutral, synthetic, not-scratching and not abrasive cleaning substance.
• Never use alkaline and/or acetous cleaning substances.
• Make sure that the cleaning substance is carefully removed by rinsing with lots of clean water.
• Signify recommends using a cleaning solution that has a PH between 5 and 8.
• Recycle: For information on how to recycle electronic products and components, please visit www.epa.gov.

BP-(F) for CSFS/CSFM Installation Sheet

Step 1:
Ensure the pad or wall mount employs four ½” anchor bolts, with the pattern shown, forming a 4” X 5” rectangular pattern.

Step 2:
Place the base plate over the mounting bolts (center bolt in image is welded to the plate)

Step 3:
Install the ½” nuts, lock washers, and flat washers (by others) to secure the plate to the mounting surface.

Step 4:
Ensure the hardware is torqued to 58 ft-Lbs.

Step 5:
Place the trunnion onto the center bolt, and secure the fixture with the ½”-13 nut, split washer, and flat washer provided.

Step 6:
Ensure the center nut is torqued to 58 ft-Lbs. Make electrical connections following applicable electrical codes.

2020 Signify Holding. All rights reserved. This document may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. All trademarks are owned by Signify Holding or their respective owners.

Signify North America Corporation 200 Franklin Square Drive.
Somerset, NJ 08873 Telephone 855-486-2216

Signify Canada Ltd. 281 Hill mount Road.
Markham, ON, Canada L6C 2S3
Telephone 800-668-9008

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>