IndiaMART AC110-220V Moving Head Lights User Manual

Moving Head Beam

USER MANUAL

TECHNICAL PARAMETERS

Voltage： AC110-220V, 50-60HZ
Pattern： 8 Patterns
Color： 8 colors, half color effect
Prism: 18 prism
Channel：12CH
Control： Sound, Master-salve, Auto, DMX

LED DISPLAY

1. Menu
2. Up
3. Down
4. Enter
5. Display
6. Dmx in
7. Dmx Out
8. Fuse
9. Switch
10. Power Supply

UNPACKING INSTRUCTIONS

Hen you receive the device, unpack it, check that the contents are complete and intact, notify the carrier immediately if it shows damage, and keep all packing materials for safe transportation of the device.
1 bow support 1lamp
1instruction manual 1 power cord
2 screws (installed on the machine)

SAFETY INSTRUCTIONS AND OPERATING INSTRUCTIONS

After the power is plugged in and the switch is turned on, “rSt” is displayed. The moving headlights are being reset, please do not operate.

1. Plugged into a grounded power outlet for indoor use only.
2. Don’t expose the device to rain or moisture, avoid the risk of fire or electric shock. Make sure that no flammable objects near the device.
3. Install the equipment in a well-ventilated place at least  50cm from any surface, and ensure that the ventilation slots are not blocked.
4. Disconnect the equipment from the power supply before any operation.
5. The ambient temperature should not exceed 40°C, and the maximum ambient temperature is 45°C. Don’t operate the device at higher tempratures.
6. The equipment should be stopped immediately, if a fault occurs, and do not repair the equipment by yourself. Improper maintenance can resultin damage and malfunction. Contact technical support for repair approval. Only the same accessories can be used with the original parts, and make sure the power cord is not blocked ordamaged.
7. Do not expose your eyes to light sources, which can be a sign of a seizure in sensitive people.
8. Thelamps are only used for decoration and not suitable for ordinary household lighting.
9. Replacing the fuse: Unplug the device from the power supply, remove the fuse holder from its original position with a srewdriver, take out the burnt fuse, replace the fuse with the same characteristics, then re-rotate the screw, and connect the device to the power supply superior.
10.   WARNING: Stop using it if the fuse is still blowing after being replaced. Please contact customer support for further instructions, continued use may cause serious damage.

Please read this manual carefully before operating this product.

11.  Fix the equipment with the screw holes on the bracket to ensure that the equipment is firmly fixed to prevent vibration and movement during operation, and always check whether the structure of the equipmentis strong enough to withstand equipment that is at least ten times.
12. The equipment must be fixed by professionals in places that elders and children cannot reach, and no one can pass under or over the pedestrian crossing.
13.  End-of-life of the product: This sign indicates that this product should not be thrown into household waste in European Community countries and that waste should be recycled to support the sustainable recycling of resources in order to protect the environment and human health Utilize. If you need to recycle used electrical appliances, please gotoan electrical appliance collection center or contact the dealer where you purchased the product to ensure the ecological recycling of the product.
    Remote Control : If you want to control the light by remote, please unplug the DMX cable and set Remote Control to ON. If you want to control the device via the menu, set the remote to off.

STARTUP STEPS FOR VARIOUS MODES

1.  Automatic mode
   Press “menu” to find “SLND”, press “enter”, press “up” or “down” to select “AUTO”, and press “enter” to start.

2.  Sound mode:
   Press “menu” to find “SLND”, press “enter”, press “up” or “down” to select “soun”, and press “enter” to start. Adjust the sound sensitivity. Press “enter” to find “sene”.
   Press “up” or “down” to start the speed of sound sensitivity (the higher the value, the faster, and the lower the value, the slower)

3. Console mode and master-slave mode:
   DMX out to 1 lamp dmxin; No.1 lamp DMX out is connected to No.2 lamp dmxin; Press “menu” to find “addr”, press “enter”, display “A001”, press “up” or “down” to select the value of the console; Setting of master-slave machine: No. 1 lamp is set as self-propelled or voice control function according to the starting mode;2, 3, 4 set to DMX512 mode: DMX address code is 001

SPEISEKARTE

| | DMX Mode
| Auto Mode
| Sound Mode
| | X-axis, forward/reverse
| | Y-axis, forward/reverse
| | Adjust the sensitivity of sound
| | Display screen on/off
| | Display screen forward/reverse
| | Display temperature
| | Software version number
| | Maintain Settings
| System Reset

CHANNEL

slow
198-255| Color disc reversal, speed from slow to fast
9| Pattern Plate| 0-9| Circular pattern
---|---|---|---
10-79| Pattern  1-7 selection
80-149| Pattern   jitter selection, slow to fast speed
150-159| Circular pattern  jitter,  slow to fast speed
160-207| Automatic clockwisecolor switching from fast to slow
208-255| Automatic  Counterclockwise  color switching from fast to slow color switching from fast to slow
10| Prism| 0-8| Close Prism
9-127| Open Prism
| | 128-255| Prism rotation from slow to fast
11| Self driving/voice| 0-50| Other channels are effective
51-100| Fast self-propelled
101-200| Slow self-propelled
201-255| Sound Mode
12| Reset| 0-249| No function
250-255| Lamp body reset,3s effective.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>