GOLDEN LIGHTING 6933-M Florence 14 Wide Pendant Instruction Manual
- June 11, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 6933-M Florence 14 Wide Pendant
Specifications
- Model : 6933-M
- Model Variants : 6933-M BLK-NR
- Fixture Type : Pendant Light
- Maximum Wattage : Refer to fixture’s specifications
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island:
Center a linear pendant over the island. If hanging pendants, use one
pendant for every 24 inches of the island. Fixtures should hang at least 30
inches above the countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30 inches above the table. Use a fixture that
is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance
for any opening doors.
Installation Steps
- Prepare for installation.
- Assemble the fixture components according to the provided instructions.
- Connect the fixture wires following the wiring diagram.
- Complete the installation by securing the canopy in place and installing a suitable light bulb.
Tips for Best Lighting
To achieve optimal lighting in your space, consider layering your lighting
with fixtures like sconces, flush mounts, and pendants. Use dimmers to control
light output as needed for different tasks and ambiance.
For Customer Service
If you require assistance or replacement parts, please contact the place of
purchase for customer service support.
FAQ
-
How do I determine the appropriate height for pendant lights above a kitchen island?
- For pendant lights above a kitchen island, center a linear pendant over the island or use one pendant for every 24 inches of island width. Ensure the fixtures hang at least 30 inches above the countertop.
-
Can I install these fixtures in open areas with high ceilings?
- Yes, you can install pendants and chandeliers in open areas with high ceilings. Ensure that the bottom of the fixture hangs at least 7.5 feet from the floor to provide adequate clearance.
-
What type of light bulbs should I use with the fixture?
- Refer to the fixture’s specifications for the recommended maximum wattage and suitable light bulb types. Install a light bulb that complies with these specifications to ensure safe and optimal performance.
Thank You for Choosing Us for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice.
How to Identify the Fixture’s Wires
- Hot : Smooth, Black, or Transparent with Black Inner Thread
- Neutral : Ribbed, White or Transparent with White Inner Thread
- Ground : Copper, Bare Metal, Green, or Transparent Inner Thread
Assembly Instructions
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power
at the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. From the parts bag remove the mounting strap assembly. One
end of nipple (F) should be attached to mounting strap (A) with washer (C) and
hex nut (D) in place. The other end should have canopy loop (H) and canopy
loop collar (I) attached. Attach mounting strap (A) to the junction box using
mounting screws (B) and a screwdriver. Tighten securely. 2. Unscrew canopy
loop collar (I) from canopy loop (H) and slide down. Pass canopy (G) over the
mounted canopy loop (H) to test the fixture height. Approximately half of the
exterior threads of the canopy loop (H) should be exposed, and the canopy loop
collar (I) should fit snugly onto the canopy loop (H). If need be, remove
canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the
desired height is reached.
ASSEMBLING THE FIXTURE
Feed the fixture wires from post (P) into nipple (O) through deco cover (N),
nut (M), and top loop (L). Pull the wires until taut. Thread the nipple (O)
onto post (P). Attach the deco cover (N) onto the nipple (O). Secure deco
cover needed for proper hanging height. If necessary, use a pair of pliers to
open and remove any excess chain. Attach one chain connector (K) to each end
of the chain (J). Attach one end of the chain/chain connector to attach to the
top loop (L). Use the remaining end of the chain/chain connector to attach to
canopy loop (H). Close the chain connectors (K) secure. Feed the fixture wires
from top loop (L) up through the chain (every three links or so), canopy loop
(H), canopy loop collar (I), and canopy (G). Pull the wires until taut. Slide
canopy loop collar (I) and canopy (G) down onto the chain/wires.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate the ground screw (E) on the mounting bracket/mounting
strap and wrap the fixture’s ground wire around the ground screw. Use a
screwdriver to tighten the top of the ground screw (E) onto the wires and into
the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath
the canopy. Tightly thread canopy loop collar (I) onto canopy loop (H) to
secure canopy (G) in place. Install a light bulb (not included) into socket
(Q) found within shade (R) in accordance with the fixture’s specifications. Do
not exceed maximum recommended wattage. Your installation is now complete.
Turn on the power and test the fixture.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>