signify ID-7608 LED Wall Verge Installation Guide

May 15, 2024
signify

signify ID-7608 LED Wall Verge Installation Guide

Installation Instructions

System Overview

These instructions review how to install Verge wall mount fixtures. Verge 4 ft and 8 ft modules can be installed as individual standalone units, or they can be joined together to create continuous rows. The graphic below shows the components required to install a typical row of Verge wall mount fixtures.

IMPORTANT: Read all instructions including fixture wiring AND mechanical details before beginning installation.
System Overview

  1. Verge Power Kits
    1x j-box cover
    1x strain relief

  2. Verge Left Endcap kit
    1x left endcap
    2x 1/2″ plugs
    2x #10-24 x 1/2″ screw

  3. Verge Joint Kits
    4x 1/2″ plug
    2x #10-24 lock nut
    2x #10-24 x 9/16″ bolt
    1x gasket

  4. Verge Right Endcap Kit
    1x right endcap
    2x 1/2″ plugs
    2x #10-24 x 1/2″ screw

TOOLS REQUIRED: Stubby Phillips screwdriver, 3/8 ” nut driver
ATTENTION: Install in accordance with national and local building and electrical codes

Module Lengths
Sync wall mount systems come in 4ft and 8ft modules. Overall module lengths are shown to the right. Module lengths do not include endcaps.
Module Lengths
Indicates overall length of fixture (excluding endcaps)

Endcaps
Add two endcaps to the overall length of each row.
Endcaps

Mount Spacing
©Mounts variable within 2″ – 5″ of end or joint. On 8ft module, additional mount to be located within 2″ – 5″ of center of module.
©Maximum distance between mounts is 48″.
Note: Fixture is lush with wall.

Row Configurations
The tables below indicate how 4ft and 8ft modules can be combined to create continuous rows of various lengths.

Nominal row length 4ft module 8ft module
4′ 1x
8′ 1x
12′ 1x
16′ 2x
20′ 1x 2x
24′
28′ 1x 3x
32′ 4x

IMPORTANT: Read all instructions at least once prior to beginning installation.
All mount brackets must be secured to wall structure (eg. studs or cross- braces)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

  1. Install utility box and utility box cover
    Installation Instruction

    Determine power feed location and install 2″x4″ utility box (supplied by others) parallel with fixture. Complete connections at utility box with supplied power cord. Attach cover bracket using supplied hardware. Punch power access hole in supplied cover, feed power cord through and attach strain relief on wall side. Attach cover using supplied painted hardware.
    NOTE: Bottom of utility box should be in line with bottom of wall brackets.

  2. Install wall brackets
    Installation Instruction

    Bottom of utility box should be in line with bottom of wall brackets
    Determine fixture mounting location and secure wall brackets to structure using appropriate fasteners (two per bracket, supplied by others). 4ft fixtures: Require two bracket assemblies; 8ft fixtures: Require three bracket assemblies. Brackets must be installed a maximum of5″ from end of fixture (on 8ft fixture, the third bracket can be 5″ of ether side of ingrown crispate).
    NOTE: Mounted fixture(s) will sit approximately /4″ above top edge of bracket assembly.

  3. Unpack / Prepare fixtures
    Arrange boxed fixtures on floor in specified locations; remove fixtures from boxes; remove plastic from fixtures. Cap all unnecessary power feed holes at back of fixture(s) using supplied 1/2″ plugs.

  4. Remove Top Reflector
    Installation Instruction
    Shift top reflector to the left and then remove the reflector.
    b Remove Front Reflector
    Installation Instruction

    Remove the screws holding the front reflector and then remove the front reflector.

  5. Raise Fixture and Engage on Wall Brackets
    Installation Instruction

    With 2 people, raise fixture into position and engage it on hooks located on top of wall brackets, then rotate it down into position. Secure bracket using supplied hardware.
    POWER LOCATIONS: Prior to engaging fixture in mounting brackets, feed installed power cord through the access hole at back of the fixture.

  6. Access Wiring / Remove Pan
    Installation Instruction

    To access wiring, remove screw from top pan and lift pan off. Apply strain relief to power cord.
    NOTE: Care should be taken when lifting up top reflector to avoid disconnecting internal wiring

  7. Complete electrical connections
    Installation Instruction

    Complete electrical connections using wire nuts (supplied by others). Re- install pan and hardware removed in STEP 5.

  8. Level and secure first fixture
    Installation Instruction

    LEVEL: Using 5/16″ hex nut driver, level fixture by adjusting the tilt screw.
    SECURE: Secure fixture to wall bracket assemblies by tightening the lock screw

  9. Install and join additional fixtures to create row
    Installation Instruction

    With two people, raise second fixture and engage on mounting brackets (see STEP 4). At joint, remember to insert black gasket.

  10. Complete electrical connections at joints
    Installation Instruction

    Complete in-row electrical connections.
    NON-POWER LOCATIONS: Use supplied quick-wire connectors. Tuck wires into wire cavity.
    POWER LOCATIONS: Remove installed quick-wire connectors and complete electrical connections using wire nuts (supplied by others). Tuck wires into wiring cavity.
    NOTE: Use smallest appropriate wire nuts.

  11. Level and secure additional fixture
    Installation Instruction
    Level second fixture by adjusting the tilt screw (see step 8). Slide second fixture flush against first fixture and secure joint using supplied nut and bolt hardware (requires 3/8 nut drivers). Secure fixture to wall brackets by tightening the lock screw at each bracket location (see step 8).
    Repeat steps 8-10 for each additional fixture(s) ingrown.

  12. Install Endcaps
    Installation Instruction

    Attach endcap to first and last module in each row using supplied hardware.
    IMPORTANT: Do not over-tighten endcap fasteners. Leda lite recommends tightening fasteners by hand.
    When nut is flush with crispate, turn an additional /4 turn.

  13. Re-install Front Reflector
    Installation Instruction

    Re-install front reflector using short (stubby) screwdriver.

  14. Install Light Guide and Re-install Top Reflector
    Installation Instruction

    Identify smooth side of the Light Guide and ensure it is installed smooth side DOWN.
    Install Light Guide panel into LED fixture after joining and wiring is complete. Ensure panel is seated correctly as shown above.
    Final Step: Install the top reflector and shift into place.

© 2019 Signify Holding. All rights are reserved. Reproduction in whole or part is prohibited without the written consent of the copyright owner. Phone: 604.888.6811
Page 3
Web: ledalite.com/products Revision D November 17, 2023

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals