signify Garage and Canopy Dualselect Round User Guide

: May 15, 2024
: signify

Table of Contents

signify Garage and Canopy Dualselect Round
Product Information
Product Usage Instructions
WARNINGS AND INSTRUCTIONS FOR LUMINAIRES
Luminaire Maintenance
Garage & Canopy
GENERAL SAFETY INFORMATION
GENERAL WIRING DIAGRAM
Sensor Function
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

signify Garage and Canopy Dualselect Round

signify-Garage-and-Canopy-Dualselect-Round-product-
image

Product Information

Specifications :

Manufacturer: Signify
Email: SanMarcos.TSC@signify.com
Phone: 800-227-0758

Product Usage Instructions

Installation:

Before starting the installation process, carefully read and understand all warnings and instructions provided in the user manual.
Installation, service, and maintenance of the luminaires must be carried out by a qualified professional in compliance with federal, state, and local laws and electrical codes.

Warnings:

Disconnect or turn off power before attempting any installation, service, or maintenance.
Make sure the supply voltage is correct by referencing the luminaire label information.
All wiring connections should be capped with UL-approved wire connectors.

Usage Precautions:

Avoid operating the luminaire in close proximity to combustible materials or substances affected by heat or drying.
Wear gloves and safety glasses when handling the luminaire to prevent personal injury.
Avoid direct eye exposure to the light source while it is on.

Maintenance:

Maintenance of the luminaires should be performed by individuals familiar with the product’s construction and operation.
Allow LED/lamp & lens to cool before handling to prevent any risk of fire, electric shock, or personal injury.

Frequently Asked Questions (FAQ)

Q: Can I install the product by myself?
A: Installation, service, and maintenance must be performed by a qualified professional to ensure safety and compliance with regulations.
Q: What should I do if the product is damaged?
A: Do not install damaged products. Handling and installing damaged products can increase risks. Contact Signify for further assistance if the product is damaged or missing parts.

INSTALLATION

WARNINGS AND INSTRUCTIONS FOR LUMINAIRES

IMPORTANT: FOR YOUR PROTECTION, YOU MUST CAREFULLY READ ALL WARNINGS AND INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO INSTALLATION, OPERATION, SERVICE OR MAINTENANCE. FAILURE TO DO SO CAN RESULT IN DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. If you do not understand these warnings and instructions, or if additional information is desired, please contact Signify at SanMarcos.TSC@signify.com or phone 800-227-0758.

Installation, service and maintenance of luminaires must be performed by a qualified professional and in accordance with all federal, state and local laws, regulations and electrical codes. This professional should be familiar with the construction and operation of this product and any hazards involved. If not qualified, do not attempt installation, service or maintenance.
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts, abrasions and other hazards, please read all warnings and instructions included with the luminaire, on the luminaire’s packaging and affixed to the luminaire itself.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaire’s construction and operation and any hazards involved.

WARNING
RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Disconnect or turn off power before attempting any installation, service or maintenance.
Verify that supply voltage is correct by referencing the luminaire label information.
Make all electrical and ground connections in accordance with the National Electrical Code (NEC) and any other applicable laws, regulations or codes.
All wiring connections should be capped with UL-approved wire connectors.

WARNING

RISK OF FIRE OR PERSONAL INJURY
Keep combustible materials away from LED/lamp & lens
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

WARNING

RISK OF PERSONAL INJURY
Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source while it is on.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY
Allow LED/lamp & lens to cool before handling.
Do not touch enclosure or light source
Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations, instructions and restrictions for driver type, burning position, mounting locations and replacement.

CAUTION
RISK OF PRODUCT DAMAGE

Never connect luminaires and/or components under load with supply voltage turned on.
Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation.
Do not restrict fixture ventilation. Allow for some volume of airspace around luminaire. Avoid covering luminaire with insulation, foam or other material that will prevent convection or conduction cooling.
Do not exceed luminaire maximum ambient temperature.
Do not modify the luminaire.
Only use luminaire in its intended application and location.
LED products are polarity sensitive. Ensure proper polarity before installation.
Electrostatic Discharge (ESD) can damage LED. Personal grounding equipment must be worn during all installation and servicing of the luminaire.
Do not touch individual electrical components as this can cause ESD, shorten LED life, or impact LED performance.
Some components inside the luminaire may not be serviceable. In the unlikely event your luminaire may require service, stop using it immediately and contact SanMarcos.TSC@signify.com or phone 800-227-0758.
Always read the luminaire’s complete installation instructions prior to installation for any additional luminaire specific warnings.
In the case of HID or Fluorescent luminaires, regular re-lamping is required to keep luminaire operating within safe limits
Do not install damaged product. Handling and installing damaged products can potentially increase the risks mentioned. In case of damage and/or missing parts upon arrival of the luminaire, please contact SanMarcos.TSC@signify.com or phone 800-227-0758.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to SanMarcos.TSC@signify.com or phone 800-227-0758.
Please see luminaire specific Installation and Maintenance Instruction for additional warnings or any applicable FCC or regulatory statements. Failure to follow any of these Instructions could void luminaire warranties.

Luminaire Maintenance

Regular luminaire maintenance programs are recommended.
It is recommended to clean the outside of the luminaire and the refractor/lens.
Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user.
If clean water is not sufficient for cleaning, use a neutral, synthetic, not-scratching and not-abrasive cleaning substance.
Never use alkaline and/or acetous cleaning substances.
Make sure that the cleaning substance is carefully removed by rinsing with lots of clean water.
Signify recommends using a cleaning solution that has a PH between 5 and 8.
Recycle: For information on how to recycle electronic products and components, please visit www.epa.gov.

Garage & Canopy

GCR60-SCT-G1-SM-5-10-BZ GCR90-SCT-G1-SM-5-10-BZ
LED Lighting Fixture

$signify-Garage-and-Canopy-Dualselect-Round-fig- $2$$

GENERAL SAFETY INFORMATION

To avoid hazards and unnecessary failures due to misuse, please read carefully all warnings and instructions included in the MI sheets and all labels.

Before installing, servicing, or performing routine maintenance upon this equipment, pay attention to: Supply voltage input 120-347V, frequency 50/60 Hz.
This ﬁxture is intended to be connected to a properly installed and grounded UL listed junction box.
Commercial installation, service and maintenance of luminaires should be performed by a qualiﬁed licensed electrician.
Residential installation, always consult a qualiﬁed licensed electrician and check your local electrical code with any uncertainty before operating.
Always check the product before installation.
DO NOT INSTALL DAMAGED PRODUCT!

WARNING : RISK OF ELECTRICAL SHOCK

Always turn oﬀ the power before you perform installation and maintenance.
Verify that supply voltage is correct for the specified voltage range of the luminaire shown on the label, i.e. 120-347V.
Make all electrical and grounded connections in accordance with the National Electrical Code and any applicable local code requirements.
All wiring connections must be capped with UL approved devices for this purpose.

CAUTION: RISK OF INJURY

Wear gloves and safety goggles at all times when removing luminaires from carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the illuminated light source.
Put aside small parts and dispose of the packing material properly to prevent hazards to children.

CAUTION: RISK OF FIRE
Install and use only as intended according to UL, all applicable codes and regulations and these instructions.

CAUTION: To reduce the risk of water ingress, turn the fixture off and let it cool down to the ambient temperature before spraying it with water for cleaning.
Illustrations in the manual are for installation purpose only. Installation may vary depending on the specific luminaire model.

GENERAL WIRING DIAGRAM

CAUTION: Turn off electrical power by fuse or circuit breaker box before wiring fixture to the power supply . $signify-Garage-and-Canopy-Dualselect- Round-fig- $3$$

Garage & Canopy

Surface-mounted with J-BOX
Before starting, ensure that the electrical power is disconnected. Unpack the fixture and ensure there is no damage.
Install the connecting plate onto the ceiling or junction box (supplied by others) and pull the wires through center hole.
Hang the fixture onto the connecting plate while connecting the power cable wires as seen below.
Slide the fixture back into the connecting plate and tighten the screw fixing the plate to the housing. $signify-Garage-and-Canopy-Dualselect-Round-fig- $4$$
Pendent Installation with 3/4 inch conduit
Feed incoming power leads through pendant stem (supplied by others).
Hanging pipe connection must be a rigid connection.
Connect wiring according to the schematic.
Screw pendant pipe onto the top of the fixture.
Be sure to wrap Teflon tape or silicone gel to thread of pipe to prevent moisture from entering.
To adjust the CCT and/or FAO switch(es), remove the 1/2-14NPS plug(s) as shown.
Note: To ensure the protective performance of the product, the 1/2-14nps plug must be assembled with a torque of no less than 1.7N·m. (15in-lbs.)
CCT switching position
For 3000K set the switch to 3KK as shown.
For 4000K set the switch to 4KK as shown (Default).
For 5000K set the switch to 5KK as shown.
FAO switching position
For GCR60-SCT-G2-SM-5-10-BZ
For 60W (maximum power):Switches 1&2 to off as shown ( Default). For 40W: Switch 1 to ON as shown, and Switch 2 is off.
For 28W: Switch 2 to ON as shown, and Switch 1 is off.
Note: Switch 3 Turns the Motion Sensor On/Off
For GCR90-SCT-G2-SM-5-10-BZ
For 90W (maximum power): Switches 1&2 are off as shown (Default). For 80W: Switch 1 to ON as shown, and Switch 2 is off.
For 70W: Switch 2 to ON as shown, and Switch 1 is off.
Note: Switch 3 Turns the Motion Sensor On/Off.

Sensor Function

Maximum mounting height is <15m (49ft.) to comply with sensor detection range.

Initialization
Upon initial powering, the sensor automatically turns on the light at 100% brightness. 10 seconds later, it turns off the light. During the initialization, the sensor is not able to detect movement.
After initialization, the sensor will function according to the programmed settings.
Operation Mode: Daylight Priority + 2-leveled dimming
2- leveled dimming function with Daylight priority
When Daylight is enough, >150 lux, motion sensing will be switched off and the light will be always off.
With insufficient ambient light, <50lux, motion sensing is activated.
When motion is detected, the light turns on. Hold-on time 5 min – No motion detected for 5 minutes, dim to 50%.

$signify-Garage-and-Canopy-Dualselect-Round-fig- $9$$

With sufficient ambient light, the light will not be switched on even when motion is detected.
With insufficient ambient light, the sensor switches the light on when motion is detected.
After the hold-time elapses, the sensor dims to the lower light level if no new motion is detected.

Turning the Sensor Off:

By Default, the Motion and Daylight sensor will be ON.
To Switch OFF the Sensor, move FAO Switch position 3 to the bottom position. 5.3.3 When the Sensor is turned OFF, the fixture will stay on 24/7.

Sensor Application Notice:
The distance between any inductive sensor luminaires should be greater than 3m. 5.4.2 According to installation height, note sensor detection area. (<15m or 49ft)

To prevent false triggers:

Avoid high-density objects, such as: metal, glass, concrete walls, etc., beyond the sensor detection area.
Avoid moving signals beyond the sensor detection area, such as: fan, DC motor, sewer pipe, air outlet, heavy rainfall, motion behind a thin wall, etc.
Avoid the shock & vibration environmental application.

The sensor programming always goes the process of initialization and Daylight Priority + 3-leveled dimming operational mode; to get customized setting, recommend to utilize the sensor remote, contact your dealer.
The parameters of the sensor may need to be reconfigured to adapt different installation environments, please refer to the remote instruction or contact the manufacturer.

This document may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed.
All trademarks are owned by Signify Holding or their respective owners.
Signify North America Corporation 200 Franklin Square Drive, Somerset, NJ 08873
- Telephone 855-486-2216
Signify Canada Ltd. 281 Hillmount Road, Markham, ON, Canada L6C 2S3
- Telephone 800-668-9008

www.stonco.com