BELLEVUE Masha 10 Tall Outdoor Wall Sconce Instruction Manual
- June 9, 2024
- BELLEVUE
Table of Contents
- BELLEVUE Masha 10 Tall Outdoor Wall Sconce
- Tools Required (not included):
- Bulb Recommended:
- Preparation:
- Warnings And Cautions
- Package Contents
- STEP 1:
- STEP 2:
- STEP 3:
- STEP 4:
- STEP 5:
- Glass replacement:
- CARE AND MAINTENANCE
- TROUBLESHOOTING
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BELLEVUE Masha 10 Tall Outdoor Wall Sconce
INSTRUCTION MANUAL
Tools Required (not included):
Flathead screwdriver, Phillips screwdriver,, Electrical tape, Safety goggles, silicon sealant.
Bulb Recommended:
(1) 60W Type-A medium base bulb, Alternate (1) LED bulb. Estimated Assembly Time: 20 – 30 minutes
Preparation:
- Identify and inspect all parts before beginning installation
- Check package contents list and diagrams below to be sure all parts are included .
- If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.
Warnings And Cautions
- Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. .
- These instructions are provided for your safety. It is very important you read them completely before installing fixture.
- We strongly recommend that a licensed, professional electrician perform the installation. . Disconnect fixture from power source before replacing bulbs .
- Make sure bulbs are given sufficient time to cool before removal.
- Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
| PART | DESCRIPTION | QUANTITY | Stock Part# |
|---|---|---|---|
| A | Crossbar | ||
| (Pre-assembled to fix ture body) | 1 pc | 913058KIT | |
| B | Green Ground Screw | ||
| (Pre-assembled to Crossbar) | 1 pc | ||
| C | Wire Connector | 3 pcs | |
| D | Outlet Box Screw | 2 pcs | |
| E | Mounting Screw | ||
| (Pre-assembled to fixture body) | 2 pcs | ||
| F | Fixture Body | 1 pc | NIA |
| G | Glass | ||
| (Pre-assembled to fix ture body) | 4 pcs | G13061PA |
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2″
STEP 1:
a. Secure the crossbar to the outlet box (not included) with outlet box
screws.
b. Tighten until snug.
Note: Place a cloth or towel on the ground under the work area to prevent
loss of mounting hardware if dropped.
Note: The tabs on the crossbar should protrude outward.
STEP 2:
- Use Wire Connectors (supplied) to connect the wires.
a) Ground Wire:
1. Wrap supply ground wire around green ground screw on mounting bracket, no
less than 2 in. from the end of the wire. Tighten ground screw.
2. Connect fixture ground wire to supply ground wire with wire connector.
b) Supply Wire:
1. Connect the supply white wire to the white fixture supply wire with wire
connector.
2. Connect the supply black (or red) wire to the black fixture supply wire
with wire connector.
3. Wrap each connection with approved electrical tape and carefully stuff all
of the connected wires into the outlet box.
STEP 3:
a. Line up holes on the backplate and mounting holes on the folded edge of the
crossbar.
b. Secure by threading mounting screws into the mounting holes on the
crossbar.
c. Thread screw into one side first. Do not fully tighten.
d. Thread screw into opposite side and tighten with screwdriver.
e. Tighten screw from step c with screwdriver.
STEP 4:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
STEP 5:
NOTE : To ensure proper moisture drainage, do not seal bottom of fixture backplate.
a. Make sure the surface of the exterior wall and fixture backplate are free
of dirt.
b. Using silicone sealer (not included) start on one side of fixture backplate
and follow contour where the fixture backplate meets the exterior wall
surface.
c. Proceed to seal around backplate.
d. Place silicone sealant over the head of each mounting screw and mounting
holes on the backplate.
Your installation is now complete! Restore electricity and save this sheet for future reference.
Glass replacement:
Note: Place a cloth or towel on the ground under the work area to prevent loss of mounting hardware if dropped.
a. Remove lock screw, cage, glass from the fixture body.
b. Remove the glass and add the replacement into the same position.
c. Attach the cage with the glass back onto the fixture body and secure with
lock screws.
CARE AND MAINTENANCE
Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixture as they may damage the finish.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Bulbs will not light. | 1. Bulb is burned out. |
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.| I. Replace light bulb.
2. Make sure power supply is on.
3. Check wiring.
4. Test or replace the switch.
Fuse blows or the circuit breaker trips when light is turned| Crossed wires or
power wire is grounding out.| Check wire connection.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>