GOLDEN LIGHTING 7011-5 Winslett 5 Light 24 Inch Gold Chandelier Ceiling Light Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 7011-5 Winslett 5 Light 24 Inch Gold Chandelier Ceiling
Light
Thank You for Choosing Us for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment. Get function and style! Browse our site for coordinating lights
and expert lighting advice.
Assembly Instructions
How to Identify the Fixture’s Wires
- Hot : Smooth, Black, or Transparent with Black Inner Thread
- Neutral : Ribbed, White or Transparent with White Inner Thread
- Ground : Copper, Bare Metal, Green, or Transparent Inner Thread
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. Mounting strap (A) should have one end of nipple (F) attached with washer (C) and hex nut (D) in place. The other end should have canopy loop (H) attached. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop (H). Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached. 2. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely.
ASSEMBLING THE FIXTURE
Feed the fixture wires from post (P) through center rod (N) and top loop (L). Connect nipple (O) of center rod (N) onto post (P) of the fixture’s body. Pull the wires until taut. Screw top loop (L) into post (M) at the top of rod (N). Measure to determine the correct length of chain needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach one of the chain connectors (K) to each end of the chain (J). Use one of the chain/chain connectors to attach to the top loop (L) and connect the remaining end of chain/chain connector to canopy loop (H). Close the chain connectors to secure. Feed the fixture’s wires through the chain (every three links or so), canopy loop (H), canopy loop collar (I), canopy (G), and nipple (F). Pull the wires until taut. Keep at least 8 to 10 inches of wire more than the desired length and trim the excess wires.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate the ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of the ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (G) up to the mounting strap. Thread canopy loop (H) onto the exposed threads of nipple (F). Then, tightly thread canopy loop collar (I) onto canopy loop (H). 6. Slide glass shades (S) over sockets (Q) and secure in place with socket covers (R). Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
Get help, quick tips, and explore curated content: Lightinginstructions.com
Documents / Resources
|
GOLDEN LIGHTING 7011-5 Winslett 5 Light 24 Inch Gold Chandelier Ceiling
Light
[pdf] Instruction Manual
7011-5 Winslett 5 Light 24 Inch Gold Chandelier Ceiling Light, Winslett 5
Light 24 Inch Gold Chandelier Ceiling Light, Light 24 Inch Gold Chandelier
Ceiling Light, Gold Chandelier Ceiling Light, Chandelier Ceiling Light,
Ceiling Light, Light
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>