GOLDEN LIGHTING 1945-1W Axel 14 Inch Tall Wall Sconce Instruction Manual
- June 21, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1945-1W Axel 14 Inch Tall Wall Sconce Instruction Manual
Thank You for Choosing Us for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice.
Assembly Instructions
How to Identify the Fixture’s Wires
Hot : Smooth, Black, or Transparent with Black Inner Thread
Neutral : Ribbed, White or Transparent with White Inner Thread
Ground : Copper, Bare Metal, Green, or Transparent Inner Thread
**Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
• All installation work should be done by accredited professional.
• Shut off power supply at fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Mounting strap (B) contains several pairs of threaded
holes. Find the pair of holes that matches the spacing of the holes on the
junction box and your fixture’s backplate (F). Two sets of mounting screws (A
& D) should be attached to mounting strap (B). You may need to tighten the
nuts (C) that hold these this screws in place. Place mounting strap (B) over
the junction box so that mounting screws (A) are horizontal, and in alignment
with the holes located on the backplate (F). Secure mounting strap (B) to the
junction box using mounting screws (D) and a screwdriver. Tighten the screws
securely. Pull house wires through the center of the mounting strap.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
2. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
(PLEASE NOTE: This fixture can be installed with or without shade.) TO INSTALL
WITHOUT THE SHADE REFER TO DIAGRAM (1): 3. Place backplate (F) onto over
mounting strap (B) until mounting screws (A) protrude through holes in the
front of the backplate (F). Thread deco nuts (G) onto mounting screws (A).
Twist until the backplate (F) of the fixture is snug against the wall. 4.
Install a light bulb (not included) into socket in accordance with the
fixture’s specifications. Do not exceed the maximum recommended wattage. Your
installation is now complete. Turn on the power and test the fixture. TO
INSTALL WITH THE SHADE REFER TO DIAGRAM (2): 3. Place backplate (F) onto over
mounting strap (B) until mounting screws (A) protrude through holes in the
front of the backplate (F). Thread deco nuts (G) onto mounting screws (A).
Twist until the backplate (F) of the fixture is snug against the wall.4.
Carefully attach glass shade (K) and socket cover (L) to socket (I) and secure
with socket ring (J). 5. Install a light bulb (not included) into socket in
accordance with the fixture’s specifications. Do not exceed the maximum
recommended wattage. Your installation is now complete. Turn on the power and
test the fixture.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>