BELLEVUE MVLP23797WH Sosius 15 Wide Pendant Instruction Manual

BELLEVUE MVLP23797WH Sosius 15 Wide Pendant

Tools Required (not included):
Flathead screwdriver, Phillips screwdriver, Pliers, Wire cutters, Electrical tape, Safety goggles, Ladder.

Helpful tools (not included): Wire Stripper
Bulb Recommended: (1) 1 00W Type-A medium base bulb, Alternate (1) LED bulb. Estimated Assembly Time: 20 – 30 minutes

Preparation:

• Identify and inspect all parts before beginning installation
• Check the package contents list and diagrams below to be sure all parts are included. If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.

Warnings And Cautions

• Turn off electricity at the circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
• These instructions are provided for your safety. You must read them completely before installing fixture. We strongly recommend that a licensed, professional electrician perform the installation.
• Disconnect the fixture from the power source before replacing bulbs.
  • Make sure bulbs are given sufficient time to cool before removal.
  • Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

PART| DESCRIPTION

Crossbar Assembly

(Pre-assembled to Fixture Body)

| QUANTITY| Stock Part#
---|---|---|---
A| 1 pc|
| | 914 164 KIT
AA| Wire Connector| 3 pcs
BB| Outlet Box Screw| 2 pcs|
cc| Mounting Screw

(Pre-assembled to Crossbar)

| 2 pcs|
B| Fixture| 1 pc| N/A
C

D

| Ring| 1 pc|
Shade| 1 pc| M14172RGEK
E| Socket Collar(Pre-assembled to Fixture Body)| 1 pc| N/A

ASSEMBLING

• STEP 1:

  • Remove the crossbar from the ceiling canopy on the fixture body.
  • Secure the crossbar to the outlet box (not included) with outlet box screws.
  • Tighten until snug.
    Note : The tab on the crossbar should protrude outward.

• STEP 2:

  • A. Loosen the set screw on the coupling of the underside of the ceiling canopy. Adjust the cord in or out of the ceiling canopy according to your hanging height.

  • B. Tighten the set screw on the coupling once your hanging cord- t
    Recommended length, from the top of the canopy to the bottom of the socket, when mounting above a 30-inch high table: 8-foot ceiling 30 inches

  • 9-foot ceiling 42 inches

  • 10-foot ceiling 54 inches

  • 11 foot ceiling 66 inches

  • 12-foot ceiling 78 inches
    Note: The fixture wire should be slightly longer than the cable. Do not cut the fixture wire. This will be done in step 3.

• STEP 3:

  • Confirm the desired hanging height. Refer to step 2 if adjustments are needed.
  • Using wire cutters, cut the fixture wire leaving approximately 10 inches of wire extending from the Canopy. On the fixture wire, remove 4 inches of the outer sleeve.
  • Using wire strippers, strip each wire½ inch from the end.

• STEP 4:

  • The lanyard is provided as a means to support the fixture from the junction box while connecting the electrical wires. This enables the fixture to hang from the junction box and your hands are free to make the wire connections.
  • Turn the button stop so it may be inserted into the crossbar slot. Make sure the button stop is completely inside the crossbar.
  • Slowly release the fixture to make sure it is supported by the button stop.
  • Proceed to Step 5. Once the wiring is complete, the lanyard will push into the junction box when the Ceiling Canopy is Attached to the ceiling.

• STEP 5:
  Use Wire Connectors (supplied) to connect the wires.

  • Ground Wire:

  • 1. Wrap supply ground wire around the green ground screw on the mounting bracket, no less than 2 in. from the end of the wire. Tighten the ground screw.
    2. Connect fixture green ground wire to supply ground wire with a wire connector.

  • Supply Wire:

  • Connect the supply white wire to the white fixture supply wire with a wire connector.

  • Connect the supply black (or red) wire to the black fixture supply wire with a wire connector.

  • Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the outlet box.

• STEP 6:

  • Line up the holes on the canopy of the fixture body and the mounting holes on the crossbar.
  • Secure with the mounting screws. Tighten until snug.

• STEP 7:

  • Remove the socket collar from the socket on the fixture.
  • Position ring so that the curled lip is facing up. Place the ring on the shade.
  • Place the shade over the socket on the fixture as shown.
  • Hand-tighten until snug.

• STEP 8:

  • Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
    Your installation is now complete! Restore electricity and save this sheet for future reference.

CARE AND MAINTENANCE

• Wipe clean using a soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixtures as they may damage the finish.

TROUBLESHOOTING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>