WISILICA ACTWRT Control Motor Instructions
- June 13, 2024
- WISILICA
Table of Contents
ACTWRT Control Motor
Instructions
ACTWRT
Features
- 3.3VDC pulsed output to control motor
- BLE5.0 based non-flooding intelligent communication
- Compact form factor
- Zero downtime Over-the-Air (OTA) firmware updates
Specifications
Electrical| Symbol| Min.| Typ.| Max.| Unit|
Remarks
---|---|---|---|---|---|---
Input Voltage| Vin| 12| 12| 12| Vdc| Rated Input voltage
Input Current| Ian| | 10| 15| mA| @12 Vdc, Max RF transmitting
Pulsed Output| Symbol| Min.| Typ.| Max.| Unit|
Remarks
---|---|---|---|---|---|---
Output voltage| | 0| | 3.3| V| Max output tolerance ±5%
Output Current| | | | 15| mA|
Bluetooth| Symbol| Min.| Typ.| Max.| Unit|
Remarks
---|---|---|---|---|---|---
Frequency Range| | 2400| 2402| 2483.5| MHz|
Receiver Sensitivity| | -86| | -75| dBm|
Environmental| Symbol| Min.| Typ.| Max.| Unit| Remarks
---|---|---|---|---|---|---
Operating Temperature| ta| -20| | 50| ºC|
Storage Temperature| ts| -20| | 70| ºC|
Relative Humidity| | | | 85| %|
Mechanical| Symbol| Min.| Typ.| Max.| Unit|
Remarks
---|---|---|---|---|---|---
Dimensions| | | 66.7 x 29.2 x 22.4| | mm| L x W x H
Dimensions| | | 2.6 x 1.15 x 0.9| | inch| L x W x H
Net Weight| | | 40.0| | g| In gram
Net Weight| | | 1.41| | oz| In ounce
Device Dimensions
Case material: 5VA PC
Wire Description
| PIN | SYMBOL | COLOR | DESCRIPTION |
|---|---|---|---|
| 1 | CH1 | Green | 3.3V pulsed Output |
| 2 | GND | Blue | 12V Ground |
| 3 | 12V | Red | 12V Input |
Antenna Information
600mm wire antenna
Antenna Properties
Frequency range| 2.4 GHz-2.5GHz
Impedance| 50 Ω Nominal
VSWR| 1.92:1 Max
Return loss| -10 dB Max
Gain(peak)| 2 dBi
Cable loss| 0.3 dBi Max
Polarization| Linear vertical
Admitted power| 2 W
Wiring Diagram
Wiring ACTWRT to control motor
Warning
- To prevent the device from any defect, please handle and store it with care.
- Do not open or disassemble the product.
- Observe the correct polarity of output terminal
- Avoid input voltage exceeds the maximum rating, which will cause damage to the circuit and result in malfunction.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Version 1.0
****www.wisilica.com
[email protected]