SUNRICHER SR-ZG9032A Zigbee 4 in 1 Multi Sensor Owner’s Manual
- July 16, 2024
- SUNRICHER
Table of Contents
SUNRICHER SR-ZG9032A Zigbee 4 in 1 Multi Sensor
Features
Key Features
- Zigbee 3.0 compliant
- PIR motion sensor, long detection range
- Temperature sensing, automates your home heating or cooling
- Humidity sensing, automates your home humidifying or dehumidifying
- Illuminance measuring, daylight harvesting
- Autonomous sensor-based control
- OTA firmware upgrade
- Wall mount installation
- Can be use for indoor applications
Benefits
- Cost-effective solution for energy savings
- Energy code compliance
- Robust mesh network
- Compatible with universal Zigbee platforms that support sensor
Applications
- Smart home
Product Description
The Zig bee sensor is a battery powered low power consumption 4 in 1 device that combines PIR motion sensor, temperature sensor, humidity sensor, and illuminance sensor. The PIR motion sensor trigger and sensitivity can be configured. The sensor supports low battery power alarm, if the power is lower than 5%, the motion sensor trigger and report will be forbidden, and the alarm will be reported every one hour until the battery power is higher than 5%. The sensor is suitable for smart home applications which need sensor based automation.
Commissioning
All setup is performed via supported IEEE 802.15.4-based control platforms and
other Zigbee3.0 compatible lighting control systems. Appropriate gateway
control software allows for adjustment of motion sensitivity, detection area,
time delay and daylight threshold.
Product Info
With Frame
Parameters
Physical Information
- Dimensions 55.555.523. 7mm
- Material / Color ABS/White
Electrical Information
- Operate Voltage 3VDC (2*AAA Batteries)
- Standby Consumption 10uA
Wireless Communication
- Radio Frequency 2.4 GHz
- Wireless Protocol Zigbee 3.0
- Wireless Range 100 feet (30m) Line of Sight
- Radio Certification CE
Sensing
- Motion Sensor Type PIR sensor
- PIR sensor Detection Range Max. 7 meters
- Recommended Installation Height Wall mount, 2.4 meters
- Temperature Range and Precision -40°C-+125°C, ±0.1 °C
- Humidity Range and Precision 0- 100% RH (non-condensing), ±3%
- Illuminance Measuring Range 0~10000 Iux
Environment
- Operating Temperature Range 32° F to 104° F / 0°C to 40°C (indoor use only)
- Operating Humidity 0-95% (non condensing)
- Waterproof Rating IP20
- Safety Certification CE
LED Indicator Status
- Operation Description LED Status
- Pl R motion sensor triggered Flashing once rapidly
- Powered on Staying solid on for 1 second
- OTA firmware update Flashing twice rapidly with 1 second interval
- Identify Flashing slowly (0.5S)
- Joining a network (Triple press the button) Flashing rapidly continuously
- Joined successfully Staying solid on for 3 seconds
- Leaving a network or reset (Long press the button) Flashing slowly (0.5S)
- Already in a network (Short press the button) Staying solid on for 3 seconds
- Not in any network (Short press the button) Flashing three times slowly (0.5S)
Operation
Zigbee Network Pairing
Step 1: Remove the device from previous zig bee network if it has already
been added to, otherwise pairing will fail. Please refer to the part “Factory
Reset Manually”.
Step 2: From your ZigBee gateway or hub interface, choose to add device
and enter Pairing mode as instructed by the gateway.
Step 3: Method 1: short press the “Prog.” Button 3 times continuously
within 1.5 seconds, the LED indicator will flash rapidly and enter into
network pairing mode (beacon request) which lasts for 60 seconds. Once
timeout, repeat this step.
Method 2: make sure the device has not paired to any Zigbee network,
reset power of the device by removing the batteries and installing them again,
then the device will enter into network pairing mode automatically which lasts
for 10 seconds. Once timeout, repeat this step.
Step 4: The LED indicator will stay solid on for 3 seconds if the device
is paired to the network successfully, then the device will appear in your
gateway’s menu and can be controlled through gateway or hub interface.
Removing from a Zigbee Network
Press and hold the Prog. button until LED indicator blinks 4 times slowly,
then release the button, LED indicator will then stay solid on for 3 seconds
to indicate that the device is removed from the network successfully.
Note: the device will be removed from the network and all bindings will
be cleared.
Factory Reset Manually
Press and hold the Prog. button for over 10 seconds, during the process, the
LED indicator will blink slowly at the frequency of 0.5Hz, the LED indicator
will stay solid on for 3 seconds which means factory reset successfully, then
LED will turn off.
Note: factory reset will remove the device from the network, clear all
bindings, restore all parameters to factory default setting, clear all report
config settings.
Check Whether the Device is Already in a Zigbee Network
Method 1: short press Prog. button, if LED indicator stays solid on for 3
seconds, this means the device has already been added to a network. If LED
indicator blinks 3 times slowly, this means the device has not been added to
any network.
Method 2: reset power of the device by removing the batteries and
installing them again, if the LED indicator blinks rapidly, it means the
device has not been added to any network. If LED indicator stays solid on for
3 seconds, this means the device has not been added to any network.
Wireless Data Interaction
Since the device is a sleep device, it needs to be awakened.
If the device has already been added to a network, when there is a button
trigger, the device will be awakened, then if there is no data from the
gateway within 3 seconds, the device will go to sleep again.
Zigbee Interface
Zigbee application endpoints:
Application Endpoint #0 Zig Bee Device Object
- Application profile Id 0x0000
- Application device Id 0x0000
- Supports all mandatory clusters
Application Endpoint #1 -Occupancy Sensor
Basic -OxOOOO (Server)
Attributes Supported:
Command supported:
Power Configuration-0x0001 (Server)
Attributes Supported:
Identify-Ox0003 (Server)
Attributes Supported:
Sever can receive the following commands:
Sever can generate the following commands:
| CmdlD | Description |
|---|---|
| OxOO | Identify Query Response |
OTA Upgrade-Ox0019 (Client)
When the device has joined a network it will automatically auto scan for a OTA
upgrade server in the network. If it finds a server an auto bind is created
and ones every 10mins it will automatically send its “current file version” to
the OTA upgrade server. It is the server that initiates the firmware upgrade
process.
Attributes Supported:
Occupancy Sensing-0x0406(Server)
Attributes Supported:
Proprietary Attributes:
Alarm-0x0009(Server)
Please set a valid value of Battery Alarm Mask of Power Configuration.
The Alarm Server cluster can generate the following commands:
Power Configuration, alarm code: 0x10.
Battery Voltage MinThreshold or Battery Percentage MinThreshold reached for
Battery Source
Application Endpoint #3 IAS Zone
IAS Zone-0x0500(Server)
Attributes Supported:
The IAS Zone Server cluster can generate the following commands:
The IAS Zone Server cluster can receive the following commands:
Application Endpoint #3 Temperature Sensor
Temperature Measurement-0x0402 (Server)
Attributes Supported:
Proprietary Attributes:
Application Endpoint #4 Humidity Sensor
Relative Humidity Measurement-0x0405 (Server)
Attributes Supported:
Proprietary Attributes:
Application Endpoint #5 Light Sensor
Illuminance Measurement-0x0400 (Server)
Attributes Supported:
Detection Range
Detection range of the Motion Sensor is shown below. Actual range of the Sensor can be influenced by environmental conditions.
Physical Installation
Method 1 : Stick 3M glue on the back of the bracket and then stick the
bracket to the wall
Method 2: Screw the bracket to the wall
After the bracket is fixed . clip the frame and control part to the bracket in
sequence
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>