Golden Lighting 6085-SF Wide Semi Flush Square Ceiling Fixture Installation Guide
- June 19, 2024
- GOLDEN LIGHTING
Table of Contents
6085-SF Wide Semi Flush Square Ceiling Fixture
Thank You for Choosing Us for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice.
Assembly Instructions
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement
parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. From the parts bag remove the mounting strap (B) assembly.
Mounting strap (B) contains several threaded holes. Two sets of mounting
screws (A & D) should be attached to mounting strap (B). You may need to
tighten nuts (C) that hold mounting screws (A) in place. If the screws are not
attached, please hold canopy (F) up to mounting strap (B). Line up the holes
in canopy (F) with the holes in mounting strap (B) and insert mounting screws
(A) into mounting strap (B) so that mounting screws (A) protrude through the
holes in canopy (F). Mounting screws (A) are long, so please test the canopy
against the mounting strap to see how far you should insert the screws.
Tighten nuts (C) onto mounting screws (A) to hold the screws in place. 2. Pull
the house wires through the center of mounting strap (B). Place mounting strap
(B) over the junction box so that mounting screws (A) are in alignment with
the hole locations on the fixture’s canopy (F). Secure mounting strap (B) to
the junction box with mounting screws (D) and a screwdriver. Tighten the
screws securely.
ASSEMBLING THE FIXTURE
3. Thread the fixture’s wires from post (I) through the rod (H), swivel and
canopy (F). Pull the wires until taut. Thread rod (H) onto the post (I) and
secure using provided tool to tighten the small screw on swivel.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
5. Push canopy (F) up to the ceiling over mounting screws (A) so that they
protrude through the holes in canopy (F). Tightly thread deco nuts (G) onto
mounting screws (A) until the canopy is snug against the ceiling. Install
light bulbs (not provided) into sockets (J) accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage. Your
installation is complete. Turn on the power and test the fixture.
Get help, quick tips, and explore curated content
SCAN ME
http://lightinginstructions.com/
Documents / Resources
|
Golden Lighting 6085-SF Wide Semi Flush Square Ceiling
Fixture
[pdf] Installation Guide
6085-SF Wide Semi Flush Square Ceiling Fixture, 6085-SF, Wide Semi Flush
Square Ceiling Fixture, Square Ceiling Fixture, Ceiling Fixture, Fixture
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>