BELLEVUE MVLCH95142WBLK Drea 5 Light 36 Wide Abstract Linear Chandelier Instruction Manual

BELLEVUE MVLCH95142WBLK Drea 5 Light 36 Wide Abstract Linear Chandelier

Important Information

Tools Required (not included)

• Flathead screwdriver
• Phillips screwdriver
• Wire cutters
• Electrical tape
• Safety goggles
• Ladder

Helpful Tools (not included)

• Wire strippers

Bulb Recommended

(5) 60W Type-S medium base vintage-style bulb (not included), Alternate (5) LED bulb.

Estimated Assembly Time

• 20 – 30 minutes

Preparation:

• Identify and inspect all parts before beginning installation
• Check package contents list and diagrams below to be sure all parts are included .
• If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.

Warnings And Cautions

• Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. . These instructions are provided for your safety. It is very important you read them completely before installing fixture. We strongly recommend that a licensed, professional electrician perform the installation. . Disconnect fixture from power source before replacing bulbs .
• Make sure bulbs are given sufficient time to cool before removal.
• Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

914162 KIT

AA| Wire Connector| 3 pcs
BB| Outlet Box Screw| 2 pcs
cc| Quick Link| 4 pcs
B| Fixture Chain| 2 pcs| M382CHS42
C| Ceiling Canopy| 1 pc|

N/A

D| Fixture Loop| 2 pcs
E| Washer| 2 pcs
F| Fixture| 1 pc

Installation Instructions

STEP 1:

• a. Secure the crossbar to the outlet box (not included) with outlet box screws.
• b. Tighten until snug.
  Note: The preassembled mounting nipple on the crossbar should protrude outward.
  

STEP 2:

• a. Remove lock ball and hex nut from crossbar assembly.

• b. Fit ceiling canopy over the nipple on crossbar assembly and secure with lock ball.
  Note: The ceiling canopy should be snug against the ceiling and the lock ball.

• If not, adjust the length of the nipple on the crossbar assembly by unscrewing the preassemble hex nut.

• Then, screw the nipple in or out of the crossbar until the desired length is achieved.

• Once the ceiling canopy is secure, remove the lock ball and ceiling canopy and proceed to Step 3.
  

STEP 3:

• a. Thread the fixture loop, the washer and the fixture together as shown.
• b. Hand tighten until snug.
• c. Connect end of each Fixture Chain to the loops preassembled to Ceiling Canopy with Quick Links.
• d. Adjust each socket cord to desired length. Refer to Step 4.
• e. Choose desired hanging height for the light fixture. Suggested mounting height over a table or island is 30 inches from the table/island top to the bottom of the lowest hanging bulb.
• f. Remove excess fixture chain.
  Note: You may need to use pliers (not included) to open the links of Fixture Chain. If so, put a cloth over the Fixture Chain to protect the finish from the pliers.
  

STEP 4:

NOTE : You can wrap each cord per your preference as shown.

• a. Wrap sockets in alternating directions.
• b. To create a staggered look, loop alternating sockets as shown in diagram below.
• c. Install bulbs temporarily for height adjustments.
  

STEP 5:

• a. The lanyard is provided as a means to support the fixture from the junction box while connecting the electrical wires. This enables the fixture to hang from the junction box and your hands are free to make the wire connections.
• b. Turn the button stop so it may be inserted into the crossbar slot. Make sure the button stop is completely inside the crossbar.
• c. Slowly release the fixture to make sure it is supported by the button stop.
• d. Proceed to Step 6. Once wiring is complete, the lanyard will push into the junction box when the Ceiling Canopy is Attached to the ceiling.
  

STEP 6:

• a. Confirm that the mounting height is acceptable. Refer to STEP 3 if changes are required.

• b. Remove bulbs to prevent breakage during final installation steps.
  Note: To make the next step easier, cut the supply wire and A u – Fixture Chain ground wire 24 inches longer than the distance from the Supply Wire fixture loop to the ceiling. Important: Please pay attention r, and Ground Wire to the polarity (wires labels L & N) when cutting wires. Wire identification will be needed in STEP 7.

• c. Pull the Supply Wires and Ground Wire up through the  Fixture Chain alternating links.

• d. Push the ends of the supply wires and ground wire up through the canopy loop and into the outlet box. The remaining slack wire will be pushed into the box in STEP 7.
  

STEP 7:

• Use Wire Connectors (supplied) to connect the wires.

  • a) Ground Wire:
    
  1. Wrap supply ground wire around green ground screw on mounting bracket, no less than 2 in. from the end of the wire. Tighten ground screw.
  2. Connect fixture ground wire to supply ground wire with wire connector.
  • b) Supply Wire:
    
  1. Connect the supply white wire to the fixture supply wire (ribbed sided) from fixture identified with the label “N”.
  2. Connect the supply black (or red) wire to the fixture supply wire (smooth side) from fixture identified with the label “L”.
  3. Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the outlet box.
     

STEP 8 :

• a. Re-attach the ceiling canopy to the crossbar assembly.
• b. Secure with the previously removed hex nut.
• c. Then, attached the lock ball over the ceiling canopy.
  

STEP 9 :

a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.

Your installation is now complete! Restore electricity and save this sheet for future reference.

CARE AND MAINTENANCE

Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixture as they may damage the finish.

TROUBLESHOOTING

1. Bulb is burned out.
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.

|

1. Replace light bulb.
2. Make sure power supply is on.
3. Check wiring.
4. Test or replace the switch.

Fuse blows or the circuit breaker trips when light is turned on.| Crossed wires or power wire is grounding out.| Check wire connection.

Printed in China

Documents / Resources

| BELLEVUE MVLCH95142WBLK Drea 5 Light 36 Wide Abstract Linear Chandelier [pdf] Instruction Manual
MVLCH95142WBLK Drea 5 Light 36 Wide Abstract Linear Chandelier, MVLCH95142WBLK, Drea 5 Light 36 Wide Abstract Linear Chandelier, Wide Abstract Linear Chandelier, Abstract Linear Chandelier, Linear Chandelier, Chandelier
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>