BORMANN PRO BVC6000 1600W Vacuum Cleaner User Manual
- June 3, 2024
- BORMANN
Table of Contents
BORMANN PRO BVC6000 1600W Vacuum Cleaner
SAFETY
Read the instructions carefully before using this device! Keep this manual in
a safe place for future reference. Read the Instruction carefully before
operation! Machine preparation, operation and maintenance of general safety
instructions are stated in the manual. When use must comply with the
instructions. If not
caused accidents, manufacturer will be not responsible for it.
- Don’t use inflammable liquids, gas, or with exposion-proof requirements region, protect from fire.
- Turn off the switch and take off plug before cleaning or repairing to avoid the risk of fire.
- The hose and the body may cause electrostatic, pay attention to this.
- Don’t trample, pulling folding hose, when hose is damaged do not continue use, don’ t use heavy or sharp blade pressure hose.
- Don’t let the power cord clap in the crack of the door or use cord pulling the vacuum cleaner, protect the cord.
- Protect own safety when using the device, keep the body away from the vacuum cleaner suction or activity parts.
- Avoid putting the whole machine in the water, don’t touch the plug with wet hands or wet towels, to prevent an electric shock.
- Voltage must be consistent with the power supply voltage, don’t use beyond the voltage range.
- Before water absorption, please remove the dust bags, filters, use the sponge filter.
- Keep clean when the tank have a lot of dust.
Warnings:
- Don’t let the glass, tack, iron and other sharp debris remaining in the hose, body, otherwise it will damage the hose, filter bag, etc.
- Don’t inhale hot, fire and caustic, flammable and explosive objects, avoid the risk from fire or electric shock.
- Suction of hair, paper, cement, slime, putty powder, sticky objects will easily block the vacuum, caused fire, do not use the device on these materials.
- Don’t use long time when the air inlet is blocked, otherwise will damage the vacuum.
- Stop using the device when abnormal sound, checking and clean.
- Please don’t let children use a vacuum cleaner accessories as a toy, in order to prevent the accident.
- Pull off the plug when not in use, in working status, do not leave.
- Do not keep the vacuum or cord near the hot sources, protect from fire.
- Do not use damaged cords and plugs, if broken, must be repaired by professionals.
Technical Data
- Voltage/Frequency: 220-240V/50Hz
- Power: 1600W
- Tank capacity/type: PP tank 30l
The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired. Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes. To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
Notice
The vacuum include double suction structure including front and upper suction,
can be used in different function.
Vacuum upper suction (picture A)
Hose connectors connect with upper suction, and use cap stem the front
suction.
Use front suctions when suction water (Picture B).
Hose connect with front suction, and cap stem the upper area.
Operating Instructions
-
Turn on or turn off (Picture 1)
-
Turning the device ON: After waiting for the power cord plug into the socket, press the switch button to 1 position, open the vacuum cleaner.
-
Turning off the device: Press the switch button to 0 position, close vacuum cleaner.
-
Hose connected to the vacuum cleaner (Picture 2)
Insert: Insert the hose joint aspiration in the mouth and the clockwise until the lock.
Pull: Holding the hose connector, counter-clockwise until the pull hose. -
Handle connect to take over pipe (Picture 3)
1. One side of the hose connect to the pipe, locking clockwise to tighten.
2. Hands hold interfaces to take over and handle respectively, reverse pull force. -
Take over to connect to the floor brush (Picture 4)
1. One side of pipe connect to the floor brush, locking, clockwise to tighten.
2. Hands holding interface to brush and take over to the counterclockwise direction until pull out. -
The front wheel installed (Picture 5)
1. Head and tank, after separation from the vacuum body parts (including universal wheel and rear wheel component).
2. Pull down the vacuum tank, insert two universal wheel base front on both sides of the hole. -
Power cord keeping (Picture 6)
1. The cable brackets are on the back of the vacuum, when do not use the machine, keep the cable on the brackets.
2. When use machine, take out the cable from brackets. -
Accessories storage (Figure 7)
1. Storage holes are on the 2 sides of machine, accessories can be put in. -
Blower function (Picture 8)
1. Insert the hose to the blowing part.
2. Use the hose blowing the area. -
Reverse wind function (Picture 9)
1. When the suction is lower, use the head of hose press the button.
2. Repeat press three to five times, increase the suction. -
Dust bag assemble (Picture 10)
1. Take off the transparent cover.
2. Install the dust bag on the cover, then assemble to the machine. -
Dust bag replacement (Picture 11)
1. Take off the transparent cover including the dust bag.
2. Use new dust bag instead of old one. -
Cover separate from tank (Picture 12)
1. Open the 2 side clamps
2. Holding the handle and take out the cover.
-
Filter replacement (Picture 13)
1. Take out the cover, the dirty filter is in the bottom, take out the filter.
2. Use a new filter instead of the old one, then assemble. -
Filter Clean (Picture 14)
1. Take out the filter and use clean water.
2. After clean, keep the filter dry, then reuse. -
Connectors clean (Picture 15)
1. Take off the connectors from the cover, use water clean.
2. Assemble the connectors and keep it tight. -
Adding water control (Picture 16)
1. Take off the cover from the vacuum body, pull water into the tank
2. Please note the ”water level”, avoid adding too much water. -
Speed controller operation (Picture 17)
1. The speed controller is placed above the switch.
2. Speed controller turn left, the suction turn down. Speed controller turn right, the suction turn up. -
Synchronous working with electric tool (Picture 18)
1. Connect the vacuum cleaner hose with dust absorption outlet of electric tool.
2. Put the power plug of the electric tool into the synchronization socket of the vacuum cleaner.
3. Switch turns to ”-” to stand by. Open the electric tool and then vacuum cleaner will start to work. -
Synchronous working with air tool (Picture 19)
1. Connect the vacuum cleaner’s hose with the dust absorption outlet of air tool.
2. Put the power plug of air tool into the gas seat valve of vacuum cleaner, and the other side of gas seat valve connects with air compressor.
3. Switch turns to ”-” to stand by. Open the electric tool and then vacuum cleaner will start to work.
Accessory instructions
Floor brush
Use for clean carpet, wood floor, marble floor, tile floor and so on.
Big nozzle
Use for clean corner of wall, winder and so on.
Big round brush
Use for cleaning the edges of sofa, furniture frame,etc.
Dust cleaning (Pictures 22 -23)
- Take off rear cover with dust bag form vacuum cleaner barrel.
- Take down the slip board below the dust bag, clean the dust.
- Fit on the slip board to dust bag, fix dust bag onto rear cover and put them back to barrel.
Emptying the dirty water from the barrel (Picture 24)
- Move vacuum cleaner near to sewers, take off the vacuum cleaner head.
- Incline vacuum cleaner barrel, clean the dirty water.
- Clean the dirty body with clean water, put the head back to barrel.
Maintenance
- In order to lengthen the life time, single using time is better not more than 20 minutes.
- In order to lengthen the life time, clean the body, filter and dust bag after use.
- Twine the power cord well, put accessories in slot.
- Clean the dirty water after using to prevent the rusting or corrosion of barrel.
- Clean the surface of vacuum cleaner with a dry cloth to prevent water getting into the vacuum cleaner and an electric short circuit even vacuum cleaner
burning.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>