AVer PTC310UV2 AI Auto Tracking PTZ Camera Instruction Manual

: June 9, 2024
: AVer

Table of Contents

AVer PTC310UV2 AI Auto Tracking PTZ Camera
Product Introduction
RS232 mini DIN9 to mini DIN8 Cable Pin Definition
OSD Tree
Visca-over-IP Settings
CGI Command Table
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AVer PTC310UV2 AI Auto Tracking PTZ Camera

Product Introduction

Overview

(1) Tally Lamp	(5) PoE+ IEEE 802.3AT	(9) Audio In*
(2) IR Sensor	(6) RS-232 Port	(10) HDMI Port
(3) LED Indicator	(7) RS-422 Port	(11) 3G-SDI**
(4) Kensington Lock	(8) USB 3.0 Port (Type-B)	(12) DC Power Jack

Line input level: 1Vrms (max.).
Mic input level: 50mVrms (max.);
Supplied voltage: 2.5V.
The model names with “H” do not have this feature.

RS232

RS232 Port Pin Definition

Function

| Mini DIN9 PIN #| ****

I/O Type

| ****

Signal

| ****

Description

---|---|---|---|---

VISCA IN

VISCA OUT

| 7| Output| DTR| Data Terminal Ready
4| Input| DSR| Data Set Ready
8| Output| TXD| Transmit Data
9| Input| RXD| Receiver Data
5| —| —| Not connect

RS232 mini DIN9 to mini DIN8 Cable Pin Definition

Mini DIN8 Cable Pin Definition

No.	Signal
1	DTR
2	DSR
3	TXD
4	GND
5	RXD
6	GND
7	NC
8	NC

Din8 to D-Sub9 Cable Pin Definition

RS422

[Note] Use cat5e splitter for multi-camera connection.

RS422 Pin

No.| Pin| No.| Pin
1| TX-| 5| TX+
2| TX+| 6| RX+
3| RX-| 7| RX-
4| TX-| 8| RX+

Cat5e splitter pin assignment: AVer-PTC310UV2-AI-Auto-Tracking-PTZ-
Camera-FIG-10

OSD Tree

Advanced Setting
Go to Advanced Setting -> Control. Make sure the Camera Address, Baud Rate setting is correct.

1st Layer	2nd Layer	3rd Layer	4th Layer
Advanced Setting	Audio	Input Type	Line In

P/AW

RS232/422 Visca Command Table

Command Set	Command	Command Packet	Comments
CAM_Power	On	8x 01 04 00 02 FF	Power ON/OFF
Off	8x 01 04 00 03 FF

CAM_Zoom

Direct

|

8x 01 04 47 0p 0q 0r 0s FF

| pqrs: Zoom Position， PTC310: 0x0000~0x6f20 PTC330: 0x0110~0x5490

CAM_Focus

CAM_WB

| Auto| 8x 01 04 35 00 FF| Normal Auto
ATW| 8x 01 04 35 04 FF|
Indoor| 8x 01 04 35 01 FF|
Outdoor| 8x 01 04 35 02 FF|
One Push WB| 8x 01 04 35 03 FF| One Push WB mode
Manual| 8x 01 04 35 05 FF| Manual Control mode
One Push| 8x 01 04 10 05 FF| One Push WB Trigger
CAM_RGain| Up| 8x 01 04 03 02 FF| Manual Control of R Gain
Down| 8x 01 04 03 03 FF|
CAM_Bgain| Up| 8x 01 04 04 02 FF| Manual Control of B Gain
Down| 8x 01 04 04 03 FF|

CAM_AE

CAM_Preset

| Reset| 8x 01 04 3F 00 pp FF|

pp: Preset Number 0x00~0xFF

Pan-tilt Drive

| Up| 8x 01 06 01 VV WW 03 01 FF|

VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed) WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed)

Freeze

CAM_Memory Special

|

Set

|

8x 01 04 3F 01 pp FF

| pp: 0x00 To 0xFF normal preset pp: 0x5F => Trun on OSD menu pp: 0xA0 => Full Body

pp: 0xA1 => Upper Body pp: 0xA2 => Tracking Point pp: 0xA3 => Switch

pp: 0xA4 => Presenter mode (supported in FW v25 or newer) pp: 0xA5 => Zone mode (supported in FW v25 or newer)

pp: 0xA6 => Hybrid mode (supported in FW v35 or newer)

Absolute Position

|

Set

|

8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

| VV: Pan speed setting 0x01 (low speed) to 0x18 (high speed) WW: Tilt speed setting 0x01 (low speed) to 0x18 (high speed) YYYY: Pan Position

ZZZZ: Tilt Position

Auto zoom

| On| 8x 01 04 A0 02 FF|
Off| 8x 01 04 A0 03 FF|

Effective Tracking area

| On| 8x 01 04 A1 02 FF|
Off| 8x 01 04 A1 03 FF|

RTMP

| On| 8x 01 04 A2 02 FF|
Off| 8x 01 04 A2 03 FF|

Video mode

Preset Affects PTZ & Focus

|

On

|

8x 01 04 A5 02 FF

|
Off| 8x 01 04 A5 03 FF|

Relative Zoom Ratio

| On| 8x 01 04 A6 02 FF|
Off| 8x 01 04 A6 03 FF|

Auto Tilt

| On| 8x 01 04 A7 02 FF|
Off| 8x 01 04 A7 03 FF|
Auto Zoom/Tilt preset| Set| 8x 01 04 A8 pp FF| pp: 0x00 To 0xFF normal preset
Inquiry Command| Command Packet| Reply Packet| Comments
---|---|---|---
CAM_PowerInq| 8x 09 04 00 FF| y0 50 02 FF| On
y0 50 03 FF| Off

CAM_WBModeInq

|

8x 09 04 35 FF

CAM_AEModeInq

|

8x 09 04 39 FF

ZZZZ: Tilt Position

CAM_Tracking_mode

|

8x 09 36 69 01 FF

The x value = VISCA Camera ID: 1 to 7 for RS232/RS422 connection

Visca-over-IP Settings

AVer-PTC310UV2-AI-Auto-Tracking-PTZ-Camera-
FIG-11

The x value of 8x should be 1 for Visca-over-IP string.
Example for Pan-Left command via IP: 01 00 00 09 00 00 00 01 81 01 06 01 07 07 01 03 FF

CGI Command Table

CGI List for Video Transmission

CGI item name| URL| Command| Parameter Name| Parameter value| Description
Get JPEG| /snapshot| | | | 1280×720 jpg
Get RTSP stream| rtsp://ip/live_st1| | | |
| | | | |
CGI List for Camera Control
CGI item name| URL| Command| Parameter Name| Parameter value| Description
up start| /cgi-bin?SetPtzf=| 1,0,1&(random)| | |
up end| /cgi-bin?SetPtzf=| 1,0,2&(random)| | |
down start| /cgi-bin?SetPtzf=| 1,1,1&(random)| | |
down end| /cgi-bin?SetPtzf=| 1,1,2&(random)| | |
left start| /cgi-bin?SetPtzf=| 0,1,1&(random)| | |
left end| /cgi-bin?SetPtzf=| 0,1,2&(random)| | |
right start| /cgi-bin?SetPtzf=| 0,0,1&(random)| | |
right end| /cgi-bin?SetPtzf=| 0,0,2&(random)| | |
zoom_in start| /cgi-bin?SetPtzf=| 2,0,1&(random)| | |
zoom_in end| /cgi-bin?SetPtzf=| 2,0,2&(random)| | |
zoom_out start| /cgi-bin?SetPtzf=| 2,1,1&(random)| | |
zoom_out end| /cgi-bin?SetPtzf=| 2,1,2&(random)| | |
set preset:| /cgi-bin?ActPreset=| 1,N&(random)| | | N : position
load preset:| /cgi-bin?ActPreset=| 0,N&(random)| | | N : position
set preset speed| /cgi-bin?Set=preset_speed,3,val| val: {min: 1, max: 6}| | |
Absolute Position (Pan)| /cgi-bin?Set=ptz_p,3,val| val: {min: 2048, mid: 962944, max: 1925888}| | | Follows CGI preset speed
Absolute Position (Tilt)| /cgi-bin?Set=ptz_t,3,val| val: {min: 2048, mid: 165696, max: 662784}| | | Follows CGI preset speed
(Zoom)| /cgi-bin?Set=ptz_z,3,val| val: {min: 2048, mid: 14224, max: 28448}| | | Follows CGI preset speed
| | | | |
| | | | |
CGI List for Various Settings
exposure value| /cgi-bin?Set=| img_expo_expo,3,N&(random)| value| 1 ~ 9| N : value
saturation| /cgi-bin?Set=| img_saturation,3,N&(random)| value| 0 ~ 10| N : value
contrast| /cgi-bin?Set=| img_contrast,3,N&(random)| value| 0 ~ 4| N : value
Tracking on:| /cgi-bin?Set=| trk_tracking_on,3,1| | |
Tracking off:| /cgi-bin?Set=| trk_tracking_on,3,0| | |
Reboot| GET(Basic Authentication)| /cgi-bin?OnePush=!| | |
Factory Reset| GET(Basic Authentication)| /cgi-bin?OnePush=d| | |
Mode Presenter| | /cgi-bin?Set=trk_mode,3,1&X| value| random number| X : value
Mode Zone| | /cgi-bin?Set=trk_mode,3,2&X| value| random number| X : value
Mode Hybrid| | /cgi-bin?Set=trk_mode,3,3&X| | |

Mode Get

|

GET(Basic Authentication)

|

/cgi-bin?Get=trkmode,3&=X

|

– Reply

| Presenter trk_mode,3=1 Zone trk_mode,3=2 Hybrid trk_mode,3=3|

X : value

Get detect zone (Humanoid outlines) number

Click Track ON command

– Reply

|

“trk_detect_num,3=X\r\n”

| X: The amount of humanoid outlines, maximum: 50| |

Click Track

Get detect zone (Humanoid outlines) info

|

GET(Basic Authentication)

|

/cgi-bin?GetTrackingDetectZone=X

| X: The amount of humanoid outlines, maximum: 50| |

– Reply

|

“focus:-1\nzone[00]:00,119,720,960\nzone[01]:- 1502615204,-1366225632,01,-1366223544”

|

focus – The number of humanoid outline being tracked. zone[NN]:x,y,w,h – based on 1080P resolution

| The upper left corner of the screen is the coordinate reference (0,0), x-coordinate/y-coordinate/w width/h height, based on the upper left corner of the humanoid outline.

The number following indicates the number of the tracked person, for example, -1 means that no one is being tracked. If one of the three is being tracked,

one of 0, 1 and 2 will appear after the ‘focus’.

|

Click Track Set target zone

Tracking On/Off Get

|

GET(Basic Authentication)

|

/cgi-bin?Get=trk_trackingon,3&=X

|

– Reply

| On trk_tracking_on,3=1 Off trk_tracking_on,3=0″|

X : value