levenhuk Ermenrich Seek MX10 Digital Luxmeter User Manual

: June 22, 2024
: levenhuk

Table of Contents

levenhuk Ermenrich Seek MX10 Digital Luxmeter
PRODUCT OVERVIEW
Getting started
Usage
Specifications
Care and maintenance
Battery safety instructions
Ermenrich Warranty
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

levenhuk Ermenrich Seek MX10 Digital Luxmeter

Levenhuk Inc. (USA): 928 E 124th Ave. Ste D, Tampa, FL 33612, USA, +1-813-468-3001, contact_us@levenhuk.com
Levenhuk Optics s.r.o. (Europe): V Chotejně 700/7, 102 00 Prague 102, Czech Republic, +420 737-004-919, sales-info@levenhuk.cz
Levenhuk®, Ermenrich® are registered trademarks of Levenhuk Optics s.r.o. (Europe).
© 2006–2024 Levenhuk, Inc. All rights reserved.
ermenrich.com
20240531

PRODUCT OVERVIEW

levenhuk-Ermenrich-Seek-MX10-Digital-Luxmeter-FIG-1

Light sensor cover MAX/MIN
(Max./min. values) button
UNIT (Units of measurement) button
Power button
Display
Battery compartment

Please carefully read the safety instructions and the user manual before using this product. Keep away from children. Use the device only as specified in the user manual.

The kit includes: digital luxmeter, user manual, and warranty.

Getting started

Open the battery compartment cover (6) and insert 2 AAA batteries, ensuring the correct polarity. Close the cover.
Hold the Power button (4) for 2 seconds to turn the device on or off.

Usage

Remove the sensor cover (1) and place the meter perpendicular to the light source. The illumination value will be displayed on the digital screen (5).
Press the UNIT button (3) to select the illumination unit: lx (LUX icon on the screen) or foot-candle (FC icon on the screen).
Press the MAX/MIN button (2) to enter extreme illumination values display mode. The MAX icon will light up on the screen and the maximum illumination values for the current measurement session will be displayed. Press the MAX/MIN button (2) again to display the minimum illumination values (MIN icon on the screen). Press and hold the MAX/MIN button (2) for more than 2 seconds to return to measurement.
When measurements are complete, close the sensor cover (1) to protect the filter and sensor.
The device turns off automatically after 10 minutes of inactivity. The function is active by default (the icon is displayed on the screen). To cancel, press and hold the UNIT button (3) while turning on the power. To restore the function, turn the device off and on again.

Specifications

Light intensity, units of measurement lx (lm/m2), fc (lm/ft2)
Light intensity, range 1000/10000/100000lx; 100/1000/10000fc
Accuracy ±(3.0% + 5lx)
Spectral range 320–730nm
Operating temperature range –10… +50°C (14… 122°F)
Storage temperature range –10… +50°C (14… 122°F)
Power supply 2pcs alkaline AAA batteries (1.5V)
Safety rating EN61326-1

The manufacturer reserves the right to make changes to the product range and specifications without prior notice.

Care and maintenance

Do not use the device if it is damaged or does not operate properly. Replace the battery as soon as the low battery indicator lights up. Do not use solvent to clean the device. Store the device in the place with appropriate temperature (see “Specifications”). Protect the device from sudden impact and excessive mechanical force. Never attempt to operate a damaged device or a device with damaged electrical parts! Only use accessories and spare parts for this device that comply with the technical specifications. If a part of the device or battery is swallowed, seek medical attention immediately.

Battery safety instructions

Always purchase the correct size and grade of battery most suitable for the intended use. Always replace the whole set of batteries at one time; taking care not to mix old and new ones, or batteries of different types. Clean the battery contacts and also those of the device prior to battery installation. Make sure the batteries are installed correctly with regard to polarity (+ and –). Remove batteries from equipment that is not to be used for an extended period of time. Remove used batteries promptly. Never short-circuit batteries as this may lead to high temperatures, leakage, or explosion. Never heat batteries in order to revive them. Do not disassemble batteries. Remember to switch off devices after use. Keep batteries out of the reach of children, to avoid risk of ingestion, suffocation, or poisoning. Utilize used batteries as prescribed by your country’s laws.

Ermenrich Warranty

Ermenrich products, except for their accessories, carry a 5-year warranty against defects in materials and workmanship. All Ermenrich accessories are warranted to be free of defects in materials and workmanship for six months from the purchase date. The warranty entitles you to the free repair or replacement of the Ermenrich product in any country where a Levenhuk office is located if all the warranty conditions are met.
For further details, please visit: levenhuk.com/warranty
If warranty problems arise, or if you need assistance in using your product, contact the local Levenhuk branch.

FAQ

Q: What is the warranty period for Ermenrich products?
A: Ermenrich products come with a 5-year warranty against defects in materials and workmanship, while accessories are warranted for six months.

Q: How should I handle batteries for the Ermenrich Seek MX10 Digital Luxmeter?
A: Follow the battery safety instructions provided in the user manual to ensure safe handling and usage of batteries.