rombica TIMEBOX 2 Wireless Charger User Manual

: June 8, 2024
: rombica

Table of Contents

rombica TIMEBOX 2 Wireless Charger
GENERAL INFORMATION
SPECIFICATION
OPERATION OF THE DEVICE
DISABLING THE ALARM
USING WIRELESS CHARGING
BATTERY REPLACEMENT
STORAGE CONDITIONS
SAFETY INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

rombica TIMEBOX 2 Wireless Charger

rombica TIMEBOX 2 Wireless Charger product

Thank you for purchasing Rombica device. Please read this user manual before use and save it for future reference

GENERAL INFORMATION

Wireless charger’s rubberized area for smartphone placement
LED indicator
LED display
Snooze buttons
2-sided backlight
Touch button for backlight control
Device setup buttons
Battery’s compartment (used to save settings and time)
DC-IN

SPECIFICATION

Input: 12V / 1A
Wireless output: 5V / 1A
Wireless charging distance: up to 5 mm
Material: plastic
In the box: adapter, user manual
Work with Qi-compatible devices.

This wireless charging device produced according to Qi standard. Please use it with Qi-friendly smartphones. If your phone is not Qi-compatible, you should use Qi-receiver (not included)

OPERATION OF THE DEVICE

BEFORE FIRST USE
Remove the protective ﬁlm from the compartment (8) by pulling the tab from the outside
ELECTRICAL CONNECTION
Connect the power supply adapter to the input (9) at ﬁrst, and to the 220V power socket then. After switching on the device, the LED indicator (2) will light up and change color several times and will go out
BACKLIGHT AND DISPLAY BRIGHTNESS ADJUSTMENT
Adjust by touch buttons

Short press: sequential switching between operating modes – max, min and turn off the LED display brightness
Short press: sequential switching between 3 brightness levels and turn off

rombica TIMEBOX 2 Wireless Charger 01

rombica TIMEBOX 2 Wireless Charger 02
A short press of the M button switches between display modes.
Current time display mode
This is the main operating mode of the device. When it is active, current time is shown on the LED display and ﬂashes :. The following settings are available in this mode:
Time and date settings. A short press on the S button switches the device to the setting mode: hours – minutes – year – month – day – exit the setting mode. Use the buttons and to select the desired values and the S button to select the next adjustable parameter. The day of the week is set automatically.
Setting the time display format. Shortly press the button to switch between 12 and 24 hour time display. IMPORTANT: if the 12 hour display format is selected, then when the current time is in the AM time interval, additional elements are not displayed on the screen. When the current time is in the PM time interval, the additional PM icon appears on the screen.
Setting the temperature display format. Press the button to switch between Fahrenheit or Celsius temperature display.
Alarm clock display mode
This mode displays the time at which the alarm is set. When switching to this mode, lights up and : stops ﬂashing on the LED display. If there is no any operation of device by user in this mode, it automatically switches to the current time display mode after a short time. In the alarm time display mode, the alarm time setting is available.
Setting the alarm time. Short press S, set the hours using buttons and , press button S again, set minutes, press button S again, set snooze time 5, 10, 15, 20, 25 or 30 minutes, pressing button S again will complete the setting.
Turn the alarm on/off. Press and buttons shortly to activate or deactivate the alarm. When the alarm is ON is displayed, and shows when it is OFF. IMPORTANT! if you turned off the alarm and switched to the current time display mode will go out.

DISABLING THE ALARM

The alarm will automatically turn off one minute after the alarm starts. Until that happens, you can:

Disable alarm – press or
Snooze alarm – push down on the device’s top cover, you will hear a click of pressing the buttons (4), and appears on the LED display. The alarm will go off again after the set snooze time. To completely turn off the alarm, use the or – the disappears.

USING WIRELESS CHARGING

Place the Qi-compatible device on the wireless charger’s surface (1). During wireless charging, the red indicator (2) ﬂashes. For some Android OS smartphones, the green indicator (2) ﬂashes when it fully charged.
When using wireless charging, please follow these rules:

The chargeable device must support wireless charging function (Qi-compatible). Do not place devices that do not support wireless charging on the wireless charger.
The receiver coil in the device to be charged must be located strictly above the surface for wireless charging (1); with the offset position of the receiver coil, charging will be performed with less power or will not be performed at all. Check with your device manufacturer for the position of the receiver coil in your device.
If the LED indicator is blinking red, the charging is not performing properly or there are foreign devices on the wireless charger’s surface. Reposition the device, removing all foreign objects from the wireless charging surface.

BATTERY REPLACEMENT

Disconnect the device from the power socket
Unscrew the compartment (8) and remove the cover
Remove the used battery
Install a new battery 1 x CR2032 observing the polarity
Replace the cover and tighten the compartment’s screw (8)
After replacing the battery, you will need to re-set the time on the LED screen.

IMPORTANT! The battery can only be installed by an adult! Use only new batteries that meet the CR2032 speciﬁcation (1 piece). Observe the polarity when installing the batteries. Do not dispose of batteries in ﬁre or leave them in direct sunlight.

STORAGE CONDITIONS

Keep the device in a dry, well-ventilated place, far from heaters and direct sunlight. Keep the device out of reach of children. Do not bite or lick device, as it may cause damage or explode the device. Children or persons with disabilities should not use the device without the supervision of responsible person.
Do not dispose with household waste! Required to dispose this electrical device at designated recycling collection point for electrical devices. It ensures that device is recycled professionally and prevents the release of the harmful substance into the environment. Make sure that device is uncharged before disposal.

SAFETY INFORMATION

Use the wall charger equipped in accessory pack or the charger with equal characteristics.
In case of breaking do not try to open and repair device by yourself. Use service center.
Avoid inﬂuence of the high humidity, dust, and dirt. Use a dry soft lint-free cloth to clean device. Not allowed to use washing or cleaning liquids.
Do not store, use device near heat sources and ﬂammable objects, during low or high ambient temperature. Charing can be done only under adult supervision. Recommended temperature is 5 to 35 ° C.
Power cord: The power socket must be earthed. Ensure that you have easy access to the power socket and the power cord. Before connecting the device to the power grid, make sure that the power cord and electrical socket are not damaged and have tight contact.
Never pull the cord to disconnect the cable, pull the plug.
Not allowed to drop or hit device.
Disconnect the wireless charger from the wall charger after use.
Do not insert foreign objects into the device ports.
Do not cover working device with cloth or other material.
Do not try to charge your device by the wireless charger, if your device doesn’t support Qi protocol
Magnetic ﬁelds from the wireless charger can damage bank cards. To avoid damage do not keep your bank card near working wireless charger.
If you are using external Qi-receiver (adapter that allows to charge a non-Qi device with wireless charger), please connect it to your device at ﬁrst. Do not place non connected Qi-receiver onto wireless charger.
Take a break from using if the wireless charge overheats.
The wireless charge can affect wireless networks with low-level signal.
Do not place on the working wireless charger device with connected USB cable. Disconnect all cables from your device before charging it by the wireless charger.
Note that in case there is a thick case on a device, wireless charging may not work.