belkin 599WIZ017B Boost and Charge Pro 3 In 1 Wireless Charger with MagSafe Instructions
- June 4, 2024
- belkin
Table of Contents
Boost and Charge Pro 3 In 1 Wireless Charger with MagSafe
Instructions
599WIZ017B Boost and Charge Pro 3 In 1 Wireless Charger with MagSafe
|
---|---
3-in-1 Wireless Charging Stand with MagSafe.
REGULATORY AND SUSTAINABILITY INFORMATION
Safety Instructions
WARNING: Failure to follow these instructions could result in fire, electric shock, injury, or damage to the user, or product. or other property.
- Connect the power supply of the wireless charger to a power outlet that is close by and Is easy to disconnect from the source.
- Use indoors and in a dry location only; Avoid charging near sources of heat and humidity.
- Keep the wireless charger and power supply away from any liquids or moisture.
- Unplug the wireless charger when not in use for long periods of time.
- Do not store your device in very hot or very cold locations. It is recommended to use your device at room temperature.
- Do not use if visible defects are observed on the wireless charger or power supply.
- Do not attempt to service, modify, or disassemble the wireless charger or power supply.
- Use of a power supply not recommended or sold by Belkin may result in an increased risk of fire, electric shock, injury, or damage to the user, product, or other property.
- The wireless charging power transmission rate is regulated by the wireless charging device receiving power which can be influenced by factors like, but not limited to, proprietary charging protocols, and ambient temperature. current battery percentage level and age of the device being charged.
CAUTION: If you experience problems with the wireless charger, please discontinue use, unplug the power supply from the AC socket, and contact Belkin for assistance. The marking information is located at the bottom of the apparatus.
FCC Statement
We, Belkin International, Inc. of 555 S Aviation Blvd., Suite 180, El Segundo, CA 90245-4852, Tel: +1 (310) 751 5100, declare under our sole responsibility that this product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, Including Interference that may cause undesired operation.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates. uses, and can radiate
radio frequency energy, and if not installed and used In accordance with the
instructions. may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user Is encouraged to try and correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
Innovation, Science, and Economic Development Canada Statement (ISED):
This device contains license-exempt transmitter(s)/receiver(s) t that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following conditions
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
Innovation, Science and Economic Development Canada Statement: This digital
apparatus complies with CAN ICES-003(B) / NMB-003(B).
Belkin International, Inc. 555 S Aviation Blvd Suite 180
El Segundo, CA 90245-4852
Belkin Asia Pacific Ltd. Hong Kong
Belkin Tech Support: www.belkin.com/support
Made in Vietnam.
belkin.com
8850tt01611 Rev.A00
Documents / Resources
|
belkin 599WIZ017B Boost and Charge Pro 3 In 1 Wireless Charger with
MagSafe
[pdf] Instructions
599WIZ017B, Boost and Charge Pro 3 In 1 Wireless Charger with MagSafe,
599WIZ017B Boost and Charge Pro 3 In 1 Wireless Charger, 599WIZ017B Boost and
Charge Pro 3 In 1 Wireless Charger with MagSafe
---|---
References
- Mobile & Computer Accessory Products | Belkin US
- Live Chat, User Guides, FAQs & More | Belkin Support US