Speed Queen D517569 White Front Load Electric Dryer User Manual
- June 5, 2024
- Speed Queen
Table of Contents
D517569 White Front Load Electric Dryer
User Manual
Welcome
Welcome to the Speed Queen® family. Thank you for your support of our truly commercial quality products. Our washers and dryers are expertly engineered to deliver commercial performance, tested to ensure ultimate durability and built with American Pride. For more than 110 years, Speed Queen consumer laundry products have been manufactured in Ripon, Wisconsin, a place where pride of workmanship is not just alive, but thriving and embodied by each individual who designs, tests, assembles or in some way touches a Speed Queen product. A special thing happens when that pride is combined with the highest quality commercial materials and components…it leads to the ultimate reliability…reliability measured in decades, not years. That’s legendary Speed Queen Quality.
Installation
Parts included:
1. Position and level the dryer.
- Recommended rear clearance minimum is 2 in (51 mm) for utility connections and 6 in (152 mm) when venting through rear of unit
2. Connect exhaust system.
-
Dryer must be exhausted to the outdoors
-
Use 4 in (102 mm) rigid duct
-
Maximum straight duct length = 65 ft
(19.8 m). Each elbow deduct 10 ft (3 m) -
Sufficient make-up air must be supplied. The free area of any opening for outside air must be at least 40 in2 (25806 mm2) per unit
3. Gas models – connect gas supply pipe.
Gas service to a gas dryer must conform with the local codes and ordinances.
Refer to installation instructions, which can be found at speedqueendoc.net
- Tighten all connections securely but do not overtighten to avoid breaking or bending the gas valve bracket.
Turn on gas and check all pipe connections (internal and external) for gas leaks by applying a non-corrosive leak detection fluid to the fittings. If bubbles are present then a leak is likely.
Retighten connections and recheck for leaks.
4. Electric models – connect electrical cord with three-wire or four-
wire plug.
Refer to installation instructions, which can be found at speedqueendoc.net
5. Wipe out inside of dryer.
6. Plug in the dryer.
7. Start dryer and check that dryer is heating.
Cycle Information
Electronic Control Dryers
The following cycle descriptions will help determine which cycle to choose
depending on the type of laundry being dried. The cycle settings may be
modified using the Selections and Options.
Auto-Sensing
The Auto-Sensing drying cycle operation is determined by the type of cycle
selected as well as the moisture sensing system, which can be set by changing
the Dryness setting. Auto-Sensing cycles are Energy Saver cycles that help
prevent over-drying. When a wet load is put into the dryer it takes a certain
amount of time to reach the desired dryness level. The time will vary with
load size, type of fabric, amount of moisture in the load, air flow and the
laundry room environment. The estimated time will be shown in the digital
display.
Note: The time shown before starting the cycle is estimated by averaging the last 5 cycles run on the selected cycle/dryness combination.
The Favorite Cycle
The Favorite keypad allows the user to save nine different cycles, selections and options for later use.
- Press the Favorite keypad. The control will display the settings for the first Favorite cycle. The display will switch between F1 and the cycle time for the selected cycle.
- Press the keypads for the desired settings.
- Press the Favorite keypad to save the settings.
- The next Favorite cycle, F2, will be displayed. Access saved Favorite cycles by pressing Favorite keypad and then the up and down arrow keypads.
Manual
There are three manual cycles: Time Dry, Quick Dry and Fluff Up. These cycles
will run for the set number of minutes shown on the digital display. The cycle
time can be increased or decreased using the up and down arrow keypads. The
time and temperature selection may be adjusted manually at any time before or
during the cycle.
Operating
Register
1. Register your product at www.speedqueen.com to take full advantage of the limited warranty.
3, 5 & 7 Year Warranties, depending on your model. Covers all parts and in- home labor.
Note: This unit includes a limited warranty. Refer to Speedqueendoc.net to download the full warranty bond.
2. Download full documentation and view installation and operating videos for an immersive experience at Speedqueendoc.net or scan the QR code below.
3. If you wish to receive printed documents at no cost, please complete the
order form online at speedqueen.com/request-printed-
documents/or email your
request to technicalcommunications@alliancels.com.
If you don’t have internet access, complete the attached order form and return
by mail to the address on the form.
Order Form for Printed Documentation
As an alternative to mailing this card, and for faster delivery of your manuals, place your order online at speedqueen.com/request-printed- documents/.
☐ Please send me a printed Installation Manual, User’s Guide, and Warranty
Bond.
☐ I understand this card does not register my product. I must go to
www.speedqueen.com to register.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>