rombica BH-T014 MySound Spirit White True Wireless Earbuds User Manual

BH-T014 MySound Spirit White True Wireless Earbuds
User Manual

TRUE WIRELESS EARPHONES
my sound Spirit White……………..ID: BH-T014
my sound Spirit Black………………ID: BH-T015

USER MANUAL

Thank you for purchasing the Rombica device. Please read this user manual before the operation and save it for the future.

SPECIFICATION

Power: DC 5V, from the battery
Bluetooth version: 5.0
Built-in microphone: yes, in each earphone
Frequency range: 20 Hz — 20 kHz
Driver power: 3 mW
Driver diameter 10 mm
Sensitivity: 97 dB ± 3 dB
Impedance: 32 Ohm
Battery (earphones): 30 mAh / 3.7 V
Battery (case): 250 mAh 13.7 V In the box: earphones, charging case, USB cable, manual

GENERAL INFORMATION

1. Earphones magnetic contacts
2. Earphones LED indicator
3. Earphones control button
4. Charging case-control button
5. Charging case LED indicator
6. Micro-USB port
7. Charging case magnetic contacts

TECHNICAL CHARACTERISTICS AND APPEARANCE MAY BE CHANGED WITHOUT PRIOR NOTICE

OPERATION OF THE DEVICE

POWER ON
Earphones will automatically turn on when you take them out of the charging case’
POWER OFF
Earphones will automatically turn off when you put them in a charging case. For turning off manually press and hold the control button on both of the earphones for 8 seconds. if the charging case is discharged – the earphones will not power on automatically. For turning it on manually press and hold the control button on both of the earphones for 3 seconds. Turned-on LED indicators on earphones will confirm power on

PAIRING VIA BLUETOOTH

1. Take earphones out of the charging case.
2. Two earphones will pair with each other automatically.’ When earphones are paired with each other LED indicators on them are flashing blue and red. When earphones finish pairing with each other LED indicator on one of the earphones turns off.
3. Open Bluetooth settings on your smartphone PC, enable Bluetooth, and search for new devices. When Bluetooth earphones will be found, confirm pairing.
4. After successful pairing both the Bluetooth headphones and your device, you can control playback by earphone buttons.

‘If the pairing doesn’t happen – reset your earphones and try again
MONO USE
You can use only one earphone if needed.

1.  Take the earphone you prefer to use out of the charging case.
2. The earphone will be in pairing mode automatically.’
3. Open Bluetooth settings on your smartphone PC, enable Bluetooth, and search for new devices. When Bluetooth earphones will be found, confirm pairing.
4. After successful pairing both the Bluetooth headphones and your device, you can control playback by the earphone button.

If it doesn’t happen – reset your earphones and by again

FUNCTION OVERVIEW

You can control the earphones with earphones control buttons.
Play / Pause : short press on any of the earphones
Play next song : Press and hold for 3 seconds on the right earphone
Play previous song: press and hold for 3 seconds on the left earphone
Increase volume: quick double press on the right earphone Decrease volume: quick double press on the left earphone
Receive incoming call/finish call : short press on any earphones during incoming call
Reject incoming call: long press on any earphones during incoming call
Turn on voice assistant: quick triple press on any of the earphones “Turn on Voice Assistant function works on default settings on IOS and Android operation systems. This function may not work on some of the devices

EARPHONES RESET

If earphones can’t connect to each other or to your device, or only one earphone has sound — you can reset your earphones.

1. Press and hold the control button on both of the earphones for 3 seconds to turn off the earphones.
2. Press and hold the control button on both of the earphones for 3 seconds again to turn on the earphones.
3. The reset is finished.

EARPHONES CHARGING

To charge earphones put them in the charging case and close the case. Magnetic contacts on earphones should match with magnetic contacts on the charging case. The LED indicator on both earphones is red while charging and turns off when the battery is fully charged.

CHARGING THE CASE

Before first use, fully charge Bluetooth earphones within 6 hours. A new battery requires 2-3 full charge-discharge cycles to reach full capacity. Use (supplied) cable and connect it to the Bluetooth earphones by the Micro-USB side. Connect the USB cable to the PC or wall charger (wall charger is not supplied). The charging case LED indicator blinks blue while charging and stop blinking when the battery is fully charged. The charging case LED indicator shows you the remaining capacity of the charging case’s battery:

To turn on the charging case LED indicator short press the charging case-control button.

SAFETY INFORMATION

1. Before charging be sure that the voltage of the power is 5V. The recommended adapter is 5V / 1000mA.
2. If the device is not used for a long time, charge it at least once per month.
3. In case of breaking do not try to open and repair the device by yourself. Use the service center.
4. Avoid the influence of high humidity, dust, and dirt. Use a dry soft lint-free cloth to clean the device. Not allowed to use washing or cleaning liquids.
5. Do not store, use or charge the device near heat sources and flammable objects, during low or high ambient temperatures. Charging can be done only under adult supervision. Recommended temperature is 5 to 35 °C.
6. Not allowed to drop or hit device.
7. Do not insert foreign objects to the device interfaces.
8. Turn off the device after use.
9. Never pull the cord to disconnect the cable, pull the plug.
10. TWS earphones are not intended for commercial use.
11. Standard battery life is 500 charge-discharge cycles. After exceeding 500 cycles the effective capacity of the battery can be reduced. Effective capacity also depends on the ambient temperature.
12. Keep the charging case closed when you store the device.

STORAGE CONDITIONS

Keep the device in a dry, well-ventilated place, far from heaters and direct sunlight. Keep the device out of reach of children. Do not bite or lick the device, as it may cause damage or explode the device. Children or persons with disabilities should not use the device without the supervision of the responsible person.
Do not dispose of household waste! Required to dispose of this electrical device at a designated recycling collection point for electrical devices. It ensures that the device is recycled professionally and prevents the release of the harmful substances into the environment. Make sure that the device is uncharged before disposal.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>