HYUNDAI 2024 Santa Fe Mudguard Kit

Specifications

• Vehicle Model: Santa Fe
• Accessory: Mudguard Kit
• Model Year: 2024~
• Part No.: R6F46 AC000
• Language: English
• Revision Date: 3/13/2024
• Part Weight (Gross): 0.82 lbs / 0.37 kg

Product Usage Instructions

Installation Instructions
Before beginning the installation, ensure you have the latest revision of the installation instructions. You can do this by scanning the QR code provided or by visiting the website mentioned in the manual.

Difficulty Level
The installation difficulty level is indicated as (B), suitable for a Dealer Technician.

Required Tools

• Clip Removal Tool

• 2 Phillips Right-Angle Driver

• Electric Drill

Notes to Installer

1. Read the entire Installation Instructions before starting the installation.
2. If applicable, scan the barcode label on the accessory part for registration.
3. Ensure the vehicle is clean and dry in the installation area.
4. Protect the vehicle in the installation area.
5. Avoid placing tools on sensitive surfaces like painted areas or seating surfaces.
6. Always wear appropriate personal protective equipment when required.

Kit Overview

Frequently Asked Questions (FAQ)

• Q: Can I install the mudguards without professional help?
  

  • A: The installation difficulty level is suitable for a Dealer Technician, but if you have experience with similar installations and follow the instructions carefully, you may be able to install them yourself.

• Q: Do I need to register the part after installation?
  

  • A: It is recommended to scan the barcode label on the accessory part for registration after installation, especially if replacing an existing part.

Genuine Accessories

• Vehicle Model : Santa Fe
• Model Year  2024~
• Part No. R6F46 AC000
• Language English
• Rev. Date 3/13/2024

Accessory: Mudguard Kit

• Difficulty: ( B )

Note: Difficulty stated above reflects the minimum level of expertise required to install the accessory

• Customer
• Dealer Technician
• Master Technician or Specialist

Electronic Installation Instructions

If this is a printed copy of the installation instructions, ensure you have the latest revision by scanning the QR code or by entering the website address listed below before beginning installation. Use the latest revision date as noted by “Rev. Date” above.

www.hyundaiaccessories.com/admin_media_uploads/installationSheets/r6f46_ac000.pdf

Instructional Symbols / Definitions

Denotes warnings that may lead to serious physical injury or vehicle damage
Denotes cautions to be taken to avoid physical injury or electronic component damage
Denotes cautions to be taken to avoid vehicle and component damage

Denotes quality processes to be checked prior to moving to the next step

Denotes specific tools that are necessary to complete a step

Denotes important information to be reviewed during the step

Denotes personal protective equipment (PPEs) that may be required for a step. Examples of safety equipment icons noted below:

FMVSS 110 Compliance Information
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories.

Load Label Part Number: NP070 – 09003

Notes to the installer

1. Read the entire Installation Instructions prior to beginning the installation of the part.
2. If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old registration cannot be reused.
3. Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
4. Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
5. NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
6. Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.

Genuine Accessories

Kit Overview

Hardware Kit Contents

Hardware Kit Total

20
1| **| Clip Removal Tool
---|---|---
N O T E| NOTE:** Fully turn the steering wheel to the left when installing the driver’s side front mudguard (LH) and fully turn the steering wheel to the right when installing the passenger’s side front mudguard (RH).

• Starting on the driver’s side front wheel well area, remove the two (2) plastic retainers as shown.
• Discard the removed hardware.

|
2| |
---|---|---
N O T E| A. Insert two (2) locking retainers into the two (2) holes as shown above and press inward firmly.
****| Ensure the locking retainers are fully inserted.
3| **|
---|---|---
N O T E| A. Align the driver’s side front mudguard (LH) as shown ensuring a proper fit.
| Make sure to push the mudguard upward and inward during the installation to eliminate any possible gaps.
4| **|
---|---|---
N O T E| A. Insert one (1) provided plastic retainer into the bottom hole as shown. Make sure to push in the center portion of the plastic retainer to lock the retainer in place.
**| Make sure to push the mudguard upward and inward during the installation to eliminate any possible gaps.
5| **| #2 Phillips Right-Angle Driver and Electric Drill
---|---|---
N O T E| NOTE: The screws and locking retainers will begin to rotate together once the screws have bottomed out. Only fasten the screws until they have bottomed out.

• While pushing the mudguard upward and inward as shown, insert and fasten one (1) provided screw into the upper hole “A” as shown.
• Insert and fasten one (1) provided screw into the lower hole “B” as shown.
• Repeat steps 1-5 for passenger’s side front mudguard (RH).

****| Check for any visible gaps. If any gaps exceed 0.5mm, loosen the mounting hardware and refit the mudguard to the body to decrease or eliminate the gaps. Do not to over-tighten or strip the screws.
6| **| Clip Removal Tool**
---|---|---

N O T E

|

• On the driver’s side rear wheel well area, remove the one (1) top plastic retainer as shown above.
• Remove one (1) bottom plastic retainer as shown above.
• Discard the removed hardware.

|
7| ****|
---|---|---
N O T E|

• Carefully pull back the felt wheel liner and insert two (2) locking retainers into the two (2) holes of the lower bumper tabs as shown above.
• Reseat the felt wheel liner back into orginal location.

****| Ensure the locking retainers are fully inserted.
8| **| #2 Phillips Right-Angle Driver and Electric Drill**
---|---|---
N O T E|

• Align the rear mudguard (LH) as shown ensuring a proper fit.

• Insert one (1) provided plastic retainer into the bottom hole as shown. NOTE : The screws and locking retainers will begin to rotate together once the screws have bottomed out in the following procedure. Only fasten the screws until they have bottomed out.

• While pushing the mudguard upward and inward as shown, insert and fasten one (1) provided screw into the upper hole “C” as shown.

• Insert and fasten one (1) provided screw into the lower hole “D” through the felt wheel liner and into the locking retainer as shown.
  NOTE : Make sure screw is straight when installing through felt material.

• Repeat steps 6-8 for passenger’s side rear mudguard (RH).

**| Check for any visible gaps. If any gaps exceed 0.5mm, loosen the mounting hardware and refit the mudguard(s) to the body to decrease or eliminate the gaps. Do not to over-tighten or strip the screws.
Visual Check**

Item to be Checked

| Make sure to push the Front and Rear Mudguards upward and inward during the installation to eliminate any possible gaps.
---|---
****| Check for any visible gaps.

If any gaps exceed 0.5mm, loosen the mounting hardware and refit the Mudguard(s) to the body to decrease or eliminate the gaps.

Result

Front and Rear Mudguards are properly aligned.|
---|---
Any visible gaps do not exceed 0.5mm.|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>