Bellevue MVLCH49586MBK Almeda 5 Light 24 Wide Ring Chandelier Instruction Manual

Bellevue MVLCH49586MBK Almeda 5 Light 24 Wide Ring Chandelier

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, electrical tape, safety glasses, and ladder.
Helpful Tools (not included): Wire strippers
Bulb Recommended: (5) 60W Type-S medium base vintage-style bulbs, Alternate (5) LED bulbs.
Estimated Assembly Time: 20 – 30 minutes

Preparation

• Identify and inspect all parts before beginning installation
• Check the package contents list and diagrams below to be sure all parts are included.
• If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.

Warnings And Cautions

• Turn off electricity at the circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
• These instructions are provided for your safety. You must read them completely before installing the fixture.
• We strongly recommend that a licensed, professional electrician perform the installation.
• Disconnect the fixture from the power source before replacing the bulbs.
• Make sure bulbs are given sufficient time to cool before removal.
• Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

STEP 1

• Once the installation method is determined, attach the end of the side chain to the hooks.
• Ensure the chain has no twists or kinks.

STEP 2

• Secure the Crossbar Assembly to the outlet box (not included) with Outlet Box Screws.
• Tighten until snug.
  Note: The preassembled mounting nipple on the crossbar should protrude outward.

STEP 3

• Remove the pre-assembled canopy lock ring from the crossbar assembly.
• Temporarily attach the ceiling canopy to the pre-assembled nipple on the crossbar assembly.
• Secure with canopy lock ring.
  Note
  If the ceiling canopy is not snug against the ceiling, remove it from the crossbar assembly and adjust the length of the pre-assembled nipple by unscrewing the pre-assembled hex nut. Screw the nipple in or out of the crossbar until the correct length is achieved. Then, re-attach the ceiling canopy.

STEP 4

• Choose the desired hanging length for the light fixture. The suggested mounting height over a table or island is 30 inches from the table/island top to the bottom of the fixture.
• Adjust the Fixture Chain to the desired length, removing links if needed.
• Connect one end of the Fixture Chain to the canopy chain loop preassembled to the Crossbar Assembly with one Quick Link.
• Connect the other end of the Fixture Chain to the fixture loop with the remaining Quick Link.
  Note: You may need to use pliers (not included) to open the links of the Fixture Chain. If so, put a cloth over the Fixture Chain to protect the finish from the pliers.

Suggested chain length to hang fixture 30 inches above tabletop:

• 8-ft. Ceiling: 10 inches of chain + 2 quick links
• 9-ft. ceiling: 22 inches of chain + 2 quick links
• 10-ft. ceiling: 35 inches of chain + 2 quick links
• 11-ft. ceiling: 47 inches of chain + 2 quick links
• 12-ft. ceiling: 59 inches of chain + 2 quick links

STEP 5

• Confirm that the mounting height is acceptable. Refer to STEP 4 if changes are required.
  Note: To make the next step easier, cut the supply wire and ground wire 24 inches longer than the distance from the fixture loop to the ceiling.
  Important: Please pay attention to the polarity (wires labels L & N) when cutting wires. Wire identification will be needed in STEP 7.

• Pull the Supply Wires and Ground Wire up through the Fixture Chain alternating links.

• Push the ends of the supply wires and ground wire up through the canopy chain loop and into the outlet box. The remaining slack wire will be pushed into the box in STEP 6.

STEP 6

• Unthread the canopy lock ring.
• Slide the canopy lock ring and ceiling canopy down the quick link.
• Push all slack fixture wire through the canopy chain loop and into the outlet box.
• Trim excess fixture wire leaving a minimum of 6 inches hanging out of the outlet box.
• Separate the smooth side and ribbed side of the supply wire to about 3 inches from the end.
• Using wire strippers, strip each wire ½ inch from the end.

STEP 7
Use Wire Connectors (supplied) to connect the wires.

Ground Wire

1. Wrap supply ground wire around the green ground screw on the mounting bracket, no less than 2 in. from the end of the wire. Tighten the ground screw.
2. Connect fixture green ground wire to supply ground wire with a wire connector.

Supply Wire

1. Connect the house white wire to the fixture supply wire (ribbed-sided) from the fixture identified with the label “N”.
2. Connect the house black (or red) wire to the fixture supply wire (smooth side) from the fixture identified with the label “L”
3. Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the outlet box.

STEP 8

• Attach the ceiling canopy back over the canopy chain loop.
• Secure with canopy lock ring.

STEP 9

• Remove the socket collar from the socket on the fixture assembly.
• Then place the shade over the socket on the fixture assembly as shown.
• Secure by threading the socket collar onto the socket.
• Hand-tighten until snug.

STEP 10
Install correct bulbs referring to fixture markings and/or labels for maximum wattage. Your installation is completed now. Restore electricity. Retain this sheet for future reference.

CARE AND MAINTENANCE

Wipe clean using a soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixtures as they may damage the finish.

TROUBLESHOOTING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>