VIVO STAND-V001LF Laptop Tray And Desk Mount with RGB Fan Instruction Manual
- July 16, 2024
- Vivo
Table of Contents
VIVO STAND-V001LF Laptop Tray And Desk Mount with RGB Fan Instruction
Manual
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v001lf
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com Chat live with an agent!
309-278-5303
WARNING
If you do not understand these directions, or if you have any doubts about
the safety of the installation,
please contact our product support team at
309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are
no missing or defective parts. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly
specified in this manual. Do not exceed weight capacity. We cannot be liable
for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS
REQUIRED.
TIP OVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIP OVER. TO HELP PREVENT
TIP OVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIP OVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIP OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury
Laptop
Monitor
TOOLS NEEDED
PACKAGE CONTENTS
-
A (x1) Pole
-
B (x1) Clamp
-
C (x1) Arm
-
D (x1) VASE Plate”
-
E (x1) Laptop Tray
-
F (x1) Grommet Base
-
G (x1) Soft Pad
-
H (x2) Arm Cable Clip
-
I (x1) Pole Cable Clip
-
J (x1) Pole Cap
-
K (x2) Laptop Arm
-
L (x2) Latch
-
S-A (x3) M6x16mm Screw
-
S-B (x1) M6 Nut
-
S-C (x4) M4x12mm Screw
-
M-A (x4) M4x12mm Thumbscrew
-
M-B (x4) M4x30mm Screw
-
M-C (x4) M4 Spacer
-
M-D (x4) M5 Washer
-
T-A (x1) 3mm Allen Wrench
-
T-B (x1) 5mm Allen Wrench
NOTE : SOME HARDWARE INCLUDED MAY NOT BE USED
ASSEMBLY STEPS
STEP 1
Loosen the knob on Clamp (B).
STEP 2 (Option A)
Desk Clamp Install
Loosen Clamp Bolt (B1) on Clamp (B). Install Clamp (B) to Pole
(A) using M6x16 Screws (S-A) and 3mm Allen Wrench (T-A).
Secure the clamp assembly to the desktop.
STEP 2 (Option B)
Grommet Install
Using a Phillips screwdriver, remove the screw from Clamp (B) and separate
Clamp Bolt (B1) and Clamp Plate (B2) from the clamp assembly. Thread
Clamp Plate (B2) onto B lamp Bolt (B1).
Install Grommet Base (F) to Pole (A) using M6x16mm Screws (S-A)
and 3mm.
Allen Wrench (T-A). Remove adhesive backing from Soft Pad (G) and
stick it to the bottom of Grommet Base (F).
If not using an existing through-hole for mounting, use a 3/8” (10mm) drill
bit to create a mounting hole in the desired location. Thread Clamp Bolt
(B1) with Clamp Plate (B2) through the mounting hole and into Pole
(A).
STEP 3
Slide Pole Cable Clip (I) and Arm (C) over Pole (A). Secure Arm
(C) at the desired height using 5mm Allen Wrench (T-B). Insert Pole
Cap (J) into the top of Pole (A).
STEP 4
Attach Arm Cable Clips (H) to Arm (C).
STEP 5
Install Laptop Arms (K) onto the Laptop Tray (E) using Latches
(L). Lay Latches (L) over the Laptop Tray (E) with one set of the
hooks aligned with the slot on the tray and the other offset from the edge of
the tray. Press the hooks on Latches (L) into Laptop Arms (K).
STEP 6
Install the Laptop Tray (E) to VESA Plate (D) using the M4x12mm Screws
(S-C) and M5 Washers (M-D). Tighten the screws using a Phillips
screwdriver.
STEP 7
Slide VESA Plate (D) onto Arm (C) and secure using M6 Nut (S-B).
STEP 8
Adjust the Laptop Tray (E) size by pulling down the levers on Laptop Arms
(K). Adjust the arms to your
desired width and press the levers back in to secure. Plug the USB-A cable
into any 5V power supply to power the fan and RGB lighting.
OPTIONAL USE: MONITOR MOUNT
To use stand as single monitor mount, follow Steps 1-4, then return to these instructions to proceed.
STEP 5
Attach VESA Plate (D) to the back of the monitor using M4x12mm Thumbscrews
(M-A) or M4x30mm Screws (M-B) with M4 Spacers (M-C).
Slide VESA Plate (D) with the monitor onto Arm (C). Secure the assembly in
place using M6 Nut (S-B).
STEP 6
Manage cables using Arm Cable Clips (H) and Pole Cable Clip (I).
STEP 7
Adjust the tilt using 5mm Allen Wrench **(T-B).
**
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>