SDC Ossia-NVR5 8 Ch “4 In 1” Standalone Hybrid User Manual

June 3, 2024
SDC

Ossia-NVR5 8 Ch “4 In 1” Standalone Hybrid

1

Notes
Please read this user manual carefully to ensure that you use the device correctly and safely. There may be incorrect info or printing errors in this manual. Updates and corrections will be made into the future versions of this manual. The content of this manual is subject to change without notice. The device should be operated using only the type of power source indicated on the marking label. The power voltage must be verified before use. Do not install this device near any heat sources such as radiators, heat registers, stoves or other devices that produce heat. Do not install this device near water. Clean only with a dry cloth. Do not block any ventilation openings and ensure proper ventilation around the device. Perform a safe power off before disconnecting from power. This device is for indoor use only. Do not expose it to rainy or moist environments. In case any solid or liquid get inside the device’s case, turn off the device immediately and get it checked by a qualified technician. Do not try to repair the device by yourself without technical aid or approval. When this device is in use, the relevant contents of Microsoft, Apple and Google may be shown. The ownerships of trademarks, logos and other intellectual properties related to Microsoft, Apple and Google shall belong to the above-mentioned companies. This manual is suitable for all NVR/DVR models running Ossia OS. Clear markings will be made if some models do not support any of the features. All examples and pictures used in the manual are from one of the models for reference purpose. For devices with internal power supply, please make sure that the AC 220/110V input selector is set correctly
1

Basic Operation Guide

User Manual

Contents
Contents ……………………………………………………………………………………………………………………. 2
1 Introduction ……………………………………………………………………………………………………. 6
1.1 Summary ……………………………………………………………………………………………………….. 6 1.2 Features …………………………………………………………………………………………………………. 6 1.3 Front Panel Descriptions ………………………………………………………………………………….. 9 1.4 Rear Panel Descriptions …………………………………………………………………………………. 10 1.5 Connections………………………………………………………………………………………………….. 12
2 Basic Operations Guide …………………………………………………………………………………. 14
2.1 Startup & Shutdown ………………………………………………………………………………………. 14 2.1.1 Startup ……………………………………………………………………………………………….. 14 2.1.2 Shutdown …………………………………………………………………………………………… 14
2.2 Remote Controller …………………………………………………………………………………………. 15 2.3 Mouse Control………………………………………………………………………………………………. 16 2.4 Text-input Instruction …………………………………………………………………………………….. 16 2.5 Other Button Operations ………………………………………………………………………………… 16
3 Wizard & Main Interface ………………………………………………………………………………. 17
3.1 Startup Wizard………………………………………………………………………………………………. 17 3.2 Main Interface ………………………………………………………………………………………………. 23
3.2.1 Main Interface Introduction…………………………………………………………………… 23 3.2.2 Setup Panel…………………………………………………………………………………………. 25 3.2.3 Main Functions……………………………………………………………………………………. 26
4 Camera Management…………………………………………………………………………………….. 27
4.1 Camera Signal (Applicable only for DVRs)………………………………………………………. 27 4.1.1 Dynamic Hybrid (Supporting devices only) …………………………………………….. 27
4.2 Add/Edit Camera …………………………………………………………………………………………… 28 4.2.1 Add Camera (Applicable only for NVRs and Hybrid DVR models) ………….. 28 4.2.2 Edit Camera’s General Parameters …………………………………………………………. 31
4.3 “In-Channel Sequence” (Only Applicable for NVRs) …………………………………………. 33 4.3.1 Add “In-Channel Sequence”………………………………………………………………….. 33 4.3.2 Edit In- Channel Sequence …………………………………………………………………….. 33
4.4 IPC Networking (Applicable only for NVRs and Hybrid DVR models) ……………….. 33 4.4.1 IP Camera management………………………………………………………………………… 34 4.4.2 Device Management…………………………………………………………………………….. 34
5 Live-view Introduction: …………………………………………………………………………………. 35
5.1 Live-View Interfaces: …………………………………………………………………………………….. 35 5.2 Fish-Eye Display:………………………………………………………………………………………….. 36 5.3 Live View Digital Zoom: ……………………………………………………………………………….. 37 5.4 Live-View Modes:…………………………………………………………………………………………. 37
5.4.1 Customized Display Mode ……………………………………………………………………. 37 5.4.2 Sequence ……………………………………………………………………………………………. 38 5.4.3 In Channel Sequence (Applicable for NVRs only)……………………………………. 40 5.4.4 Face Recognition (Applicable for Face Recognition NVRs only)……………….. 41
2

Basic Operation Guide

User Manual

5.5 Emergency Live-View:…………………………………………………………………………………… 42 5.6 Image Configuration ……………………………………………………………………………………… 43
5.6.1 OSD Settings ………………………………………………………………………………………. 43 5.6.2 Image Settings (Setting Interface) ………………………………………………………….. 43 5.6.3 Mask Settings ……………………………………………………………………………………… 44 5.6.4 Water Mark Settings (Applicable for DVRs only)…………………………………….. 44 5.6.5 Fish-Eye (Applicable for Supporting NVRs only) ……………………………………. 45 5.6.6 Image Adjustment (Live-View Interface) ………………………………………………… 46
6 PTZ………………………………………………………………………………………………………………. 48
6.1 PTZ Control Interface: …………………………………………………………………………………… 48 6.2 Preset Settings ………………………………………………………………………………………………. 50
7 Record & Disk Management ………………………………………………………………………….. 52
7.1 Record Configuration:……………………………………………………………………………………. 52 7.1.1 Mode Configuration: ……………………………………………………………………………. 52 7.1.2 Advanced Configuration……………………………………………………………………….. 54
7.2 Encode Parameters Setting……………………………………………………………………………… 54 7.3 Schedule Setting……………………………………………………………………………………………. 55
7.3.1 Add Schedule ……………………………………………………………………………………… 55 7.3.2 Record Schedule Configuration……………………………………………………………… 57 7.4 Record Mode………………………………………………………………………………………………… 57 7.4.1 Manual Recording ……………………………………………………………………………….. 57 7.4.2 Scheduled Recording:…………………………………………………………………………… 57 7.4.3 Motion Based Recording:……………………………………………………………………… 57 7.4.4 Sensor Based Recording:………………………………………………………………………. 57 7.4.5 Analytics Based Recording: ………………………………………………………………….. 58 7.5 Disk Management: ………………………………………………………………………………………… 58 7.5.1 Storage Mode Configuration …………………………………………………………………. 58 7.5.2 Disk Mode (Models supporting RAID only): …………………………………………… 59 7.5.3 Physical Disk (Models supporting RAID only):……………………………………….. 59 7.5.4 Array (Models supporting RAID only): ………………………………………………….. 60 7.5.5 View Disk and S.M.A.R.T. Information: …………………………………………………. 60
8 Search, Playback & Backup …………………………………………………………………………… 61
8.1 Instant Playback ……………………………………………………………………………………………. 61 8.2 Playback Interface Introduction ………………………………………………………………………. 61 8.3 Record Search, Playback & Backup…………………………………………………………………. 66
8.3.1 Search & Playback by Time-sliced Image ……………………………………………….. 66 8.3.2 Search, Playback & Backup by Smart Search: …………………………………………. 67 8.3.3 Search, Playback & Backup by Time: …………………………………………………….. 68 8.3.4 Search, Backup & Playback by Event …………………………………………………….. 72 8.3.5 Search & Playback by Tag…………………………………………………………………….. 73 8.3.6 Snapshots …………………………………………………………………………………………… 73 8.3.7 Backup Procedures ………………………………………………………………………………. 74 8.3.8 View Backup Status……………………………………………………………………………… 74
9 Alarm Management ………………………………………………………………………………………. 75
9.1 Sensor Alarm………………………………………………………………………………………………… 75 9.2 Motion Alarm ……………………………………………………………………………………………….. 76
3

Basic Operation Guide

User Manual

9.2.1 Motion Configuration…………………………………………………………………………… 76 9.2.2 Motion Alarm Handling Configuration …………………………………………………… 77 9.3 Analytics Configuration (Applicable for NVRs and Hybrid DVRs only). ……………… 77 9.3.1 Object Monitoring Configuration (IPC Channels Only)…………………………….. 78 9.3.2 Camera Tampering Configuration (IPC Channels Only)……………………………. 79 9.3.3 Line Crossing Configuration …………………………………………………………………. 80 9.3.4 Sterile Area Configuration…………………………………………………………………….. 81 9.3.5 Analytics Alarm Handling Configuration ………………………………………………… 81 9.4 General Fault Alarms …………………………………………………………………………………….. 82 9.4.1 General Fault Handling Settings…………………………………………………………….. 82 9.4.2 IPC Offline Settings …………………………………………………………………………….. 82 9.5 Alarm Event Notification ……………………………………………………………………………….. 84 9.5.1 Alarm-out …………………………………………………………………………………………… 84 9.5.2 E-mail………………………………………………………………………………………………… 84 9.5.3 Display ………………………………………………………………………………………………. 84 9.5.4 Buzzer ……………………………………………………………………………………………….. 84 9.5.5 Push Message ……………………………………………………………………………………… 85 9.6 Manual Alarm ………………………………………………………………………………………………. 85 9.7 View Alarm Status…………………………………………………………………………………………. 85
10 Account & Permission Management ………………………………………………………………. 87
10.1 Account Management…………………………………………………………………………………… 87 10.1.1 Add User…………………………………………………………………………………………… 87 10.1.2 Edit User…………………………………………………………………………………………… 88
10.2 User Login & Logout …………………………………………………………………………………… 88 10.3 Permission Management ………………………………………………………………………………. 89
10.3.1 Add Permission Group ……………………………………………………………………….. 89 10.3.2 Edit Permission Group ……………………………………………………………………….. 89 10.4 Black and White List……………………………………………………………………………………. 89 10.5 Preview on Logout ………………………………………………………………………………………. 90 10.6 Password Security ……………………………………………………………………………………….. 90 10.7 User Status: ………………………………………………………………………………………………… 91
11 Device Management ………………………………………………………………………………………. 92
11.1 Network Configuration…………………………………………………………………………………. 92 11.1.1 TCP/ IPv4/6 Configuration………………………………………………………………….. 92 11.1.2 Port Configuration ……………………………………………………………………………… 93 11.1.3 DDNS Configuration………………………………………………………………………….. 94 11.1.4 E-mail Configuration………………………………………………………………………….. 96 11.1.5 UPnP Configuration …………………………………………………………………………… 98 11.1.6 NAT Configuration …………………………………………………………………………….. 98 11.1.7 FTP Configuration ……………………………………………………………………………… 98 11.1.8 SNMP Configuration ………………………………………………………………………….. 99 11.1.9 View Network Status ………………………………………………………………………….. 99
11.2 Basic Configuration……………………………………………………………………………………… 99 11.2.1 General Settings ………………………………………………………………………………… 99 11.2.2 Date and Time Configuration …………………………………………………………….. 101 11.2.3 Layout settings: ……………………………………………………………………………….. 101 11.2.4 POS settings: …………………………………………………………………………………… 102
11.3 Maintenance: …………………………………………………………………………………………….. 103
4

Basic Operation Guide

User Manual

11.3.1 View Log ………………………………………………………………………………………… 103 11.3.2 Factory Default………………………………………………………………………………… 104 11.3.3 Device Software Upgrade………………………………………………………………….. 104 11.3.4 Cloud Upgrade ………………………………………………………………………………… 105 11.3.5 Backup and Restore ………………………………………………………………………….. 105 11.3.6 Auto Maintenance:……………………………………………………………………………. 106 11.3.7 View Log ………………………………………………………………………………………… 106 11.3.8 View System Information ………………………………………………………………….. 107
12 Remote Surveillance…………………………………………………………………………………….. 107
12.1 Mobile Client Surveillance………………………………………………………………………….. 107 12.2 Web LAN Access ………………………………………………………………………………………. 107 12.3 Web WAN Access ……………………………………………………………………………………… 108 12.4 Web-Client ……………………………………………………………………………………………….. 109 12.5 Web Remote Control ………………………………………………………………………………….. 110
12.5.1 Remote Live-View …………………………………………………………………………… 110 12.5.2 Remote Playback……………………………………………………………………………… 113 12.5.3 Remote Backup ……………………………………………………………………………….. 114 12.5.4 Remote Configuration …………………………………………………………………….. 114
Appendix A: FAQ…………………………………………………………………………………………………… 115
Appendix B: Calculate Recording Capacity …………………………………………………………….. 121
Appendix C: RAID Types……………………………………………………………………………………….. 122
Appendix C: Compatible Device List ………………………………………………………………………. 123

5

Basic Operation Guide

User Manual

1 Introduction
1.1 Summary
This series of devices running Ossia are designed to provide unconditional security for homes, offices, banks, schools, supermarkets, petrol service stations, residential quarters, factories, Etc. In can be accessed from local or remote locations. The Ossia OS was designed specifically to answer the user’s needs. It is based on the most advanced SOC technology and adopts a new and intuitive human GUI. This series of the devices is more powerful than any older device produced by Provision-ISR. It is easy to use while providing excellent image quality and system stability.
1.2 Features
Basic Functions Support live view, record and configuration of IP cameras Some Devices (NVR5 Series and above ­ Non-“E” models) support the latest H.265
(HEVC) video coding stream and a mixture input of H.265 and H.264 IP cameras. Ossia DVRs does not support H.265. Support standard ONVIF protocol Support dual stream recording of each camera Support IPC Quick add 4in1 Support for DVRs (AHD/CVI/TVI/CVBS) Support batch or single configuration of IP cameras (OSD, video parameters, mask, motion, alarms, Etc.) Support a maximum of 8 user permission groups including Administrator, Advanced and Ordinary which are the default permission groups of the system Support a maximum of 16 users. Support a numerous web clients login at the same time (According to device’s specs) Analytics support
Live Preview Features: 4K×2K/1920×1080/1280×1024 HDMI and 1920×1080/1280×1024 VGA high definition
synchronous display (This may vary according to your model. Please refer to your device technical specs for more information) Multi-screen modes such as 1/4/6/8/9/16/25/32 (depends on model) Auto adjustment of the camera’s image display proportion IPC audio monitoring (can be enabled or disabled)
Manual snapshot of the previewed camera Customized setting the sequence pages Support saving of the display modes. The saved modes can be called directly One channel operation tool bar Camera group view and scheme view in sequence and quick sequence view Motion detection and video masking
6

Basic Operation Guide

User Manual

Full PTZ control including setting up the presets and cruises Direct mouse control over the PTZ cameras including movement, zoom and focus. Intuitive Digital-Zoom can be controlled directly from the mouse wheel Image adjustment (only available for some cameras)
HDD Support:
3U Case support up to 16 SATA HDDs 2U Case support up to 8 SATA HDDs 1.5U Case support up to 4 SATA HDDs 1U Case support up to 2 SATA HDDs Small 1U/MM Case support up to 1 SATA HDD Each SATA interface of the device supports the HDDs with max 8TB storage capacity Some models support record and backup to an e-SATA HDD
Disk Management:
The HDDs can be grouped for configuration and management. Each camera can be added into different disk group with different storage capacity Some devices support RAID The system allows batch formatting of the HDDs
Record Configuration:
Support main stream and sub-stream recording at the same time. Batch or single configuration of the record stream Manual and auto record modes Schedule recording, sensor alarm recording and motion detection recording Configure different record streams for schedule recording and event recording setting Support record duration setting and recycle recording Support pre-alarm recording and post alarm recording configuration for event recording Support situation dependent recording.
Playback:
Time scale operation in quick playback. Also, the playback date and time can be set easily
by scrolling the mouse wheel. The intervals of the time scale can be zoomed in/out. Record searching by Image-slice/time/event/tag Time image slice searching by month, by day, by hour and by minute and time. The slice
is displayed by image thumbnail Up to 16 channels to be searched by time Event searching by manual/motion/sensor events Tag searching (for tags manually added by user) Instant playback of selected camera within the live preview interface Up to 16 synchronous playback channels
Record Backup
Backup through USB (U-disk, mobile HDD) or e-SATA** interface Backup by time/event/image searching

7

Basic Operation Guide

User Manual

Customized backup selection while playing back Up to 10 backup tasks running in the background
Alarm Management:
Alarm schedule setting Supports enabling or disabling of motion detection, external sensor alarm input and
exception alarms including IP address conflict alarm, disk I/O error alarm, disk full alarm, no
disk alarm, illegal access alarm, network disconnection alarm and IPC offline alarm. Configurable alarm trigger Alarms can trigger PTZ Operation, snapshots, pop-up videos and more. Event notification modes: Alarm-out, pop-up video, pop-up message box, buzzer and
E-mail E-mail schedule support Snapped images can be attached to the e-mail when alarm triggered Alarm information status for alarm-in, alarm-out, motion detection and exception alarm Alarm can be triggered and cleared manually System auto reboot when HDD or I/O exception happens ­ in order to restart and recover
the HDD
Network Functions:
TCP/IP and PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP, RTSP protocols “Allow & Block” lists according to IP or MAC addresses Multiple browser support for Windows and Mac OS (Must Support NPAPI Plug-ins) Remote configuration and maintenance including remote upgrading and remote system
reboot Remote camera configuration of the device including video parameters, image quality,
Etc.* Remote search, playback and backup. CMS or other management software can access the device and manage it. Support Cloud connection (NAT) and QR Code scanning by smart phones and tablets Support mobile surveillance by smart phones or tablets running iOS or Android OS Telnet function can be enabled or disabled by the user for remote maintenance
Other Functions:
The device can be controlled and operated by the supplied mouse or remote controller Standard remote Mouse can be used (Not supplied) Quick device information view including basic details, camera status, alarm status, record
status, network status, disk and backup status Support auto recognition of the display resolution

  • For NVRs, Dynamic Hybrid and Hybrid DVRs only **Supported models only
    8

Basic Operation Guide

User Manual

1.3 Front Panel Descriptions
The following descriptions are for reference only. Type I (MM/Small 1U/1.5U Models):

REC NET PWR

Name

Descriptions While recording, the light is blue When accessed by network the light is blue When powered on , the light is blue

Type II (2U Models):
Name Power HDD Net Backup Play REC AUDIO /+ P.T.Z / MENU INFO BACKUP SEARCH Exit
1-9 0/-Direction Key Multi-Screen Switch Enter USB

Descriptions When powered on, the light is blue The light turns blue when reading/writing HDD The light turns blue when the devices accesses the network The light turns blue when backing up files and data The light turns blue when playing back video When recording, the light is blue 1. Adjust audio; 2. Increase the value in setup 1. Enter PTZ mode; 2. Decrease the value in setup Enter Menu Check the information of the device Enter backup mode in live Enter search mode in live Exit the current interface Manual record Play/Pause Speed down Speed up Input digital number and select camera Input number 0, the number above 10 Change direction Change the screen mode Confirm selection To connect external USB device like USB mouse or USB flash

9

Basic Operation Guide

User Manual

1.4 Rear Panel Descriptions
In this section we will introduce you to a few samples of rear panels. Of course we cannot include all rear panels of all the available devices. Please take this manual as reference only.

No.

Name

Descriptions

1

ALARM OUT Relay output; connect to external devices

2

GND

Ground connection

3

AUDIO IN

Audio input

4

DC12V

DC12V power input

5

LAN

Network port

6

VGA

Connect to VGA monitor

7

ALARM IN

Alarm inputs for connecting sensors

8

HDMI

Connect to HD display

9

USB

Connect USB storage device or USB mouse. USB3.0 interfaces will be colored in blue.

10 AUDIO OUT Audio output

11 RS485

Connect to keyboard. A is TX+; B is TX-

10

Basic Operation Guide

User Manual

No.

Name

Descriptions

1

VGA

Connect to VGA monitor

2

e-SATA

Connect to HDD with e-SATA interface

3

RS485 Y/Z interface Unavailable

4

RS485 A/B interface Connect to keyboard. A is TX+; B is TX-

5

AUDIO OUT

Audio output

6

LAN

Network port

7

HDMI

8

USB

9

GND

Connect to HD display Connect USB storage device or USB mouse. USB3.0 interfaces will be colored in blue. Ground connection

10 ALARM OUT

Relay output; connect to external devices

11 ALARM IN

Alarm inputs for connecting sensors

12 AUDIO IN

Audio input

13 Power Switch

Press the switch to turn on/off the device

14 Power Supply

Power supply interface

No.

Name

Descriptions

1

VGA

Connect to monitor

2

RS485 Y/Z interface Unavailable right now

3

ALARM OUT

Relay output; connect to external alarm

4

GND

Grounding

5

AUDIO OUT

Audio output; connect to sound box

6

e-SATA1/ e-SATA2 Connect to HDD with e-SATA interface

7

LAN1/LAN2

Network ports

8

HDMI1

Connect to 4K×2K high definition display device

9

USB3.0/USB

USB3.0/2.0 interface, connect storage device or mouse

10 HDMI2

Connect to 1920×1080 high definition display device

11 RS485 A/B interface Connect to keyboard. A is TX+; B is TX-

12 ALARM IN

Alarm inputs for connecting sensors

13 AUDIO IN

Audio input

14 Power Switch

Press the switch to turn on/off the device

15 Power Supply

Power supply interface

11

Basic Operation Guide

User Manual

No.

Name

1

Power Supply

2

PoE port

3

LAN

4

VGA

5

HDMI

6

USB3.0

7

AUDIO IN

8

AUDIO OUT

Descriptions DC48V power supply interface 8 PoE network ports; connect to 8 PoE IP cameras Network port Connect to VGA monitor Connect to HD display (4K Ultra HD Supported) USB3.0 interface, connect USB storage device or USB mouse Audio input Audio output

1.5 Connections
Video Output Connections Video Output: Supports VGA/HDMI/CVBS/Spot video output (Depends on models). You can connect to monitor through these video output interfaces simultaneously or independently.
Audio Connections Audio Input: Connect to microphone, pickup, etc. Audio Output: Connect to headphone, sound box or other audio output devices.
Alarm Connections Only selected models support this function. See below 16 CH alarm inputs and 1 CH alarm output for example.

12

Basic Operation Guide

User Manual

Alarm Input (Availability depends on model):
Alarm IN 1~16 are 16CH alarm input interfaces. There are no type requirements for sensors. NO type and NC type are both available and can be configured from the device interface. The method to connect sensors to the device is as shown below:

The alarm input is an open/close relay. If the input is not an open/close relay, please refer to the following connection diagram:
Alarm Output (Availability depends on model):
The way to connect alarm output device: Pull out the green terminal blocks and loosen the screws in the alarm-out port. Then insert the signal wires of the alarm output devices into the port of NO and COM separately. Finally, tighten the screws. Provided that the external alarm output devices need power supply, you can connect the power supply as per the following figures.
13

Basic Operation Guide
RS485 Connection (Availability depends on model):
There are two types of RS485 interfaces:

User Manual

Type 1

Type 2

Type 1: The P/Z is for PTZ cameras ­ Not applicable for NVR devices. The K/B interface is used to connect the C06 control keyboard. Type 2: The RS485 interface is used to connect control keyboard and PTZ cameras (This connector cannot be used for PTZ control in NVR devices. A is TX+; B is TX-.

2 Basic Operations Guide
2.1 Startup & Shutdown
Please make sure all the connections are done properly before you power on the device. Proper startup and shutdown are crucial for prolonging the lifespan of the device.

2.1.1 Startup
Connect the output display device to the VGA/HDMI interface of the device. Connect the USB mouse and network cable Connect the power. The device will boot and the power LED would turn blue. A WIZARD window will pop up (you should select the display language the first time you use the device). Refer to 3.1 Startup Wizard for details.

2.1.2 Shutdown
You can power off the device by using the remote controller or USB mouse.
By remote controller: Press the power button. This will take you to a shutdown window. The unit will power off after a while by clicking “OK” button. Disconnect the power.
By mouse: Click StartShutdown to pop up the Shutdown window. Select “Shutdown” in the window. The unit will power off after a while by clicking “OK” button. Disconnect the power.

14

Basic Operation Guide

User Manual

2.2 Remote Controller (Availability depends on model):
Open the battery cover of the remote controller and insert two AAA size batteries. When placing the batteries. Please ensure the correct polarity (+ and -). Replace the battery cover.
Key points to check in case the remote doesn’t work. 1. Check batteries polarity. 2. Check if the batteries are not dead 3. Check IR controller sensor for any interference.

Button
Power Button Record Button -/– /0-9 Fn1 Button Multi Button Next Button SEQ Audio Switch Direction button Enter Button Menu Button Exit Button Focus/IRIS/Zoom/PTZ Preset Button Cruise Button Track Button Wiper Button Light Button Clear Button Fn2 Button Info Button
Snap Button Search Button Cut Button Backup Button Zoom Button PIP Button

Function
Switch off–to stop the device
To start recording Input number or choose camera Unavailable temporarily To choose multi screen display mode To switch the live image To go to sequence view mode To enable audio output in live mode No function temporarily To move cursor in setup or pan/title PTZ To confirm the choice or setup To go to menu To exit the current interface To control PTZ camera To enter into preset setting in PTZ mode To go to cruise setting in PTZ mode No track function temporarily No function temporarily No function temporarily No function temporarily No function temporarily Get information about the device To control playback. Play(Pause)/Stop/Previous Frame/Next Frame/Speed Down/Speed Up To take snapshots manually To go to search mode No function temporarily To go to backup mode To zoom in the images No function temporarily

Note: Click on the P.T.Z button to enter the PTZ interface. Once in the PTZ interface, you can use preset, cruise, track, wiper or light button to enable the relevant function.

15

Basic Operation Guide

User Manual

2.3 Mouse Control
Mouse control in Live Preview & Playback interface
In the live preview & playback interface, double click on any camera window to show the video in single screen mode; double click the window again to restore it to the previous split.
If the interfaces display in full screen, move the mouse to the bottom or to the right side of the interface to pop up the relevant tool bar. The tool bar will disappear automatically after you move the mouse away from it; Mouse control in text-input Move the mouse to the text-input box and click the box. When required to input text the keyboard will pop up automatically.

Note: The mouse is the default controller for all operations unless mentioned otherwise.
2.4 Text-input Instruction

The system includes two input keyboard layout as shown the above pictures. The left box is the number input keyboard and the right box is the general input keyboard which provides inputs of numbers, letters and punctuation characters as shown below

Button

Meaning Backspace key
Delete Key Switch key between upper and lower-case letters

Button

Meaning Switch to punctuation characters Enter key Space key

2.5 Other Button Operations

Button

Meaning Show the menu list. Change the sequence order within the list. Change the camera display mode. Close the current interface. Go to the earliest date of camera recording. Go to the latest date of camera recording.
16

Wizard & Main Interface

User Manual

3 Wizard & Main Interface

3.1 Startup Wizard

On each startup, the disk icons will be shown on the top of the interface. You can view the

number and status of each disk quickly and conveniently through these icons

No disk

Unavailable disk

R/W available disk

You can quickly and easily configure the device using the setup wizard. The wizard can also be skipped and will be shown in the next startup unless the “Enable wizard next time” was unticked. Skipping the wizard will automatically set the default password to “123456”

Click “Wizard Setup” to start. The setting steps are as follows: Admin settings. (Appears only one time ­ on the first system startup): Set your own admin password or use the default when you use the wizard for the first time (the default username is admin. skipping this part will set the default password to “123456”); It is highly advisable to change the default password.

17

Wizard & Main Interface

User Manual

Click on “Password Recovery” to set questions and answers for password recovery. If you will ever forget the password ­ these questions will be used to restore the password to factory default. Please refer to Q4 in Appendix A FAQ for details. Skipping this step will force you to contact the technical support in case the password will be forgotten. There is no other way for the user to independently recover the admin password except of this method. In this step you can also set a “Pattern” password that could be used for login into the device. It is simpler and more fluid to use the pattern lock when using a mouse and screen only (without a keyboard). If you wish to use pattern lock, enable it and click “edit” to set it as follows:

Click “Next” to continue or click “Cancel” to exit the wizard.
Date and Time Configuration. (Appears only one time ­ on the first system startup): The date and time of the system must be configured when you use the wizard for the first time. Set the time zone, system time, date format and time format. The DST will be enabled by default if the time zone selected includes DST. The “Method” line allows you to change from manual setting to NTP (Network Time Protocol) setting which will synchronize the time with the configured NTP server. The default NTP server is “provisionisr-time.com” but you can change it to any other NTP server as you wish. Click “Next” to continue.

18

Wizard & Main Interface
Network Settings – general. Check “Obtain an IP address automatically” and “Obtain DNS automatically” to get the IP address and DNS automatically (You must have a DHCP Service enabled in your network). Uncheck it in order to input it manually. Input the HTTP port, RTSP port and Server port (please see 11.1.2 Port Configuration for details). Click “Next” to continue.

User Manual

Network setting ­ PoE NVRs: If you use PoE NVR, the state of the internal ethernet port will be shown on the interface as seen on the picture below. Please refer to 11.1.1 TCP/IPv4 Configuration for detailed introduction of the internal ethernet port.

Picture reference for DVR/Non-PoE NVR

Picture reference for PoE NVR
Professional models with 2 Ethernet ports: Some devices support 2 ethernet ports. The ports can work in 2 ways ­ “Multiple Address Setting” which means that the device will get 2 IP addresses and both addresses are always active. The second option is “Network fault tolerance” which means that only the primary ethernet port is active at a given time. If the primary network develops a fault ­ the device will automatically switch to the secondary ethernet port. Please refer to 11.1.1 TCP/IPv4 Configuration for additional information.
19

Wizard & Main Interface
For “Multiple Address Setting” you will need to set 2 different addresses (Static or DHCP) and one DNS address. You can set the default ethernet port for DNS routing.

User Manual

For “Network fault tolerance” you will need to set a single address (Static or DHCP) and DNS address. The 2 networks should be in the same IP Segment. You can also set the primary ethernet card.
QR Code: You can enable the NAT service and scan the QR Code using the “Provision Cam 2” mobile application to quickly connect to the device. Please refer to 12.1 Mobile Surveillance for additional information.

Add Camera. This section is available only in NVRs and Hybrid DVRs. It is applicable

for IP cameras only. Connected analog cameras will be displayed automatically. Click

“Refresh” to refresh the list of available IP cameras and click

to add the checked camera.

Click “Add All” to add all the cameras in the list. Click “Delete All” to delete all the added cameras.

to delete the added camera. Click

20

Wizard & Main Interface

User Manual

Click

to edit the network parameters of the selected IP camera as shown on the left below.

Input the new IP address, subnet mask and gateway. Fill the current username and password of

the camera. Click “OK” to save the settings.

Click

to edit the added camera as shown on the above right. Input the new camera name,

IP address and port. Fill the current username and password of the camera. You can click “Test”

to test the effectiveness of the filled information. Click “OK” to save the settings. You can

change the IP camera name only when the camera is added and online. Click “Next” to

continue.

Disk Settings. You can view the disk status, number, capacity and serial number. Click

“Format” to format the disk. Click “Next” to continue.

Models Supporting RAID: These models will have another step ­ “Disk Mode”. Here you will be able to enable RAID. After confirmation ­ The device will prompt for a reboot.

21

Wizard & Main Interface After the reboot, there will be a new step in the wizard ­ “Create an array”

User Manual

Set the array as you wish and click “next” to continue. You can find further explanation about RAID in the appendix at the end of this manual.
Record Settings. Two record modes are available: Auto and Manual. See 7.1.1 Mode Configuration for details. Auto: Select the desired auto mode in the interface as shown below and click “OK” button to save the settings. You can use the “Advanced” button to create new combinations for recording.

Manual: After switching to manual, set the schedule for “Sensor Record”, “Motion Record” and “Schedule Record” of each camera. (You can choose all together by clicking on . Click “OK” to save the settings.
22

Wizard & Main Interface

User Manual

3.2 Main Interface
3.2.1 Main Interface Introduction

23

Wizard & Main Interface Operations bar ( ) icon description:

User Manual

Button

Meaning
Start button. Click it to pop up the menu ().
Full screen button. Click it to switch to full screen mode; click it again to exit the full screen mode.
Screen split mode buttons.
Dwell button (see 5.2.2 Quick Sequence View and 5.2.4 Scheme View In Sequence for details).
Click it to enable OSD; click to disable OSD.
Click to set the default playback time for in-channel instant playback (8.1 Instant Playback) and all channel playback (8.2 Playback Interface Introduction); click to activate quick playback for all channels ­ going back to the specified time. For instance, if you choose “5 minutes ago” as the default playback time, you can playback the record from the past five minutes.
Manual record button. Click it to enable/disable manual record.

Manual alarm button. Click it to manually trigger or clear the alarm-out

Information button. Click it to view system information.
Introduction of area : A) Click “Camera” to view all the cameras available for display. Either select one window on
the left side of the interface and double click on the camera name you wish to view in the selected window or drag a camera name from the right pane to the selected window on the left.

B) Click “In-Channel Sequence” to view all the configured “In-Channel Sequence” groups list; Select a group in the list to view all the cameras related to that group. (Refer to 4.2 Add/Edit In-Channel Sequence for detailed information). Either select one window on the left side of the interface and double click on the group you wish to view in the selected window or drag a group name from the right pane to the selected window on the left.

C) Click “Display Presets” to view your saved presets (refer to 5.2.1 Preview By Display Presets for detailed explanation of the display presets). Double click on the desired display preset from the list to activate it.

24

Wizard & Main Interface Introduction of area ():

User Manual

Icon / Button

Meaning Showing the current user name Record search and backup interface, see 8.3 Record, Search, Playback & backup for details. Playback interface .see 8.2 Playback Interface Introduction for details.
Setup panel, see 3.2.2 Setup Panel for details.
Log out of the system.
Perform “Logout”, “Reboot” or “Shutdown”

3.2.2 Setup Panel
Click StartSettings to pop up the setup panel as shown below. The setup panel includes seven categories. Each category contains sub-categories that will link you to the desired configuration interface.

Here we take Camera category as an example. The Camera Category provides links such as “Add Camera”, “Edit Camera”, “Image Settings”, “Motion” and “PTZ”. Click Camera and “Add Camera” to go to the camera management interface as shown below.
25

Wizard & Main Interface

User Manual

Click the main categories on the top of the screen to go to corresponding interface. Refer to the picture below. For instance, you can go to system setup interface by clicking “System” tag.

3.2.3 Main Functions
Camera Offers functions such as Camera Management (see Chapter 4 Camera Management for details), Image Settings (see 5.3 Preview Image Configuration for details), Motion (see 9.2.1 Motion Configuration for details) and PTZ (see Chapter 6 PTZ for details).
Record This category covers Encode Parameters and Record Schedules. Please see Chapter 7 Record & Disk Management for details.
Disk Her you will find Disk Management, Storage Mode and Disk Information. Please see Chapter 7 Record & Disk Management for details.
Alarm Configure Sensor and Motion Alarm Handling and Alarm Out Settings. Please see Chapter 9 Alarm Management for details.
Network This category contains TCP/IPv4, DDNS, Port, E-mail and Network Status. Please see 11.1 Network Configuration for details.
Account and Authority This category covers Account Management (see 10.1 Account Management for details) and Permission Management (see 10.3 Permission Management for details).
System The category shows Basic Configuration (see 11.2 Basic Configuration for details), Device Information (see 11.7 View System Information for details), Log Information (see 11.6 View Log for details) and Configuration File Import & Export (see 11.5 Backup and Restore for details).

26

PTZ

User Manual

4 Camera Management
4.1 Camera Signal (Applicable only for DVRs)
All of the DVRs sunning Ossia OS support 4in1 technology (AHD / CVI / TVI / Analog). The default setting for video signal is “Auto” which means that the DVR will automatically recognize the camera signal and device which technology it is using. In some cases, the auto recognition fails ­ which will cause the video to come up in black & white or not to come up at all. In such cases, you will have to set the signal manually. Click StartSettingsCameraCamera Signal Choose the relevant channel (By number) and set the signal to the required one (Choose out of Auto/CVI/TVI). CVBS signal will be recognized automatically in all conditions.

If the DVR support “Lite” technology, you will see a “lite” column in this window. Selection of Lite will change the recording resolution to “Lite” and change the FPS from Half-Real-Time to Real-Time.
4.1.1 Dynamic Hybrid (Supporting devices only)
Dynamic hybrid allows you to choose weather a channel will perform as an HD Analog channel or as an IP Channel. Each device supporting Dynamic Hybrid has its own capabilities and restrictions. Please refer to the device’s product specs in order to learn more on your device capabilities.
Configuring Dynamic Hybrid: Click StartSettingsCameraCamera Signal On the “Analog/IP” column, choose between Analog and IP. Confirm. Upon confirmation the device will prompt for reboot. After the reboot, the
selected channel will be as defined.
Note: Analog channels will be converted to IP even if there is a camera connected to it. IP channels till not be allowed to be converted if there is a camera configured on it.
27

PTZ

User Manual

4.2 Add/Edit Camera

4.2.1 Add Camera (Applicable only for NVRs and Hybrid DVR models)

For Non-Hybrid DVRs: the camera will be displayed automatically once connected to the BNC port. If the image does not appear on the screen please check the camera’s power supply and video connection. For NVRs and Hybrid DVRs: The device’s network parameters should be configured before adding IP cameras (see 11.1.1 TCP/IPv4 Configuration for details).

Referring to the pictures below, Click on Add Camera in the setup panel or

in the top

right corner of the preview window to pop up the “Add Camera” window as shown below. You

can use the “quick add” interface to add an IP Camera or add it manually.

28

PTZ

User Manual

Quick Add
Check mark the desired cameras and click “Add” to add cameras. Click on “Default Password” to set the default username and password per manufacturer.

Editing IP Address of Specific Camera

Must be done prior to adding the IPC. From the

“Quick Add” interface, Click

to edit the IP of

a specific IP camera. Set the IP new IP address,

subnet mask and default gateway. Input the IPC

password and confirm. After a few seconds, the

camera IP address will change.

Editing IP Address of Several Cameras
Must be done prior to adding the IPC. From the
“Quick Add” interface, Click next to the “Edit” tab and choose “Batch IP Settings”. Choose the target cameras, set the first IP Address, Subnet Mask and Default Gateway and confirm. The IPC Addresses will be set in consecutive order. Make sure that all the target IP addresses are free (For example: If you configure 32 cameras and the starting IP is 192.168.1.1, then you need to make sure that all the addresses from 192.168.1.1 to 192.168.1.32 are free)

29

PTZ

User Manual

Add Manually
IP Input: Input the IP address, port, username, password and protocol of the camera and click “Test” to confirm the settings are correct and that connection can be made with the camera. Domain Input: If you are using DDNS to connect with the camera, click on the arrow next to the IP address to switch the connection mode from IP to domain. Once finished, click the “Add” button.

Protocol / RTSP Input: The system has several built-in communication protocols with the camera (Provision-ISR, ONVIF, Hikvision, Dahua). If you wish to add a channel using RTSP, click on the drop down menu arrow next to the chosen protocol (Default is “Provision-ISR”) and choose “Manage Protocol”. The following window will appear.

Set a name for the protocol, enable it and set the values as required (Both master-stream and sub-stream values must be entered). Click OK to continue.
30

PTZ

User Manual

Add Recorder (Applicable only for NVRs)
If you wish to view/record channels from another Provision-ISR device on the network you can use this option. Click on “Add Recorder”. The following window will appear.

The NVR will display automatically all the supported devices found on the LAN with its details. If you wish to add a channel from any of the displayed devices, double click on it and then double click on the channel you wish to add.

If you wish to add a channel from a recorder located on another network, click on “Add Manually” and input the IP address, port and login credentials for the device, then click on “Test Device” if the connection is well, you will get a list of available channels. Double click on the channel you wish to add.

Click

to delete the camera. Click “Default Password” to set the default username and

password per manufacturer.

4.2.2 Edit Camera’s General Parameters
This can be done only when there are active video channels. You can use Preview button to trigger a live video stream from the camera in a pop up window for easy identification. Click “Edit Camera” in the setup panel to go to the edit interface.

Edit Camera’s name: Click

to edit the camera’s name. Set the new name and confirm.

31

PTZ
Change camera’s password (for IP cameras only): Click on the button next to “Operation” and then choose “Modify IPC Password”. In the opened window choose the desired cameras, input the new password and reenter it for confirmation.

User Manual

Delete Cameras (for IP cameras only): Click on

to delete the camera.

Update IPC Firmware (for IP cameras only): Click on
to update the camera’s firmware. After confirming the update, choose the cameras and firmware version from the opened window and confirm.

Note: If a PoE NVR is used, the IP cameras (with PoE function) which connect directly to the PoE port of the NVR will be displayed automatically in the camera list. The IP camera which occupies the PoE port has a prefix shown before its camera name. The prefix consists of PoE plus PoE port number. Cameras connected to PoE ports cannot be deleted from the camera list. IP cameras that connect directly to the PoE port of the NVR using “Provision-ISR” private protocol will be shown automatically in the camera list. One of the two conditions must be met for an IP camera that connect directly to the PoE port of the NVR using “ONVIF” protocol to be shown automatically in the camera list.
The IP camera is in the same network segment with the NVR internal ethernet port. The DHCP (Assigning IP Address automatically) of the IP camera is enabled. If the IP camera which connects to the PoE port cannot be displayed automatically in the camera list, please refer to Q6 in Appendix A FAQ for details.

32

PTZ

User Manual

4.3 “In-Channel Sequence” (Only Applicable for NVRs)
In channel sequence will run a sequence of specified cameras within a single window while in split mode. It can also be used on full screen, but will be less effective.
Add “In-Channel Sequence”
Click “In-Channel Sequence” in the interface to go to the configuration area as shown below.

Click

to pop up the window

as shown below. Set the group

name and dwell time (the dwell

time of the camera group sequence

view) in the window. Check the cameras and click “Add” to add

group. Click

to view the

cameras in the group after adding

group.

4.3.1 Edit In-Channel Sequence

Click

to modify the group information such as group name and dwell time. Click

to delete the group.

4.4 IPC Networking (Applicable only for NVRs and Hybrid DVR models)

IPC networking will allow you to remotely configure IP cameras and basic network parameters of other devices. This is applicable only for devices running Ossia v1.1 and up. Below you will be able to learn about the different options of this feature.

33

PTZ

User Manual

4.4.1 IP Camera management
The IP Camera management is identical to the “Add/edit camera” Interface. You can set the IP parameters and the name of the camera through it. Please refer to section 4.2 Add/Edit Camera for more information.

4.4.2 Device Management
Here you will be able to remotely set the general network parameters of the device and configure the IPC cameras connected to the device. The following information is available: Device name, Device current IP Address, Cameras and availability.

Clicking on

will open the device menu You wll have the following options:

· Edit IP ­ Set the device’s IP address, subnet mask and gateway. Tick the devices you wish to configure and set the start IP address. The device will set automatically the rest of the IP address. Make sure that the whole segment is available before running this procedure. Set the subnet mask and gateway ­ this will be set for all devices. Set the username and password for the devices. If any of the devices have a different password, it should be set independently otherwise the procedure will fail. Click OK to start the process.

· Edit user ­ set the admin address for the specified device. This is only required if the device password is different than the default password (admin / 123456). Tick all the relevant devices and set the user name and password
· Buzzer ­ the buzzer will help you identifying the device you wish to configure by activating the buzzer on the unit itself.
· Delete all ­ will delete all IP cameras set on the device.
34

PTZ

User Manual

Click on to open a list of all cameras connected to the device. Click on

to hide it.

Once the list is open, you can delete specific IP cameras by pointing on it and clicking on the

icon that appears. To add a specific camera to the device, choose the device and add cameras from the IPC interface on the left. Make sure that you set the user credentials beforehand.
5 Live-view Introduction:

5.1 Live-View Interfaces:
You must have active video channels for this interface to be active (see 4.1.1 Add Camera for details). Refer to the inter face as shown below to learn about the live view interface.

Live view indicators (Will appear only when a channel is active) Indicator Meaning
Active Motion detection Active Analytics detection Motion Recording On Schedule Recording Sensor Recording Manual Recording Analytics Recording Indicating that the channel support PTZ operations Indication that the audio stream for the channel is enabled “No Signal” for Analog Cameras. “Not Available” for IP Cameras
35

PTZ

User Manual

Click on the live-view window to show the channel tool bar as shown in area . Right click on the preview window to show the channel menu list. The tool bar and menu list are explained in the table below.

Button

Menu List

Meaning

Move tool. Click and drag it to move the tool bar.

Manual Record On Instant Playback
Enable Audio + Volume Control
Snap PTZ Control Zoom In Fish Eye

Start/Stop manual recording for the specific channel.
Start Instant playback for the specified channel. The playback will commence within the selected window. See 8.1 Instant Playback for details.
Enable/disable audio from the selected cannel (Requires camera/channel to support of this feature). Once enabled, a volume slider will appear to control the output volume.
Take a snapshot and open a snapshot pop-up. Click “Save” in the window to save the image. Click “Export” to export the image. Switch to the PTZ control interface. See Chapter 6 PTZ for details. Switch to the digital zoom interface. Digital Zoom can also be achieved by placing the mouse cursor on the required object and using the mouse scroll wheel to zoom in & out.
Open Fish-Eye display controls. Refer to 5.2 Fish-Eye Display

Switch to the image adjustment interface. Refer to 5.3.4 Image Adjustment for details.

Face Recognition

Camera Info

5.2 Fish-Eye Display:

Open audio out (Talk)
Supporting Devices Only will display the face recognition interface button. If the camera doesn’t support face detection, this icon will be grey.
View the camera information.

Fish eye cameras are usually installed to cover large areas and provide a 360° view. In order to dewarp the image properly, you need to set the installation method and the view you wish to get. Click on the “Fish Eye” Icon to get the following pop up: Choose the installation mode out of Ceiling, Wall and Desktop. Setting the installation mode wrong will result in wrong view of the video.
Now choose the display mode out of the following:

  1. Fish-Eye: Normal view of the warped fish eye sphere view.

  2. Panorama: A stretched view of the sphere removing all the

black borders.

  1. 360° view: See 2 180° views side by side

  2. Fish-Eye + 3PTZ: Normal view of the warped fish eye sphere view + 3 Digital PTZ that

can be dragged and moved using the mouse.

36 Note: Changing the Fish-Eye display mode doesn’t affect the recording of the camera.

PTZ

User Manual

5.3 Live View Digital Zoom:

Digital Zoom can be achieved by one of two methods: The first and more intuitive one is the

mouse scroll wheel. Just left click on the channel you wish to control, point the mouse cursor

on the object you want to zoom on and scroll the mouse wheel up or down to zoom in or out.

The second method is by the digital zoom interface. The digital zoom interface is shown below.

Press and drag the red box to select the zoom area. Click

/

to zoom the image.

Click the camera selection box to select other cameras for amplification. Click “Back” to return

to the live preview interface.

5.4 Live-View Modes:
5.4.1 Display Modes Tabs
The system offers several display modes. In the latest version, the only available tab is “Camera” by default. If you wish to edit the view option tabs, click on the ” ” button at the top right corner of the screen and choose which tabs you wish to activate/disactivate.
5.4.2 Customized Display Mode
Set different screen split modes and camera layouts as required and save the display to create a preset. Refer to the picture below. Double click on the display preset from the list to activate it.

37

PTZ

User Manual

Add Customized Display:
Method One:
Click “Customized Display Modes” in the main interface Set the screen split mode. Add and organize the cameras as desired. Click the “Save” button under the display presets list Enter the display preset name in the popup window and click “OK” to save it.

Method Two:

Click StartSettingsSystemBasicLayout Settings

Click

to add a new layout.

Choose the screen split mode from the bottom.

Double click the camera or camera group in the list to add them to the selected window.

Click to save the defined output as a preset (refer to 5.2.4 Scheme View In Sequence

for detailed configurations). The saved preset will be displayed in the display preset list in the

live-view interface.

Using method two will affect the sequence settings ­ please refer to 5.3.2 Sequence for

additional information.

Edit Customized Displays
Click “Customized Display” tab in the live-view interface. Select the required display from the list. Click “Rename” to edit the display mode name; click “Delete” to delete the display mode.
5.4.3 Sequence
The sequence view will automatically switch between cameras in specified times. If a customized scheme has not been created, it will keep the split layout and go through all of the available cameras. If the scheme has been created ­ the sequence will run through the created scheme. Controlling the sequence will be done from the sequence control icon as shown below.

“Running Sequence” Icon

Sequence Control
38

PTZ

User Manual

Sequence Scheme Settings
Click StartSettingsSystemBasicLayout Settings to go to the interface as shown below. Area displays all the schemes; area shows the camera layout; area displays all the cameras and groups; area is the tool bar ( : clear button; : favorite button, click it to save the layout as preset).

Add Scheme

Click

in area to create a new scheme. Click

scheme to delete it.

on the top right corner of the

Configure Scheme
a) Select a scheme in area and the screen split mode button from area . b) Drag cameras from the camera list to the desired window in area . The camera or group
will be added into the selected window. c) You can click the right-click on a camera and click “Clear” to remove a single camera or
click to remove all the cameras. d) Click “Apply” to save the settings.

Start Sequence View

Go to the live-view interface and click

to pop up a little window. Set the dwell time for

each window and click

to start the sequence. Double click the sequence view interface to

pause the view; double click again to restore the view. Click

to stop the view.

39

PTZ

User Manual

5.4.4 In Channel Sequence (Applicable for NVRs only).
You can start “In-Channel Sequence” only if a camera group was created. (See 4.2.1 Add “In-Channel Sequence” for details). Go to the live-view interface and select a camera window.

Double click one the “In-channel Sequence” group on the right side of the interface. The cameras in the group will start sequencing one by one in the selected camera window. You can also drag the group directly to any preview window. Right click on the view window and click “Close Dwell” button to stop the sequence.

40

PTZ

User Manual

5.4.5 Face Recognition (Applicable for Face Recognition NVRs only).

The Face recognition tab will open the face recognition display for all face detection cameras

Detection Time

Group Color Person Name

Detection Snapshot

Database Snapshot

Camera Name

Similarity in %

configured on the system. The pane and its controls are as follows:

5.4.6 Controls and settings:

The face recognition has 2 important settings that can be configured from the face recognition pane: 1) Similarity: Similarity means the certainty of the system that the recognized face is correct.
For example: 100% Similarity means that the system is 100% sure that the recognized person is correct.

41

PTZ

User Manual

  1. Enable Face Tracking Box: a cosmetic addition to see the identified face on the live image in real-time. This setting has no effect on the face recognition capabilities and it will work with this option enables or disabled.

Face recognition interface controls:

Button

Menu List Meaning Add to Database: Add a person to the database

Search: Search for the person in the past day

Instant Playback: Playback the detection moment

General Info: Get the detection info

5.5 Emergency Live-View:
In some cases you will have to go back to the live-view interface as soon as possible. Doesn’t matter where you are in the system or what you are currently doing. The “Emergency Live-View” was designed just for that. From any place in the system, click on the middle mouse button to activate the “Emergency Live- View”. This will take you back to the last live view display you were viewing. Please note: Using the “Emergency Live-View” during configuration will exit the configuration window and discard any unsaved changed you have made.
42

PTZ

User Manual

5.6 Image Configuration
5.6.1 OSD Settings
Click StartSettingsCameraImageOSD Settings to go to the interface shown below. Select the camera, input the camera name (or double click the camera name in the camera list to edit the camera’s name), enable or disable the name and time OSD (if enabled, drag the red name and time OSDs in the image view area to change the OSDs’ display position) and select the date and time formats. Click “Apply” to save the settings.

5.6.2 Image Settings (Setting Interface)
Click StartSettingsCameraImageImage Settings. Select the camera and set the image brightness, contrast, saturation and hue. For advanced settings you click on the arrow under the “Advanced” tab. Only cameras connected by “Provision-ISR” protocol will support advanced features. You can click “Default” button to restore the image settings to the default factory settings.

Note: Different IP Cameras will support different Image configuration features.
43

PTZ

User Manual

5.6.3 Mask Settings
Some areas of the image can be masked for privacy. Up to four mask areas can be set for each camera. (Only for Provision-ISR Cameras non-ONVIF cameras). Click StartSettingsCameraImageMask Settings to open the interface as shown below. Select the camera and enable the mask. Click “Draw” button and drag the mouse on the image area to set the mask area; click “Delete” button to delete the mask areas; click “Apply” to save the settings.

5.6.4 Water Mark Settings (Applicable for DVRs only)
Water marks are used to identify a recorded clip and reduce the probability that it has been tampered with. The Water mark will be added on top of the video clip and it can be removed while playing back and even while watching a “.dat” file backup using the RSAP player. To configure the water-mark, please follow the following steps: 1) Click Start Settings CameraImageWater Mark. 2) Choose the channel you wish to set. 3) Set “Water mark” to “On”. 4) Input the text you wish to appear as watermark. (Up to 15 characters. Only letters and
numbers are allowed) and confirm. 5) Click “Apply” to save the settings.
44

PTZ

User Manual

When playing back the specified camera, you will be able to enable/disable the water mark from showing. Watermark Disabled
Watermark Enabled
5.6.5 Fish-Eye (Applicable for Supporting NVRs only)
Fish-Eye Settings will allow you to set the installation way of the fish-eye camera in order to get the proper dewarping. 1) Click Start Settings CameraImageFish Eye.
Here you can set the installation mode and your preferred view mode. Make sure that the installation mode is set properly for the image to be displayed correctly.
45

PTZ

User Manual

5.6.6 Image Adjustment (Live-View Interface)
Go to live-view interface. Choose the channel by clicking on the desired and click on button from the tool bar under the camera window to switch to the image adjustment interface.

Image Adjustment Drag the slider to set the image brightness, contrast, saturation and hue values. Check Sharpness, WDR and DNR to enable it and drag the slider to set their values. Click “Default” button to set these parameters to their default values. The introductions of these parameters are as follows:

Parameter Brightness Contrast Saturation Hue Sharpness
WDR
DNR

Image brightness level

Meaning

The color difference between the brightest and darkest parts.

The intensity of colors, expressed as the degree to which it differs from white. Color levels of the image. Relates to the sharpness level of the image and the image edges.

WDR (Wide Dynamic Range) function helps the camera provide clear images even under extreme light conditions. When there are both bright and dark areas in the field of view, WDR balances the brightness level of the whole image and provide clearer image.
DNR (Digital Noise Reduction): decreases the noise levels and making the image smoother. Increasing the value will increase the noise reduction but it will reduce the image resolution and details.

Notes: 1) Different IP Cameras will support different Image configuration features. 2) Some cameras have more than one settings page. You need to switch pages
in the bottom of the image adjustment area.

46

PTZ

User Manual

Parameter

Meaning

White Balance

Automatically adjust the color temperature according to the environment. Can also be set manually.

Image Mirror Mirror the video image right and left.

Image Flip

Flip the video image upside down.

Lens Control (IP Cameras only. Must be supported by the camera ­ MVF Model):

Select the camera and click “Lens Control” to go to lens control tab. Click

or

to

adjust the zoom and focus parameters of the camera’s lens. Click “Save” to save the settings.

The introductions of these parameters and buttons are as follows:

Button/Parameter
Focus Mode
Re-focus when camera switches between day/night

Meaning

Click

/

to zoom in/out.

If manual mode is selected, focus button, “One Key Focus” and “Day/night mode switch autofocus” will be available; If auto mode is selected, the time interval setup will be available.

Click

/

Instant Focus

to increase/decrease the focal length.

If checked, the lens will focus automatically when the camera switches between day/night modes.

Note: This function is only available for the models with motorized VF (MVF) lens.

47

PTZ

User Manual

6 PTZ

6.1 PTZ Control Interface:

The device supports full control over dome or PTZ cameras (Via CoC/RS-485 for all types of

DVRs and via private or ONVIF Protocol for NVRs and Hybrid DVRs only.

Click on the desired camera and on the

icon from the channel tool bar. The live view will

switch to the PTZ control interface as shown below. You can select another IP dome or PTZ

from the dropdown menu on the top right of the PTZ interface.

Introductions of the interface buttons:
Button

Meaning

/

/

/

/

/

/

/

to rotate the dome. Click

to stop rotating the dome.

/

to zoom in / out.

/

to increase / decrease the focal length.

/

to increase / decrease the aperture.

Drag the slider to adjust the movement speed.

/

/ to start / stop manual recording.

/

/ to hide / show the analog joystick.

Return to the live view interface.

48

PTZ

User Manual

Analog Joystick Control

  1. The analog joystick on the left side of the interface provides quick PTZ control. The dome or PTZ will move when you drag the analog joystick. The further you drag the analog joystick from the middle of the image, the faster the dome or PTZ will move. The dome or PTZ will stop rotating when you release the analog joystick or move it to the middle.
  2. Click and hold the left mouse button to zoom in 3) Click and hold the right mouse button to zoom out

Preset Settings

Presets can be used to save important locations and recalling it quickly when needed.

As default, the preset list is empty so you will have to add and configure the presets that are

important to you.

  1. Click “Preset” to go to preset operation tab and click “Add” button to pop up a setting window

as shown below. Select the desired preset

number and input the preset name. Click “OK”

to save the settings.

  1. Adjust the camera direction and click “Save Position” to save the current preset position on the selected preset. You can also go to

preset setting interface for preset setting, see 6.2 Preset Setting for details.

  1. Click

in the preset list to call the preset; click “Delete” button to delete the selected

preset.

  1. You can add up to 255 presets for each supported camera.

Cruise Settings

Cruises are built from a sequence of presets and are used for creating a specified patrol

between presets for an endless duration (Cruise will run until you will stop it, or move the

camera). Therefore, you must save the desired presets before creating a cruise.

  1. Click “Cruise” to go to cruise operation tab and click “Add” button to open the settings window

as shown on the right.

  1. Input the cruise name and click “Add preset” to pop up the “Add Preset” window as shown

above on the right.

  1. Select the preset name, dwell time and preset speed and click “OK”. 4) In the “Add Cruise” window, you can click

to redefine the checkpoint. Click

to

delete the preset. 5) Click “Add” button to save the cruise.

  1. You can also go to cruise setting interface for

cruise setting, see 6.3 Cruise Setting for details.

49

PTZ

User Manual

  1. You can add 8 cruises for each dome at most.

In order to activate the cruise, click

to start the cruise and click

to stop the cruise.

Any movement or other command sent to the camera from the PTZ interface will stop the cruise as well. Click “Delete” button to delete the selected cruise.

6.2 Preset Settings
Click StartSettingsCameraPTZPreset to go to the interface as shown below.

Add preset

Select the desired camera and click “Add” button to add preset; or click

in the camera list

on the right side of the interface to display the preset information of the camera and click

to add preset. The operations of the “Add Preset” window are similar to that of the

PTZ control interface; please see 6.1 PTZ Control Interface Introduction for details.

Edit preset

Select camera and preset. You can input the new name of the preset and click

to save the

new preset name. Adjust the rotating speed, position, zoom, focus and iris of the preset and

click “Save Position” to save the preset.

Delete Preset Select camera and preset and click “Delete” to delete the preset.

50

PTZ

User Manual

Cruise Setting Click StartSettingsCameraPTZCruise to go to the interface shown below.

Add Cruise

Click

in the camera list on the right side of the interface to display the cruise information

of the camera and click

to add cruise. The operations of the “Add Cruise” window

are similar to that of the PTZ control interface; please see 6.1 PTZ Control Interface

Introduction for details.

Edit Cruise

Select the camera and cruise in the “Cruise” interface. Input the new cruise name and click

to save the cruise name. Click “Add Preset” to add preset to the cruise. Click

to

delete the preset from the cruise. Click a preset in the preset list and click

to move the

preset down the list and click

to move the preset up the list. Click

to start the cruise

and click

to stop it.

Delete Cruise

Click

in the camera list on the right side of the interface to display the cruise information

of the dome and click

on the top right corner of the cruise to delete it.

51

Record & Disk Management

User Manual

7 Record & Disk Management
7.1 Record Configuration:
7.1.1 Mode Configuration:
Please format the HDDs to enable recording (refer to 7.5 Disk Management for details).

The Ossia recording interface was redesigned to be clearer and easier to configure. It is based on statistics showing that most users configure the recording to work all year long in 24×7 schedule ­ the “Auto” mode is the best choice for these users. “Manual” mode is for users who wish to customize the recording/schedule configuration.
Click StartSettingsRecordMode Settings to go to the mode settings interface.
Auto Mode: The standard setting will include the following presets:
Motion Record: Record will start upon Motion Alarm under 24×7 schedule for all channels. Sensor Record: Record will start upon Sensor Alarm under 24×7 schedule for all sensors. Motion Record + Sensor Record: Record will start upon Motion or Sensor Alarms under 24×7 schedule for all channels and sensors. Always (247) Record + Motion Record: All the channels will be recorded continuously. Motion alarms will be marked in the event list and trigger “Event Record”. Always (247) Record + Sensor Record: All the channels will be recorded continuously. Sensor alarms will be marked in the event list and trigger “Event Record”. Always (247) Record + Motion Record + Sensor Record: All the channels will be recorded continuously. Motion and sensor alarms will be marked in the event list and trigger “Event Record”.
Always (247) Record + Motion Record + Sensor Record + Analytics Record: All the
channels will be recorded continuously. Motion, sensor and analytics alarms will be marked in the event list and trigger “Event Record”.

52

Record & Disk Management

User Manual

If you wish to create a personalized combination, click on the “advanced button to open the advanced menu: The advanced menu allows you to create any combination you require (As long as it is not currently available in the standard menu). Tick the recording triggers you wish for the combination to have and click on “add” to continue. The new combination will be added as a new line to the standard menu. Only one customized combination can be used. If you wish to edit it, click on the advanced button once again and change the selected triggers.

Selecting one of the auto modes will pop up the stream settings window as shown below. Set the video encode type, resolution, FPS, bit-rate type, bitrate and audio for each of the camera and click “OK” to save the settings. It is recommended to follow the bit-rate recommended by the system in the “Bit-Rate Limit Recommended Range” Tab. Important: In case you chose one of the continuous modes, make sure to configure both “Normal” and “Event” settings.

Video Encode: the available options are H.265 and H.264. H.265 must be supported by the device and IP camera for this encoding mode will be available. GOP: Stands for “Group of Pictures” and required for efficient decoding. Keep as configured unless required otherwise. Resolution: the higher the resolution, the bigger the image. FPS: Higher frame rate delivers more fluency. However, more storage space will be required. Bitrate Type: Choose between CBR (Constant Bit-Rate) and VBR (Variable Bit-Rate). Bitrate: bitrate stands for the compression aggressiveness. The lower the bitrate, the higher the compression. High compression means lower bandwidth and storage space usage, but also decreasing the video quality. Recommended Bitrate Range: The system will show a range of bitrates that balances between quality and bandwidth/storage consumption according to the configuration you set. It is recommended to follow this recommendation. Audio: Select weather to record audio or not for the chosen channel.
53

Record & Disk Management

User Manual

Manual Mode
If manual mode is selected, you will need to set the encode parameters and schedules for each of the cameras. See 7.2 Encode Parameters Setting and 7.3 Schedule Setting for details. Failing to do so will result in recording inconsistency or complete lack of recording.

Note: Only NVRs and Hybrid DVRs will have the “Analytics” Option.

7.1.2 Advanced Configuration
Click StartSettingsRecordAdvanced to go to the following interface. Enable or disable cycle and sub-stream recording, set the pre-alarm record time, post- alarm record time and expiration time of each camera and click “Apply” to save the settings.

Cycle recording: The recording will work in FIFO method ­ First in first out ­ meaning that the oldest recording will be overwritten by new recording once the HDD is full. Dual Stream Recording: Enable/Disable the sub-stream recording of the device. Important note: Disabling sub-stream recording will increase the duration of main stream recording but will dramatically reduce system performance and disable many features that rely on the sub-stream recording in order to work. Pre-alarm Record Time: set the record time duration before the alarm event started. Post-alarm Record Time: set the record time duration after the alarm event ended. Expiration Time: set the expiration time for recorded video. Recordings will not be kept longer than the specified duration even if the HDD is not full.
7.2 Encode Parameters Setting
Click StartSettingsRecordEncode Parameters to access the interface shown below. Set the video encode, resolution, FPS, bitrate type, bitrate and audio of main stream for each of the cameras. Important: this interface offers both “Event Recording Stream” and “Normal Recording Stream” configurations. Make sure to configure both. You can set the record stream for each camera set all cameras together by clicking on . Click “Apply” to save the settings.
54

Record & Disk Management

User Manual

Click StartSettingsRecordStream Settings to go to “Sub-stream” interface. Set the sub-stream video encode type, resolution, FPS, Bitrate type and bitrate for each camera or for
all cameras together by clicking on . Click “Apply” to save the settings.

7.3 Schedule Setting
7.3.1 Add Schedule
Click StartSettingsRecordRecording ScheduleEdit Schedules (Available only in manual recording mode). The pre-set schedules are “247” (All week), “245” (Weekdays Monday to Friday) and “242” (Weekends ­ Saturday & Sunday). “247” schedule cannot be deleted or modified while “245” and “242” can be edited or deleted. Click the schedule name to display the detailed schedule information on the left side of the interface. The lines on the left stand for the seven days of the week. Each line stands for the daily 24 hours. Red marks the active selection and grey marks inactive selection.

Click

to add a new schedule or

to edit an

existing one. Refer to the picture below.

Input the schedule name, set the schedule times and click “Add” to save the schedule. You can set day schedule or week schedule. -Active duration button -Inactive duration button.
55

Record & Disk Management

User Manual

Set Single Day Schedule

Click

and drag the mouse cursor on the time scale of a specific day to mark the active

duration. Click

and drag the cursor on the time scale of a specific day to make a selected

area inactive.

You can manually set the record start time and end time: select “Manual” from beneath the day bar and set the desired time. Click “Ok” to confirm.

Click “All” to set all day recording; click “Reverse” to swap the marked and unmarked areas; Click “Clear All” to clear all the selected area in a day. After completing a setting for any day you can click “Copy To” from beneath the day bar to copy the selected schedule to other days. Refer to the picture below. After clicking on “Copy To” from the source day, check the destination days in the window and click “OK” to save.

Set Multi-Day Schedule

Use “Manual” beside

to set the weekly schedule. Refer to the picture below. Set the start

and end time, check the days in the window and click “OK” to save the settings.

Click “All” to set all week recording; click “Reverse” to swap the selected and unselected time in a week; click “Clear All” to clear all the selected area in a week.
56

Record & Disk Management

User Manual

7.3.2 Record Schedule Configuration
Click StartSettingsRecordRecording ScheduleSchedule Configuration to go to the interface shown below. Define the schedule for sensor, motion, analytics, POS and normal recording. Click “None” in the drop-down menu to clear the selected schedule. Click “Apply” to save the settings.

If any changes need to be made, go to the “Edit Schedules” interface and click

to edit the

schedule. The settings of “Edit Schedule” are similar to that of the “Add Schedule”.

7.4 Record Mode
7.4.1 Manual Recording
Method One ­Manual record for all channels: Click on the tool bar at the bottom of the live-view interface to enable manual recording for all cameras. Method Two ­Manual record for single channel: In the live-view interface ­ either right click on the desired camera and choose “Manual Record On” or left click on the desired camera window and click on the channel tool bar.

Note: Click StartSettingsRecordMode Settings and set the manual record duration in the referred menu. Click “Apply” to save the settings. Default settings is “Manual”
7.4.2 Scheduled Recording:
Scheduled Recording: the system will record automatically according to the schedule weather there is an additional alarm or not. Set the record schedule of each camera – See 7.3 Schedule Setting for details.

7.4.3 Motion Based Recording:
The system will start recording based on motion alarms. You can use the default settings or create customized setting for each camera as follows: Set the motion alarm schedule for each camera. See 7.3 Schedule Setting for details. Enable the motion and set the motion area of each camera. See 9.2.1 Motion Configuration for details. The camera will start motion based recording as soon as the above settings are applied.

7.4.4 Sensor Based Recording:
The system will start recording based on sensor alarms. Configure the recording parameters as follows:

57

Record & Disk Management

User Manual

Set the sensor alarm schedule for each camera/alarm input. See 7.3 Schedule Setting for details. Set the NO/NC type of the sensor, enable the sensor alarm and check and configure the “Record”. See 9.1 Sensor Alarm for details.

7.4.5 Analytics Based Recording:
The system will start recording based on analytics alarms. Configure the recording parameters as follows: Set the analytics alarm schedule for each camera. See 7.3 Schedule Setting for details. Set each one of the available analytics alarms and check and configure the “Record”. See 9.1 Sensor Alarm for details.

7.5 Disk Management:
Click StartSettingsDiskDisk Management. On this interface you can view the device’s disk numbers, status and recording dates stored on each drive. Click “Format” button to format
the desired HDD or click on to format all drives together.

Note: 1. New HDD/s should be formatted before it can be used by the system. 2. If the HDD has been used in another device of the same model, please import the configuration file of the old device to the new device or format the HDD; if the models of the two devices are different, please format the HDD.
7.5.1 Storage Mode Configuration
Click StartSettingsDiskStorage Mode.

58

Record & Disk Management

User Manual

There are four available disk groups. By using disk group, you can allocate a specific camera to a specific disk (the recorded data from the grouped cameras will be stored in the disks allocated for that group).

Newly added disks and cameras will be joined into group one as default. The disks and

cameras in the different groups can be deleted except of group one (select a disk group and

click

on the top right corner of the added disk or camera to delete it from the group). The

deleted disks and cameras will be moved into group one automatically.

Each group can receive disks and cameras from other groups. Each disk/camera can be allocated to one group only.

Edit Disk/Camera Groups:

Select a disk group and click

in the disk or camera row to pop up a window. Check

the disks or cameras in the window and click “Add”.

Important: Changing group allocation for a disk/camera will result in losing data of the changed disk/camera.
7.5.2 Disk Mode (Models supporting RAID only):
Disk mode allows you to enable RAID (If supported by the device). Once the RAID is enabled, the device will reboot and new options will be available.
7.5.3 Physical Disk (Models supporting RAID only):
This menu is available only if RAID is enabled. Here you will see all the disks and their current status. Before you can start recording, you will need to assign the disks to RAID groups or assign it as “Hot Spare”.

Creating an array:
In order to assign disks, click on “Create Array”. The following window will appear. Set a name to the new array and choose the array type. The available options are RAID0, RAID1, RAID5, RAID6, RAID10. (For more information
59

Record & Disk Management

User Manual

about RAID types, please refer to appendix 2 at the end of the manual). Choose the disks that you want the array to include (Note that different RAID types require different number of disks. Click “Add” to finalize the process.

Notes: 1) All the data stored on the HDD will be deleted. 2) Up to 2 RAIDs can be configured.

Setting a “Hot Spare”
In terms of RAID, “Hot Spare” is a backup disk that is ready for use in case that an active array disk has failed. In such case, the hot spare will replace the failed array disk automatically and rebuilt its data (a process that takes time). The “Hot spare” of the system is global meaning that it will be used for all RAIDs configured on the system.
In order to assign a disk to perform as “Hot Spare”, click on the icon next to it and confirm the process. Repeat the process to change it back to normal state.

7.5.4 Array (Models supporting RAID only):
This menu is available only if RAID is enabled. Here you will see all the created RAID groups and their current status (Name, Capacity, Assigned Disks, Hot Spares, Status). Also, you will be able to delete the arrays and rebuilt it if required.

Rebuilding an array:
In case one of the disks of the array failed ­ the array state will change to “downgraded” and the rebuild button will become active as follows.

Once the faulty disk was replaced with a new one, click on the “rebuild” to restore the array state to normal.

Deleting an array: If you wish to delete an array, click on the

icon and confirm the process.

7.5.5 View Disk and S.M.A.R.T. Information:
Click StartSettingsDiskView Disk Information; click “S.M.A.R.T. Information” to view the working status of the HDD. Refer to the picture below.

60

Playback & Backup

User Manual

8 Search, Playback & Backup
8.1 Instant Playback
Click on the channel tool bar at the bottom of the live-view camera window to play back the record (click on the general tool bar at the bottom of the live- view interface to set the default playback time). Drag the playback progress bar to change the playback time. You can also click the right-click menu “Instant Playback” in the camera window and set the instant playback time to play back the record.

8.2 Playback Interface Introduction

Click

on the general tool bar at the bottom of the live-view interface or click

StartPlayback. (Click on the general tool bar at the bottom of the live-view interface to

set the default playback time).

61

Playback & Backup

User Manual

The interface will switch from live-view to playback and the cameras from the live-view will
be played back automatically. You can add the playback cameras manually by clicking on in the playback window to open the “Add Camera” window. Mark the cameras you wish to add and click “Add”. The system supports a maximum of 16 synchronous playback cameras.

The buttons of the general tool bar (area ) are introduced in the table below:

Button

Meaning

Start button. Click it to pop up area .

Full screen button. Click it to show full screen; click it again to exit the full screen.

Screen split modes.

/

“OSD ON/OFF” button. Click it to enable/disable the OSD

Stop button.

Rewind button. Click it to play video backward.

Play button. Click it to play video forward.

Pause button.

Decelerate button. Click it to decrease the playing speed.

Acceleration button. Click it to increase the playing speed.

Return to normal playback speed (x1)
Previous frame button. It works only when the forward playing is paused in single screen mode.
Next frame button. It works only when the forward playing is paused in single screen mode.

Click

to step backward 30s and click

to step forward 30s.

Enable/Disable Watermark appearance (Applicable for DVRs only)

Enable/Disable POS data appearance
Event list/tag button. Click it to view the event records of manual / schedule / sensor / motion and the tag information.
Backup button. Drag the mouse on the time scale to select the time periods and cameras and click the backup button to back up the record. (After marking the area for backup you can also click on the right mouse button)
View the backup status.

Back button. Click it to return.

Introduction of area :
Button

Meaning

Go to record search & backup interface; see 8.3 Record Search, Playback & Backup for details.

Click it to go to live-view interface; see Chapter 5 Live Preview Introduction for details.

62

Playback & Backup

User Manual

Click on the playback window to show the tool bar as shown in area ; right click on the

window to show the menu list. The tool bar and menu list are introduced in the table below.

Button

Menu List

Meaning

Move tool. Click it to move the tool bar.

Enable Audio Snap

Click it to enable audio and listen to the camera’s audio channel.
Click it to take a snapshot. Not supported by “X” models when playback is paused.

Zoom In

Click it to go to the digital zoom. The playback digital zoom interface is similar

to live-view digital zoom interface. Click

to pause the playback. When

the record is paused while in forward playing mode, you can click

to

view the previous frame and click

to view the next frame.

Fish Eye Add Tag Switch Camera Close Camera

Click it to open controls for Fish-Eye cameras as described in the “Live-View” Chapter.
Save a tag of the exact date and time you wish to save. You can use the tag later to go back quickly to the tagged point. When adding a new tag the system will name it with the saved time automatically. You can change the name or edit it later. Click it to switch the playback camera to a different camera that will playback the exact date and time. Click it and choose the new camera in the window. Click “OK” to change the camera.
Click it to close the playback camera.

Introduction of area :
Button

Meaning

Set/Change the playback date

Set/Change the playback time

**

Manual Record markings. Uncheck it to remove manual record display


Sensor Alarm Record markings. Uncheck it to remove manual record display Analytics Alarm Record markings. Uncheck it to remove manual record display Motion Alarm Record markings. Uncheck it to remove manual record display Schedule Record markings. Uncheck it to remove manual record display

**

POS Record markings. Uncheck it to remove manual record display

** Playback must be stopped completely before these icons can be used. After stopping the

playback use icon to add the desired cameras for search/playback.

63

Playback & Backup

User Manual

Introduction of the record time scale (area ):
Button

Meaning

The time-scale default view is 24 hours. Click on this icon to return to 24 hours view

/

Zoom in/out within the playback time scale

Move up the time scale (The mouse wheel can also be used)

Move down the time scale (The mouse wheel can also be used)

The record time scale shows different record types with different colors. The green color stands for manual record, red color stands for sensor alarm record, yellow color stands for motion alarm record and blue color stands for schedule record. Click the time scale to set the playback exact location. Drag the mouse cursor on the time scale to select the backup area and right click on the marked area or click to pop up a backup information window. Select the destination device, backup path and backup format and click “Backup” to start the backup process.
Introduction of “Smart Playback” (Area ):
Smart Playback allows you to perform simple analyzing of recorded video while playing it back, saving a lot of time and efforts.
The NSmotaer:t SpmlaayrbtacPklawybilalcdkisipslaayvaalillatbhleefiflotrerreedcroersduilntgs adnedvipcleasyriut nansiynoguOwsissiha. v1.3.x. All analog cameras are supported together with IPC running v4.2.1 or higher.

Button

Standard playback controls

Meaning

Smart playback controls

Full screen motion search Square selection motion search Line Crossing (Bi- Directional)

Polygon selection (up to 4 Corners)

Apply a face recognition filter (If applicable) Smart Search configuration.

If you wish to apply an additional face recognition filter to the smart search, click on the icon to open the filter interface.
64

Playback & Backup

User Manual

In the following interface tick “Enable face playback” in order to activate the face filter and set the similarity value.
You can choose face/faces from the following options: 1) Face database ­ Search from faces already in the database.
A) Here you can choose from the thumbnails or search by name. Click on “More” to narrow down groups or tick “All” to search/display within all groups.
B) Tick the face/faces you wish to search
for and click on Search by face/group as needed.

  1. Snapshot Gallery ­ Search within snapshots taken by the system A. Set the time range for the face snapshot search. (Day to choose a day, Week to choose a week, Month to choose a month, customization to set a unique time range and Today to choose the date of today starting at midnight). B. Choose the camera/cameras that took the face snapshot. Click on “More” to choose specific cameras or tick “All” to choose all cameras. C. Choose weather you like to see recognized and unrecognized faces in the search. D. Tick the face/faces you wish to search for and click on Search by face/group as needed.
  2. External Faces ­ Choose a picture file that contain a single face from a USB storage. A. Select the USB storage under the “Device Name” B. Select the relevant file (Must contain a single clear face). C. Click on Search face.
    Smart Search Settings: Click on the icon to open the settings menu: Here you can set if to skip unrequired video or play it. You can set the playback speed for required video and unrequired video (if requested), and set the intrusion percentage into the marked area in order to improve detection rate.
    65

Playback & Backup

User Manual

After applying smart playback filter you will see that the time bar will display the original time bar next to the filtered time bar as follows:
Full details

8.3 Record Search, Playback & Backup

Filtered details

8.3.1 Search & Playback by Time-sliced Image

Click StartSearch & BackupBy Time-sliced Image. The “Time-Sliced Image” search is designed to quickly find a small change in the scene that might have happened in a split of a second.

There are two view modes: by time and by camera. In the time view mode, a maximum of 64 camera thumbnails can be showed. If the camera thumbnail number is greater than 64, the cameras will be listed by their camera name, and not as a thumbnail. A maximum of 196 camera names can be listed. If the camera name number is more than 196, the time view mode will be disabled and only the camera view mode will be available. Double click on the selected camera or select one camera and click the “Open” button. The camera will refine from “Day” view to “Hour” view. Repeat this stage to refine from “Hour” view to “Minute” View. You can also click once on the thumbnail to commence playback on the left window. This will help you to confirm if you are in the right camera/time. Once in “Minute” view, double clicking on any image thumbnail will open the full playback interface and commence playback for the selected camera at the specific time and date. You can click once on the image box to play the record in the small playback box on the left side of the interface (If the thumbnail is blackened out ­ it means there is no record data available) You can perform backup directly from this interface in two methods:
A. Left click and drag the mouse on the time scale to select the segment for playback and click “Backup” button to continue; select the device, backup path and backup format in the opened window and click “Backup” button to start the backup.
B. After choosing the channel, click on “Set Backup Time” and input the start and end times. Confirm by clicking on “OK” and start the backup process using the “Backup” button.
66

Playback & Backup

User Manual

Click “Playback” button (Or double click on the thumbnail) to commence playback in the playback interface (refer to 8.2 Playback Interface Introduction for details). Click “Close” to close the interface.

Time Slice Mode Working method:

Method One: Click “Year”, “Month” or “Day” button under the record time scale to select the

time slice mode. In “Day” mode, click

/

on the left/right side of the time scale to

jump to the next/previous day; click “Minute” in the “Picture” option under the time scale to

select “Minute” mode (in “Minute” mode, click the time scale to change the time of the 60

display windows) and click “Hour” to select “Hour” mode.

Method Two: Click

beside “Camera Thumbnail” on the left top corner of the interface to

select the time slice mode.

Method Three: Right-click the mouse on any area of the time-sliced interface to go back to the

upper interface.

8.3.2 Search, Playback & Backup by Smart Search:
Click StartSearch & BackupSmart Search. Choose on the left pane the camera you wish to playback (Only one camera can be
selected) Smart Playback allows you to perform simple analyzing of recorded video while playing
it back, saving a lot of time and efforts.

Note: Smart search is available for recording devices running Ossia v1.3.x. All analog cameras are supported together with IPC running v4.2.1 or higher.

67

Playback & Backup

User Manual

Button

Full screen motion search

Meaning

Square selection motion search

Line Crossing (Bi-Directional)

Polygon selection (4 Corners) Smart Search configuration.

Face Recognition Filter (For applicable devices only)
Smart Search Settings: Click on the icon to open the settings menu: Here you can set the intrusion percentage into the marked area in order to improve detection rate.

8.3.3 Search, Playback & Backup by Time:

Click StartSearch & BackupBy Time.

Click

on the bottom of the interface to choose the cameras (A maximum of 16

cameras can be added). Click “Modify” on the top right corner of the camera window to

change the camera or click “Clear” to remove the camera.

Single click on the camera window to play the record in the small playback box on the left

side of the interface. You can set the date on the top left of the interface, check the event type as

required and click the time scale or click

under the time scale to set the time. The camera

window will play the record according to the time and event type you set. Single click on the time bar to set the time for playback. The camera thumbnails will be

68

Playback & Backup updated automatically and show a snapshot from the chosen time.

User Manual

You can perform backup directly from this interface. Left click and drag the mouse on the time scale to select the segment for playback and click “Backup” button to continue; select the device, backup path and backup format in the opened window and click “Backup” button to start the backup.
You can perform backup directly from this interface in two methods: a) Left click and drag the mouse on the time scale to select the segment for playback and click “Backup” button to continue; select the device, backup path and backup format in the opened window and click “Backup” button to start the backup. b) After choosing the channel, click on “Set Backup Time” and input the start and end times. Confirm by clicking on “OK” and start the backup process using the “Backup” button.
Click “Playback” button (Or double click on the thumbnail) to commence playback in the playback interface (refer to 8.2 Playback Interface Introduction for details). Click “Close” to close the interface.
8.3.4 Face Database Management
Click StartSearch & BackupFace Database.
69

Playback & Backup

User Manual

In This section you will be able to create, edit and manage your face database. By default, the database contains 3 groups:
a) Allow List1, Allow List2: Members of these groups are permitted 24/7
b) Block List: Members of this group are not permitted 24/7 You can create new groups by clicking on “Add Group”. You can configure “Permitted”
time for members of customized groups.

Click on to edit a group name and on cannot be deleted).

Click on

to open a group.

to delete a group (The default groups

Adding a new person to the database:

Click on “Add” to add a new person. The
following interface will open. Choose the source of the face snapshot. Snapshot
Gallery ­ Search within snapshots taken by the system or External Faces ­ Choose a picture
file that contain a single face from a USB
storage. Click on the “+” If you chose “Snapshot Gallery” the following
interface will open: A. Set the time range for the face
snapshot search. (Day to choose a day, Week to choose a week, Month to choose a month, customization to set a unique time range and Today to choose the date of today starting at midnight). B. Choose the camera/cameras that took the face snapshot. Click on “More” to choose specific cameras or tick “All” to choose all cameras. C. Click on “Search” D. Choose the face you wish to input to the database. Click on “OK” E. Fill the rest of the details in the form. (Only the name is mandatory. All the other fields are optional) External Faces ­ Choose a picture file that
contain a single face from a USB storage. A. Select the USB storage under the
“Device Name” B. Select the relevant file (Must contain a
single clear face). C. Click on Select face.

Note: that for good recognition results, the face must be well lit, looking straight to the camera with as many visible face features as possible (Eyes, pupils, ears, nose, mouth etc.)
70

Playback & Backup

User Manual

If you input a new person to a customized group, you will also have a validation period option meaning that the person will be recognized as permitted only within the specified time range.

Modifying a person in the database:

Click on

to open a group.

Select a person and click on “Modify” The person’s card will open. You will be able to edit any of the details and change the

assigned group of the person.

Deleting a person from the database:

Click on

to open a group.

Select a person and click on “Delete”

The system will prompt for deletion.

Clicking on “Clear All” will delete all the people in the specified group.

Exporting the database:

Click on Export and Import to open the
following interface. Click on “Export” to export the database. Set the
database name and target location. Set a password The database will be encrypted and exported to
the target location.

Exporting the database:

Click on Export and Import to open the
following interface. Choose the database file and click on “Import” Inpit the database password to initialize the import procedure The database will be created on the device. The device will reboot automatically at the end
of this procedure.

Note: the database is stored on the HDD. Formatting the HDD will delete the database as well. Importing a database will automatically overwrite the existing database.

71

Playback & Backup
8.3.5 Face Recognition Statistics
Click StartSearch & BackupFace Database. On the left pane, click on Statistics. The interface below will open.

User Manual

Choose the required groups and cameras. Set the time range for the statistics display. (Day to choose a day, Week to choose a week,
Month to choose a month, Quarter to choose a quarter, customization to set a unique time range and Today to choose the date of today starting at midnight).
8.3.6 Search, Backup & Playback by Event
Click StartSearch & BackupBy Event.
72

Playback & Backup

User Manual

Mark the required event type in the interface (Manual, Sensor, Motion or Analytics).

Click

to set the start time and end time on the top left of the interface.

Mark the desired cameras on the left side of the interface and click

to search the

database. The searched records will be displayed in the list.

Click

in the list to playback the record in a popup window. You can also select one

record data from the list and click “Backup” button instant backup. Select one record data from the list and click “Playback” button to play the record in the

playback interface.

8.3.7 Search & Playback by Tag
You have to save tags prior to using this interface. While playing back click on one of the camera windows to open the camera menu bar and click on . Click StartSearch & BackupTag Management

Click

in the interface to play the record. Click

to edit the tag name. Click

to

delete the tag.
8.3.8 Snapshots

Click StartSearch & BackupSnapshots. The system will display all the snapped images.

Click

to delete an image. Click

to open

the “Export” window. Select the device name and

save path in the window and click “Save” button.

Click

to open a view window. Click

to

export the image. Click

to view the previous

image or click

to view the next image. Click

to delete the image; click

to play all the

images automatically one by one.

73

Playback & Backup

User Manual

8.3.9 Backup Procedures
The recorded data and the snapped pictures can be backed up locally to USB (U-disk or external USB HDD) or by e-SATA (only available in selected models) it can also be backed up through network (only to AVI format). The file system of the backup devices must be FAT32 format or it will not be useable by the system. Refer to any of the Search & Backup methods and use the applicable backup methods. Once selecting the backup duration, click “Backup” button to open the “Record Backup” window as shown below. Select the device name, backup format and path and click “Backup” button to start the backup.

Note: There are two backup formats available: AVI is a common video file that can be played by any video player. “Private” format can be played by “RPAS player” only. The RPAS player will be added to on the USB device automatically.
8.3.10 View Backup Status
Click StartSearch & BackupBackup Status or click on the tool bar at the bottom of the playback interface to view the backup status. This will show all the active backup procedures. From here you will be able to see the general progress of the backup tasks and pause or delete any of it.

74

Account & Permission Management

User Manual

9 Alarm Management
9.1 Sensor Alarm
To fully configure the sensor alarm settings, you should enable the sensor alarm and set up the alarm handling for each camera/channel. Click StartSettingsAlarmSensor Alarm to access the following interface.

Select the alarm type (NO or NC) according to trigger type of the sensor. Enable the sensor alarm for the desired cameras/channels. Mark the and configure the desired response for sensor alarm out of “Record”, “Snap”, ,”Push Notification”, “Alarm-out” and “Preset”, and enable/disable “Buzzer”, “Pop-up Video”, “Pop-up Message Box” and “E-mail”. Click “Apply” to save the settings.

The configuration steps for the alarm responses are as follows: Record: once enabling “record” a “Trigger Record” window will pop up (you can also click “Configure” button to open the window manually). Select camera/s on the left side and click

to set the camera as a triggered camera. Select a triggered camera from the right side and

click

to remove the triggered camera. Click “OK” button to save the settings. The

triggered camera/s will commence recording in case of a sensor alarm. Snap: once enabling “Snap” a “Trigger Snapshot” window will pop up (you can also click “Configure” button to open the window manually). Select camera/s on the left side and click

to set the camera as a triggered camera. Select a triggered camera from the right side and

click

to remove the triggered camera. Click “OK” button to save the settings. The

triggered camera/s will take a snapshot in case of a sensor alarm.

Push: Tick if you wish to get push notifications for the selected input. Alarm-out: once enabling “Alarm-Out” a “Trigger alarm-out” window will pop up (you can also click “Configure” button to open the window manually). Select alarm/s on the left side and

click

to set the alarm as a triggered alarm. Select a triggered alarm from the right side

and click

to remove the triggered alarm. Click “OK” button to save the settings. The

triggered alarm will commence in case of a sensor alarm. You need to set the delay time and the

schedule of the alarm outputs. See 9.4.1 Alarm-out for details. Preset: once enabling “Preset” a “Trigger Preset” window will pop up. Configure the triggered preset of each PTZ camera. To add presets, please see 6.2 Preset Setting.

Buzzer: if enabled, the system will buzz using the internal buzzer when the sensor alarm is

75

Account & Permission Management

User Manual

triggered. To set the delay time of the buzzer, please see 9.4.4 Buzzer. Pop- up Video: once enabling “Pop-up Video” a “Set Camera” window will pop up. Select a camera from the list as the triggered channel. Click “OK” button to save the settings. The triggered camera will open in a single channel live- view in case of sensor alarm. To set the duration time of the video pop up, please see 9.4.3 Display. Pop-up Message Box: if enabled, the system will pop up the corresponding alarm message box automatically when a sensor alarm is triggered. To set the duration time of the message box, please see 9.4.3 Display. E-mail: if enabled, the system will send an e-mail when a sensor alarm is triggered. Before you enable the email, please configure the e-mail addresses first (see 11.1.4 E-mail Configuration).
9.2 Motion Alarm
Motion Alarm: when motion appears in the specified area, it will trigger the motion alarm. Remember that the motion alarm is based on VMD which translates pixel color changes as motion, therefore might trigger false alarms. You should enable and configure the motion detection for each of the cameras first and set the alarm handling to complete the motion alarm configuration.
9.2.1 Motion Configuration
Click StartSettingsCameraMotion to access the following interface.

Select the camera, enable the motion and set the sensitivity and duration of the alarm. Sensitivity: the higher the value is, the more sensitive it is to motion. You should adjust the value according to the practical conditions since the sensitivity is influenced by color and time (day or night).
76

Account & Permission Management

User Manual

Duration: it refers to the interval time between two motion detections. For instance, if the duration time is set to 10 seconds, once the system detects a motion, it will trigger the alarm and disregard all other motions for 10 seconds (specific to camera). If there is another motion detected during this period, it will be considered as continuous movement, otherwise it will be considered as a single motion.
To select the area of interest, click and drag the mouse cursor on camera image from the top left to the bottom right. You can set more than one motion area. Click “All” to set the whole camera image as the motion detection area. Click “Reverse” to swap the selected area and the unselected area. Click “Clear” to clear all the motion areas. To delete a specified area click and drag the mouse cursor on the camera image from the bottom right to the top left. Click “Apply” to save the settings. Click “Processing Mode” to go to the alarm handling configuration interface of the motion alarm.
9.2.2 Motion Alarm Handling Configuration
Click StartSettingsAlarmMotion Alarm to access the following interface.

Mark the and configure the desired response for motion alarm out of “Record”, “Snap”, “Push”, “Alarm-out” and “Preset”, and enable/disable “Buzzer”, “Pop-up Video”, “Pop-up Message Box” and “E-mail”. The alarm handling setting of motion alarm is similar to that of the sensor alarm (see 9.1 Sensor Alarm for details). Click “Apply” to save the settings. You can click “Motion Settings” to return to the motion configuration interface.
9.3 Analytics Configuration
In NVRs and Hybrid DVRs IP Channels, Analytics are applicable only when supported by the IPC. In DVRs running Ossia v1.3.x and up Sterile area and Line Crossing analytics are supported on analog cameras as well. Click StartSettingsCameraAnalytics to access the interface. There are several types of Analytics alarms. You will need to configure the ones that applies to your needs. Select the camera, and choose the type of analytics you wish to set.
Note: Camera Tampering can be enabled in all conditions, but only one of “Object Monitoring”, “Sterile area” “Line crossing” and “Face Detection” can be enabled in a given time.
77

Account & Permission Management

User Manual

9.3.1 Object Monitoring Configuration (IPC Channels Only)
Object monitoring will check that no items were left behind in a specified area (Left Object) or check that a monitored item was not taken (Missing Object)

Click StartSettingsAlarmAnalyticsObject monitoring (Must be supported by the IP Camera) to access the following interface.

Choose the camera. Enable/Disable the alarm. Set the Duration for detection (5sec-2mins) Choose the type of detection:
a) Missing object will monitor a specific object to prevent it from being taken. b) Left object will monitor an area to prevent from items to be left over. Set the warning area. Up to 4 areas can be configured. On the left side of the interface tick “Draw warning area” and create a polygon by clicking on the corners of the area you wish to mark. If you chose “missing object” then the polygon should be marked around a specific object. If you chose “left object” then the polygon should be marked around the monitored area. Set the area’s name. If you need to set additional areas, switch to area 2-4 and repeat stages 3-8
78

Account & Permission Management

User Manual

9.3.2 Camera Tampering Configuration (IPC Channels Only)
Camera tampering will check that the camera hasn’t been tampered in a way that will prevent it from providing a decent video image. The monitoring is divided into 3: 1) Camera Shifting: In case the camera was shifted and it does not point at the area that was
set during the installation. 2) Lens Tampering: In case the Zoom/Focus of the lens was tampered and the image became
blurry. 3) Camera Masking: In case that the camera was covered or blocked by a foreign object that
blocks the majority of its view.

Click StartSettingsAlarmAnalyticsCamera Tampering (Must be supported by the IP Camera) to access the following interface.

Choose the camera. Set the Duration for detection (5sec-2mins) Enable/Disable the required alarms. Set the sensitivity. If you need to set additional camera repeat stages 2-5
79

Account & Permission Management

User Manual

9.3.3 Line Crossing Configuration
Line crossing will detect any object that will fully cross a specified line. In Hybrid DVRs analog channels, the line crossing is only Bi-Directional (AB). Line crossing monitoring
generated by an IPC can work in 3 ways: 1) Left to Right (AB) 2) Right to Left (BA) 3) Any side to the other side (AB) Click StartSettingsAlarmAnalyticsLine Crossing (Must be supported by the
device) to access the following interface.

Choose the camera. Enable/Disable the alarm. Set the Duration for detection (5sec-2mins) Set the alert line. Up to 4 lines can be configured. On the left side of the interface tick “Draw line” and create line by clicking and dragging
the mouse cursor on the image. Set the detection direction as specified on the line. If you need to set additional lines, switch to line 2-4 and repeat stages 3-7
80

Account & Permission Management

User Manual

9.3.4 Sterile Area Configuration
Sterile area is an area which needs to be cleared from any object. Any object that will enter to the sterile area will trigger an alarm Click StartSettingsAlarmAnalyticsSterile Area (Must be supported by the device)
to access the following interface.

Choose the camera. Enable/Disable the alarm. Set the Duration for detection (5sec-2mins) Set the warning area. Up to 4 areas can be configured. On the left side of the interface tick “Draw warning area” and create a polygon by clicking
on the corners of the area you wish to mark. If you need to set additional areas, switch to area 2-4 and repeat stages 3-6
9.3.5 Analytics Alarm Handling Configuration
Click StartSettingsAlarmAnalytics Alarm to access the following interface.
81

Account & Permission Management

User Manual

Mark the and configure the desired response for each of the analytics alarm out of “Snap”, “Alarm-out” and “Preset”, and enable/disable “Buzzer”, “Pop-up Video”, “Pop-up Message Box” and “E-mail”. The alarm handling setting of analytics alarm is similar to that of the sensor alarm (see 9.1 Sensor Alarm for details). Click “Apply” to save the settings.

Note: You need to set the response for each of the analytics alarm separately. Failing to do so will result in insufficient system responses.

9.4 General Fault Alarms
9.4.1 General Fault Handling Settings
The system monitors its general health and the general condition of the HDD and network connection. The available alarms in this sector are: IP address conflict, Disk I/O error, Disk full, No disk, Illegal access, Network disconnected, HDD removed. Click StartSettingsAlarmGeneral Faults Handling Settings Mark the and configure the desired response for General fault alarms out of “Push” for push notification, “Alarm-out” for I/O output. Enable/disable “Buzzer”, “Pop-up Message Box” and “E-mail”. Click “Apply” to save the settings.

9.4.2 IPC Offline Settings
Click StartSettingsAlarmGeneral FaultsIPC Offline Settings to open the interface shown below.
Mark the and configure the desired response for IPC Offline Alarm out of “Push”, “Record”, “Snap”, “Alarm-out” and “Preset”, and enable/disable “Buzzer”, “Pop-up Video”, “Pop-up Message Box” and “E-mail”. The IPC Offline Settings are similar to that of the sensor
82

Account & Permission Management

User Manual

alarm (see 9.1 Sensor Alarm for details). Click “Apply” to save the settings.
9.5 Face Alarm
9.5.1 Face Detection
The system will trigger an alarm upon a detection of any face by the face detection cameras. Please note that the alarm is note relate to recognition, but to detection. Click StartSettingsAlarmFace AlarmFace Detection to open the interface shown below.

Mark the and configure the face detection desired response for each of the supporting channels out of “Push”, “Record”, “Snap”, “Alarm-out” and “Preset”, and enable/disable “Buzzer”, “Pop-up Video”
9.5.2 Face Match Parameters
The face match parameters is in direct relation with the next configuration ­ Face Match. It defines which cameras are allowed to trigger a response (Channel Settings) and under which condition (Similarity Settings. Click StartSettingsAlarmFace AlarmFace Match
Parameters to open the interface. Set the similarity settings. In this case, the similarity
settings mean that if the detection similarity is lower than the setting, the set action will not be triggers and vice versa. Set the Channel Settings. This defines which cameras are allowed to trigger a response in case of a recognition under the efficient similarity settings.
9.5.3 Face Match
The face match settings is the response for a face recognition under the settings of the “Face Match Parameters”. Click StartSettingsAlarmFace AlarmFace Match to open the interface.

83

Account & Permission Management

User Manual

Mark the and configure the response for each of the face database groups. Note that there is a “Stranger” group that is not defined in the database. All the unknown people falls into this group. The supported system responses are “Push”, “Record”, “Snap”, “Alarm-out” and “Preset”, and enable/disable “Buzzer”, “Pop-up Video”, “Pop up message” and “Send E-Mail”.
9.6 Alarm Event Notification
9.6.1 Alarm-out
Ossia devices will integrate with any device that has alarm output and display it on the alarm out list (together with any integral alarm outputs available on the device itself). Click StartSettingsAlarmAlarm Out to access the following interface.

Set the delay time and the schedule of each alarm-out. You access the “Edit Schedules” interface from here (see 7.3.1 Add Schedule for details). Click “Apply” to save the settings. You can click “Test” to test the alarm output.

9.6.2 E-mail
Click StartSettingsAlarmEvent NotificationE-mail to go to the e-mail configuration interface. See 11.1.4 E-mail Configuration for details.

9.6.3 Display

Click

StartSettingsAlarmEvent

NotificationDisplay to set the duration of the

pop-up video and pop-up message box. Click “Apply” to save the settings.

9.6.4 Buzzer

Click

StartSettingsAlarmEvent

NotificationBuzzer to set the holding time of the

buzzer and click “Apply” to save the setting. You can

click “Test” to test the buzzer.

84

Account & Permission Management

User Manual

9.6.5 Push Message
Click StartSettingsAlarmEvent NotificationPush Message. Enable the push message service and wait for the Push server status to change from “Disabled” to xxx.xxx.xxx.xxx:xxxx (Online). The IP Address of the Push server might vary according to your location and the availability of the server. All of the Push notification configuration will be done on your mobile phone through the “Provision Cam2” App. You can also set the “Push Schedule” which will define the days and times that push notifications will be sent by the device to the mobile app.
9.7 Manual Alarm
Click on the general tool bar at the bottom of the live-view interface to open the window as shown below. Click “Trigger” to start alarm. Click “Clear” to stop alarm. (The device must support alarms or have IPC which support alarm out connected to it in order to support this feature). If you wish for the alarm to be cleared automatically, set the delay timer according to your needs. “Manual” settings means that the alarm will stay active until you will clear it.

9.8 View Alarm Status
Click StartSettingsAlarmAlarm Status or click bottom of the live-view interface and click “Alarm Status”.

on the general tool bar at the

Click “Clear” button to stop the buzzer if the buzzer is on. Click information as shown below.
85

to view detailed

Account & Permission Management

User Manual

If the exception information is more than one page, you can input the number in the box and

click

to jump to the specified page. Click

/

to view the exception alarm

information in the previous/next pages. Click

to play the alarm record (if available).

86

Account & Permission Management

User Manual

10 Account & Permission Management
10.1 Account Management

Click StartSettingsAccount and AuthorityAccountEdit User
Area displays the user permissions. Area displays the user list. Click on a user in area to display its user permissions in area . There are three default permission groups (“Administrator”, “Advanced” and “Ordinary”) available when adding accounts. You can manually add new permission group (see 10.3.1 Add Permission Group for details). The user admin have all system permissions and it can manage the device’s accounts. Group “Administrator” owns all the permissions displayed in area and its permissions can never be changed or edited while the permissions of “Advanced” and “Ordinary” can be changed.

10.1.1 Add User

Click Start Settings Account and Authority

Account Add User or click

beside the search box.

Set the username, password and permission group. Try to choose a complicated password that will be hard to guess. It is optional to set the e-mail address and pattern lock. You can also set if the user is allowed to change his password. Click “Add” to confirm and add the user.

87

Account & Permission Management

User Manual

10.1.2 Edit User

Click StartSettingsAccount and AuthorityAccountEdit User. Click

in the user

list or double click the user to edit its information. Click admin cannot be deleted).

to delete the user (the user

Edit Security Question You can set password security question only for admin. Click “Edit Security Question” and set questions and answers in the opened window. If you forget the password, please refer to Q4 in Appendix A FAQ.
Modify Password Only

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals