BELLEVUE MVLCH61357MTBG Gold Zuri 4 Light 36 Inch Wide Linear Chandelier Installation Guide

BELLEVUE MVLCH61357MTBG Gold Zuri 4 Light 36 Inch Wide Linear Chandelier

INSTALLATION GUIDE

Tools Required (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Wire cutters, Electrical tape, Safety goggles, Ladder.
Helpful Tools: Wire Strippers
Bulb Recommended: (4) GOW Type-S medium base vintage-style bulb, Alternate (4) LED bulb.
Estimated Assembly Time: 30 – 60 minutes

Preparation:

• Identify and inspect all parts before beginning installation
• Check package contents list and diagrams below to be sure all parts are included.
• If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.

 Warnings And Cautions

• Tum off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician ifin doubt.
• These instructions are provided for your safety. Itis very important you read them completely before installing fixture. We strongly recommend thata licensed, professional electrician perform the installation.
• Disconnect fixture from power source before replacing bulbs.
• Make sure bulbs are given sufficient time to cool before removal.
• Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

INSTALLATION

NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2″

STEP 1:

a. Secure the crossbar to the outlet box (not included) with outlet box screws.
b. Tighten until snug.

Note: The preassembled mounting nipple on the crossbar should protrude outward.

STEP 2:
a. Remove lock ball from crossbar assembly.
b. Fit ceiling canopy over the nipple on crossbar assembly and secure with lock ball.

Note: The ceiling canopy should be snug against the ceiling and the lock ball.

• If not, adjust the length of the nipple on the crossbar assembly by unscrewing the preassembled hex nut.
• Then, screw the nipple in or out of the crossbar until the desired length is achieved.
• Once the ceiling canopy is secure, remove the lock ball and ceiling canopy and proceed to Step 3.

STEP 3:

a. Pass supply wires and ground wire through the rod.
b. Then thread the rod to the uppermost Fixture.
c. Hand- tighten until snug.

STEP 4:

a. Choose desired hanging length for the light fixture.
Suggested mounting height over a table or island is 30 inches from the table/island top to the bottom of the fixture.
b. Adjust the fixture chain to the desired length, removing links if needed.
c. Connect one end of the fixture chain to the fixture loop preassembled to ceiling canopy with one quick link.
d. Connect the other end of the fixture chain to the fixture loop with the remaining quick link.

Note: You may need to use pliers (not included) to open the links of Fixture Chain. If so, put a cloth over the Fixture Chain to protect the finish from the pliers.

Suggested chain length to hang fixture 30 inches above table top: 8-ft. ceiling: Two, 10 inch lengths of chain+ 2 quick links 9-ft. ceiling: Two, 22 inch lengths of chain+ 2 quick links 10-ft. ceiling: Two, 34 inch lengths of chain+ 2 quick links

Note: If mounting over an Island, subtract 6 inches from the chain lengths listed above.

STEP 5:

a. The lanyard is provided as a means to support the fixture from the junction box while connecting the electrical wires. This enables the fixture to hang from the junction box and your hands are free to make the wire connections.
b. Turn the button stop so it may be inserted into the crossbar slot. Make sure the button stop is completely inside the crossbar.
c. Slowly release the fixture to make sure it is supported by the button stop.

STEP 6:

a. Confirm that the mounting height is acceptable. Refer to STEP 4 if changes are required.

Note: To make the next step easier, cut the supply wire and ground wire 24 inches longer than the distance from the fixture loop to the ceiling. Important: Please pay attention to the polarity (wires labels L & N) when cutting wires. Wire identification will be needed in STEP 7.

b. Pass supply wires and ground wire through the quick link and fixture chain in alternating links.
c. Push the ends of the supply wires and ground wire through the loop on the ceiling canopy and remove any remaining slack in the wire.
d. Trim excess fixture wire leaving a minimum of 6 inches extending beyond the edge of the ceiling canopy.
e. Separate the smooth side and ribbed side of the supply wire to about 3 inches from the end.
f. Using wire strippers, strip each wire½ inch from the end.

STEP 7:

Use Wire Connectors (supplied) to connect the wires.

a) Ground Wire:

1. Wrap supply ground wire around green ground screw on mounting bracket, no less than 2 in. from the end of the wire. Tighten ground screw.
2. Connect fixture ground wire to supply ground wire with wire connector.

b) Supply Wire:

1. Connect the supply white wire to the fixture supply wire (ribbed sided) from fixture identified with the label “N”.
2. Connect the supply black (or red) wire to the fixture supply wire (smooth side) from fixture identified with the label “L”.
3. Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the outlet box.

STEP 8:
a. Re-attach the ceiling canopy to the crossbar assembly.
The lanyard will push into the junction box when the Ceiling Canopy is Attached to the ceiling.
b. Then, attached the lock ball over the round ceiling canopy.

STEP 9:

a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.

Your installation is completed now. Restore electricity. Retain this sheet for future reference.

CARE AND MAINTENANCE

Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixture as they may damage the finish.

TROUBLESHOOTING

2. Power is off.
3. Faulty wire connection.
4. Faulty switch.| 1. Replace light bulb.
2. Make sure power supply is on.
3. Check wiring.
4. Test or replace the switch.
Fuse blows or the circuit breaker trips when light is turned on.| Crossed wires or power wire is grounding out.| Check wire connection.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>