GOLDEN LIGHTING 6938-2W BLK-BR Avon 2 Light 17 Inch Tall Wall Sconce Instruction Manual
- June 22, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 6938-2W BLK-BR Avon 2 Light 17 Inch Tall Wall Sconce
Thank You for Choosing Us for Your Lighting Needs!
Dimensions
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice.
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
Assembly Instructions
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. The mounting strap contains several pairs of threaded
holes. Find the pair of holes that matches the spacing of the holes on the
junction box and your fixture’s backplate. Be sure that the screw holes are
vertical. Test backplate (C) to mounting strap (B) to ensure that it will hang
straight. Place the backplate (C) aside. Pull the house wires through the
center of mounting strap (B). 2. Secure mounting strap (B) to the junction box
with mounting screws (D) and a screwdriver. Tighten the screws securely
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
3. Have an assistant support the fixture’s weight while completing the
wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw on the mounting bracket/mounting strap and
wrap the fixture’s ground wire around the ground screw. Use a screwdriver to
tighten the top of ground screw onto the wires and into the mounting bracket/
mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
4. Place backplate (C) over mounting strap (B) and align side holes found on
backplate (C) with the side holes found on the tabs of mounting strap (B).
Once aligned, secure backplate (C) to mounting strap (B) using both mounting
screws (A) on the tabs of mounting strap (B). Thread until secure. 5. Install
light bulbs (not included) into sockets (G) in accordance with the fixture’s
specifications.
Do not exceed the maximum. Your installation is now complete. Turn on the
power and test the fixture. (NOTE: If the shade needs to be removed for any
reason. Use a long screwdriver through the shade to turn the screw to remove
the shade.)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>