signify GCM Wall Sconce Installation Guide

: May 15, 2024
: signify

Table of Contents

signify GCM Wall Sconce
Product Information
Product Usage Instructions
FAQ
I/S GEOFORM Installation Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

signify GCM Wall Sconce

signify-GCM-Wall-Sconce-PRODUCT

Product Information

Specifications:

Product Name: Wall Sconce GEOFORM GCM
Model Number: 442296087551
Manufacturer: Signify, Gardco
Phone: 1-833-744-6439

Product Usage Instructions

Installation Steps:

Install the Wall Mount Bracket with gasket to the J-Box. Apply 12 in-lbs torque until the gasket between wall and Wall Mount Bracket is properly compressed.
Ensure the Wall Mount Bracket is properly leveled.
Hold the fixture by the 2 hooks to the bottom of Wall Mounting Bracket. Ensure the wire passes in the middle between them.
Once luminaire is installed and hardware is properly torqued, make supply wiring connections according to the appropriate wiring diagram.
Insert all connectors inside the J-Box.
Using a 5/32” key, tighten the mounting screws to allow the fixture to rest against the wall and level it.

Emergency Option Installation:

Before connecting the power supply, remove the Back plate sub-assembly to access the Emergency driver.
Plug the Converter Connector together and reinstall the Back plate sub-assembly. Apply 12 in-lbs of torque.
Make the supply wiring connections according to the appropriate wiring diagram.
During normal operation, AC power is applied, and the converter connector is closed. The charging indicator light is illuminated, indicating that the battery is being charged. In case of a power failure, the emergency LED driver automatically switches to emergency power (internal battery), operating the LED load for a minimum of 90 minutes. When AC power is restored, the emergency driver returns to charging mode.

FAQ

Q: What should I do if I encounter an irregular surface during installation?

A: In case of an irregular surface, cut extra foam gasket on top/bottom before applying sealant around the Mounting plate.

IMPORTANT: FOR YOUR PROTECTION, YOU MUST CAREFULLY READ ALL WARNINGS AND INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO INSTALLATION, OPERATION, SERVICE OR MAINTENANCE. FAILURE TO DO SO CAN RESULT IN DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. If you do not understand these warnings and instructions, or if additional information is desired, please contact Signify, Gardco. TSC@signify.com phone 1-833-744-6439.

Installation, service and maintenance of luminaires must be performed by a qualified professional and in accordance with all federal, state and local laws, regulations and electrical codes. This professional should be familiar with the construction and operation of this product and any hazards involved. If not qualified, do not attempt installation, service or maintenance.
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts, abrasions and other hazards, please read all warnings and instructions included with the luminaire, on the luminaire’s packaging and affixed to the luminaire itself.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaire’s construction and operation and any hazards involved.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Disconnect or turn off power before attempting any installation, service or maintenance.
Verify that supply voltage is correct by referencing the luminaire label information.
Make all electrical and ground connections in accordance with the National Electrical Code (NEC) and any other applicable laws, regulations or codes.
All wiring connections should be capped with UL-approved wire connectors

WARNING

RISK OF FIRE OR PERSONAL INJURY

Keep combustible materials away from LED/lamp & lens
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source while it is on.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Allow Led/lamp & lens to cool before handling.
Do not touch enclosure or light source
Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations, instructions and restrictions for driver type, burning position, mounting locations and replacement.

CAUTION

RISK OF PRODUCT DAMAGE

Never connect luminaires and/or components under load with supply voltage turned on.
Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation.
Do not restrict fixture ventilation. Allow for some volume of airspace around luminaire. Avoid covering luminaire with insulation, foam or other material that will
prevent convection or conduction cooling.
Do not exceed luminaire maximum ambient temperature.
Do not modify the luminaire.
Only use luminaire in its intended application and location.
Led products are polarity sensitive. Ensure proper polarity before installation.
Electrostatic Discharge (ESD) can damage LED. Personal grounding equipment must be worn during all installation and servicing of the luminaire.
Do not touch individual electrical components as this can cause ESD, shorten LED life, or impact LED performance.
Some components inside the luminaire may not be serviceable. In the unlikely event your luminaire may require service, stop using it immediately and contact
Signify.
Always read the luminaires complete installation instructions prior to installation for any additional luminaire specific warnings.
In the case of HID or Fluorescent luminaires, regular re-lamping is required to keep luminaire operating within safe limits
Do not install damaged product. Handling and installing damaged products can potentially increase the risks mentioned In case of damage and/or missing parts
upon arrival of the luminaire.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation,
operation or maintenance.
Please see luminaire specific Installation and Maintenance Instruction for additional warnings or any applicable FCC or regulatory statements. Failure to follow any of these Instructions could void luminaires warranties.

Luminaire Maintenance

Regular luminaire maintenance programs are recommended.
It is recommended to clean the outside of the luminaire and the refractor/lens.
Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user.
If clean water is not sufficient for cleaning, use a neutral, synthetic, not-scratching and not-abrasive cleaning substance.
Never use alkaline and/or acetous cleaning substances.
Make sure that the cleaning substance is carefully removed by rinsing with lots of clean water.
Signify recommends using a cleaning solution that has a PH between 5 and 8.
Recycle: For information on how to recycle electronic products and components, please visit www.epa.gov.

I/S GEOFORM Installation Instructions

$signify-GCM-Wall-Sconce-FIG $3$$

GCM Wall Mount installation steps

Install the Wall Mount Bracket with gasket to the J Box. Apply 12 in lbs torque until the gasket between wall and Wall Mount Bracket is properly compressed
Notice: In case of irregular surface, cut extra foam gasket on top/ bottom before to apply selant around the Mounting plate.
Make sure the Wall Mount Bracket is properly leveled
Hold the fixture by the 2 hooks to the bottom of Wall Mounting Bracket . Make sure the wire pass in the middle between them
Once luminaire is installed and hardware is properly torqued , make supply wiring connections according to the appropriate wiring diagram.
- 0-10V AND OVERRIDE WIRES OPTIONAL
- WIRE NUTS SUPPLIED BY OTHERS $signify-GCM-Wall-Sconce-FIG $5$$
  GCM Wall Mount installation steps
Insert all connector inside the J Box;
With All Key 5/32’’, tighten the Mounting screws to allow the fixture to rest against the wall & Level it. $signify-GCM-Wall-Sconce-FIG $6$$

Emergency option GWM with BLS36M Cold Pack $signify-GCM-Wall-Sconce-FIG $7$$

Before to connect the power supply, remove the Back plate sub- assembly to get access to the Emergency driver;
Plug the Converter Connecter together and reinstall the Back plate sub-assembly. Apply 12 in-lbs of torque;
Make the supply wiring connections according to the appropriate wiring diagram (page 2);
During normal operation AC power is applied and the converter connector is closed, thecharging indicator light is illuminated, indicating that the battery is being charged. When power fails, the emergency LED driver automatically switches to emergency power (internal battery), operating the LED load for a minimum of 90 minutes. When AC power is restored, the emergency driver returns to the charging mode.

© 2021 Signify Holding. All rights reserved. This document may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. All trademarks are owned by Signify Holding or their respective owners. 12/16/2022 www.gardcolighting.com

Signify North America Corporation