VIVO STAND-V202T Dual Ultrawide Vertical Monitor Desk Mount Instruction Manual

: July 2, 2024
: Vivo

Table of Contents

VIVO STAND-V202T Dual Ultrawide Vertical Monitor Desk Moun
Product Usage Instructions
Package Contents
Included Hardware & Tools
ASSEMBLY STEPS
Adjust as Desired
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIVO STAND-V202T Dual Ultrawide Vertical Monitor Desk Moun

Specifications

Product: Dual Ultrawide Vertical Monitor Desk Mount
SKU: STAND-V202T
Weight Capacity: 4.4-44lbs (2-20kg)

Product Usage Instructions

Package Contents

A (x1) Base
B (x2) Arm

Included Hardware & Tools

S-A (x4) Wing Nut

Tools Needed:
Phillips Screwdriver

Assembly Steps

STEP 1a Option A – Clamp
Connect Clamp Brace (K) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A).

STEP 1b Option B – Grommet
Attach Grommet Plate (H) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A).

FAQ

Q: What is the weight capacity of the Dual Ultrawide Vertical Monitor Desk Mount?
A: The weight capacity is 4.4-44lbs (2-20kg).
Q: How do I contact customer support for this product?
A: You can call us at 309-278-5303, chat with us on our website, or email us at [email protected].
Q: What should I do if I don’t have a grommet hole for installation?
A: If you do not have an existing hole for installation, drill a hole through your desktop in your desired mounting location using a0.375 (10mm) drill bit.

Dual Ultrawide Vertical Monitor Desk Mount
SKU: STAND-V202T
Instruction Manual

Assembly Video & Product Info
www.vivo-us.com/products/stand-v202t

CAUTION!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo- us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

We’re Here for You
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Give us a Call: 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
Chat Us: www.vivo-us.com AVG. RESOLUTION TIME (within office hrs): < 15 M
Email Us: [email protected] AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr

Package Contents

Included Hardware & Tools

Tools Needed:

Weight Capacity:

ASSEMBLY STEPS

STEP 1a
Option A – Clamp
Connect Clamp Brace (K) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A).

Remove protective film from Soft Pad (I) and apply to the underside of Clamp Brace (K).
Loosen the screws on the back of Lower Clamp (L) using 4mm Allen Wrench (T-A), leaving 6mm of thread exposed.

0.4” to 2.25” (10mm-58mm) Desktop Thickness
Slide Lower Clamp (L) into the top 4 slots on Clamp Brace (K).
2” to 3.35” (50mm-85mm) Desk Thickness
Slide Lower Clamp (L) into the lower 4 slots on Clamp Brace (K).
Tighten rear screws with 4mm Allen Wrench (T-A).
Place Clamp Plate (G) on top of the clamp bolts on Lower Clamp (L).
Tighten rear screws with 4mm Allen Wrench (T-A).
Place Clamp Plate (G) on top of the clamp bolts on Lower Clamp (L). Install clamp assembly to desk and tighten clamp bolt using 6mm Allen Wrench (T-B). Snap Cover (J) onto the back of assembled base.

STEP 1b

Option B – Grommet
Attach Grommet Plate (H) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A). Remove protective film from Soft Pad (I) and apply to the underside of Grommet Plate (H). Position Base (A) over grommet hole in desk.
Remove a single clamp bolt from Lower Clamp (L) using 6mm Allen Wrench (T-B). Insert clamp bolt with Clamp Plate (G) through the underside of the desk and secure to Base (A) using 6mm Allen Wrench (T-B). No Grommet Hole?
If you do not have an existing hole for installation, drill a hole through your desktop in your desired mounting location using a 0.375” (10mm) drill bit.

STEP 2
Screw Lower Pole (C) into Base (A), and tighten set screws using 4mm Allen Wrench (T-A). Slide Pole Cable Clip (M) onto Lower Pole (C).

STEP 3
Slide one Arm (B) onto Lower Pole (C) and secure using 6mm Allen Wrench (T-B).

STEP 4
Thread Upper Pole (D) onto Lower Pole (C). Attach Pole Cable Clip (M) to Upper Pole (D).

Slide remaining Arm (B) onto Upper Pole (D) and tighten to the pole using 6mm Allen Wrench (T-B).Attach Cable Clips (F) to Arms (B). STEP 5
Securing VESA Plate to Monitors

Flat Back Monitors
Install VESA Plate (E) to your monitor using appropriate Screws (M-A thru M-D), M5 Washer (M-E) and a Phillips screwdriver. If needed, Spacers (M-F) are provided.

Recessed Mounting Pocked & Curved Screens
Install VESA Plate (E) to your monitor using appropriate Screws (M-A thru M-D), M5 Washer (M-E), Spacers (M-F), and a Phillips screwdriver.

Mounting Hardware Combinations

STEP 6
Partially install one Wing Nut (S-A) to the top screw on VESA Plate (E) on monitor and hang over the slot in the top of Arm (B).

Install the second Wing Nut (S-A) to the lower screw on VESA Plate (E).