JASCO 49789/49790 UltraPro Plug-In Single-Outlet Digital Timer Instruction Manual
- June 6, 2024
- JASCO
Table of Contents
49789 & 49790 PLUG-IN SINGLE-OUTLET
DIGITAL TIMER
Instruction Manual
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://byjasco.com/49789i
SETUP
-
If numbers are difficult to read or not visible on-screen, plug the timer into an outlet and let the timer charge for 1 hour. Once charged, press the reset ( ) button in the lower right corner using a toothpick or pencil.
Note: After the timer is charged, it can be removed from the outlet for easy programming. Return to the outlet when finished.
Note: When the timer is reset, the time will flash. -
Use up ( ) and down ( ) arrows to set current time. Take note of the AM/PM setting.
PROGRAMMING OPTIONS
DEFAULT TIMER
There
are two ON/OFF times available with preset default times. To activate default
times, simply press the ON TIME or OFF TIME button so the arrow ( ) next to
the button is visible on the display. To deactivate the default timer, press
and release the button. The arrow next to the button will disappear.
CUSTOMIZED TIMER
On time: Press and release either ON TIME button to enter custom setting
mode. The default on time flashes. Use arrow buttons ( ) to set the desired on
time. Press the ON TIME button or wait 5 seconds to set. If no button is
pressed within 5 seconds, the default timer will be set and the display will
return to clock mode. If you set the on-time earlier than the current time, it
will not turn on until the next day at the scheduled time.
Note: Mode indicator ( ) will move under SET while programming, then back
to CLOCK if it times out or after on time is set.
Off time: Press and release either OFF TIME button to enter custom
setting mode. The default off time flashes. Use arrow buttons ( ) to set the
desired off time. If no button is pressed within 5 seconds, the default timer
will be set and the display will return to clock mode. Press the OFF TIME
button or wait 5 seconds to set.
Note: When an on-time or off-time is set, the active program indicator ( )
will appear on the screen beside the button. Programs may run individually or
simultaneously.
ON/OFF OVERRIDE BUTTON/DOOR
Using ON/OFF override
with no scheduled programs:
– If the timer is off, press & release the ON/OFF override to turn the timer
on.
– If the timer is on, press & release the ON/OFF override to turn the timer
off.
Using the ON/OFF override with scheduled programs:
– If a scheduled program is running and the timer is on, press & release the
ON/OFF override to turn the timer off. It will remain off until the next
scheduled program turns the timer on.
– If a scheduled program is running and the timer is off, press & release the
ON/OFF override to turn the timer on. It will remain on until the next
scheduled program turns the timer off.
FCC/IC
Supplier Declaration of Conformity | Model #: 49789, 49790 | Jasco Products
Co., 10 E. Memorial Rd., Oklahoma City, OK 73114,
www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license-
exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
SPECIFICATIONS
125VAC, 60Hz
15A 1875W general/resistive
5A 625W tungsten
1/2HP motor
Works with dimmable LED and CFL bulbs
WARNING
RISK OF ELECTRICAL SHOCK
- PLUG DIRECTLY INTO AN ELECTRICAL OUTLET
- DO NOT USE IN WET LOCATIONS
- USE INDOORS ONLY
- UNPLUG TIMER BEFORE CLEANING
RISK OF FIRE
- DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN HEATING ELEMENTS (COOKING APPLIANCES, HEATERS, IRONS, ETC.)
- DO NOT EXCEED ELECTRICAL RATINGS
MADE IN CHINA/HECHO EN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City,
OK 73114.
This Jasco product comes with a 2-year limited warranty. Visit
www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483 between 7 AM-8 PM M-F,
Central Time.
©JASCO 2020 | 49789, 49790 | 09/03/20 v1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>