BELLEVUE MVLWS66042ORB Ethyl 3 Light 13 Tall Outdoor Wall Sconce Instruction Manual

BELLEVUE MVLWS66042ORB Ethyl 3 Light 13 Tall Outdoor Wall Sconce

Product information

• Tools Required: Flathead screwdriver, Phillips screwdriver, silicon sealant, wire strippers, electrical tape, safety glasses.
• Bulb Recommended: (3) Candelabra Base 60W Maximum, Alternate (3) LED bulb.
• Estimated Assembly Time: 20 – 30 minutes

Preparation

• Identify and inspect all parts before beginning installation
• Check the package contents list and diagrams below to be sure all parts are included.
• If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.
• Contact Quoizel Customer Service for replacement parts.

Warnings And Cautions

Turn off electricity at the circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation. Disconnect the fixture from the power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

PART| | DESCRIPTION

Crossbar Assembly

(Pre-assembled to fixture body)

Green Ground Screw

(Pre-assembled to Crossbar)

Wire Connector Outlet Box Screw Fixture Body

Glass

(Pre-assembled to fixture body)

| QUANTITY

1 pc

1 pc

3 pcs

2 pcs

1 pc

1 pc

| Stock Part#
---|---|---|---|---
A|
B| | 912575KIT
C D

E

| |
N/A
F| | G12577SH

Dimension

Installation Instruction

STEP 1:

• a. Secure the crossbar to the outlet box (not included) with outlet box screws.
• b. Tighten until snug.
  Note: Place a cloth or towel on the ground under the work area to prevent loss of mounting hardware if dropped.
  Note:The preassembled mounting screws on the crossbar should protrude outward.

STEP 2:

• a. Remove mounting balls from the crossbar assembly.
• b. Fit the backplate to the crossbar assembly and secure it with mounting balls.

Note: The backplate should be snug against the wall and the mounting balls.

• If not, adjust the length of the mounting screw on the crossbar assembly by unscrewing the preassembled hex nut.
• Then screw the mounting screws in or out of the crossbar until the correct length is achieved.
• Unce the backplate is secure, remove the mounting balls and backplate and proceed to step 3.

STEP 3:

• Use Wire Connectors (supplied) to connect the wires.

a) Ground Wire:

1. Wrap supply ground wire around green ground screw on mounting bracket, no less than 2 in. from the end of the wire. Tighten ground screw.
2. Connect fixture ground wire to supply ground wire with wire connector.

b) Supply Wire:

1. Connect the supply white wire to the white fixture supply wire with wire connector.
2. Connect the supply black (or red) wire to the black fixture supply wire with wire connector.
3. Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the outlet box.

STEP 4:

• a. Re-attach the backplate of the fixture body to the crossbar assembly.
• b. Secure with the previously removed mounting balls.

STEP 5:

• a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.

STEP 6:

• a. Make sure the surface of the exterior wall and fixture backplate are free of dirt.
• b. Using silicone sealer (not included) start on one side of fixture backplate and follow contour where the fixture backplate meets the exterior wall surface.
• c. Proceed to seal around the backplate.

NOTE: To ensure proper moisture drainage, do not seal the bottom of fixture backplate. Your installation is now complete! Restore electricity and save this sheet for future reference.

Glass replacement:

Note: Place a cloth or towel on the ground under the work area to prevent loss of mounting hardware if dropped.

• a. Remove the lock screw, cage, and glass from the fixture body.
• b. Remove the glass and add the replacement into the same position.
• c. Attach the cage with the glass back onto the fixture body and secure with lock screws.

CARE AND MAINTENANCE

Wipe clean using a soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixtures as they may damage the finish.

TROUBLESHOOTING

PROBLEM| POSSIBLE| CAUSE| | CORRECTIVE| ACTION|
---|---|---|---|---|---|---
Bulbs will not light.| 1.  Bulb is burned out.

2.  Power is off.

3.  Faulty wire connection.

4.  Faulty switch.

| 1.  Replace light bulb.

2.  Make sure the power supply is on.

3.  Check wiring.

4.  Test or replace the switch.

Fuse blows or the

circuit breaker trips when light is turned

| ****

Crossed wires or power wire is grounded out.

| ****

Check the wire connection.

on.| |

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>