RoHS Wifi Smart Switch User Guide

RoHS Wifi Smart Switch

User Guide

1. Start with “Smart Life”App.

2. Register an Smart Life Smart account.

3. IF you have Smart Life account, just log in.

4. Power up.
   ON/OFF operating principle: The connected appliances work/stop through live wire power on/off.

5. Appliance wiring instruction.

6. Celling lamp wiring instruction.

7. Light wiring instruction.

8. Press and hold the button for about 7 seconds until the WiFi green LED blinks fast.

9. Enter the App, tap “+”in the upper right of the page to enter network connection page.

10. There are two network connection methods (Normal mode and AP mode). Normal mode is default. Users could tap the upper right corner to switch the connection method to AP mode.

11. Please make sure the device’s indicator light rapidly flashes (2 times per second),tap to go on to the next step.

12. If indicator light is not rapidly flashing,tap “how to set indicator light as rapid flashes” to view operation processes.

13. Input your WiFi password.

14. Name your device.

15. The device is online.

TROUBLESHOOTING

Q: How to set indicator light as rapid flashing?

• Power on device.
• Hold the reset button for 5s.
• Confirm indicator light is now rapidly lashing.

Q: How to set indicator light as slow flashing?

• Power on device.
• Hold the reset button for 5s.
• Confirm in indicator light is now rapidly flashing.
• Hold reset button for 8s until indicator light is slowly flashing.
  The new added device needs 1min to connect to WiFi and the Internet if it stays offline for a long time, please judge the problem by the WiFi LED status.
  WiFi LED quickly blinks one time every second;

WiFi Switch failed to connect to your WiFi:

Maybe you have entered wrong WiFi password.
WiFi Switch is too far away from your WiFi please take it closer.
Make sure your router is MAC-open. If still failed, try to open a mobile hot a pot and add again.

Set your Echo speaker by Alexa APP

1. If you have finished to install Smart Life then open Amazon Alexa App; sign in your Alexa account and enter password.

2. Click the menu on the left corner-click “Settings”; choose “Set up a new device” (choose a device,like Echo) Note: When the below page appears, long press the small dot on your Echo device until the light turns to yellow. Then click Continue on App.
   Note: at this moment, the mobile phone can not open a variety of WPN software.

3. Choose your own WiFi and wait for a few minutes. After an introduction video. click next step, it will enter Home page automatically. Now the Echo has connected to Wi-Fi successfully.

Enable Smart Life Skill in Alexa APP

Choose “Skills” in the options bar, and then search “Smart Life” in the input box.

Select Smart Life in the search results, and then click “Enable Skill”.
Then input the user name and password of Smart Life APP that you had previously registered.

Control the Light Switch by Voice

After the above operation is successful, you can control the Light Switch via Echo.

1. Discover Devices
   Firstly, you need to say to the Echo: Echo (or Alexa), discover my devices. Echo will start to find the device which is added in Smart Life APP. It will take about 20 seconds, then Echo will tell you the result.
   You can also click “Discober devices” in Alexa APP, then it will show the devices that have been found successfully.

2. Control Device by Voice
   Note : The name of the device must be consistent with be addition of Smart Life APP.
   You can also group the Light Switch and give instructions to control them together. Note: Echo is one of the wake-up names, which can be any of the three names (Settings): Alexa, Echo, Amazon.

3. Support Skill List
   You can control the device by instructions like these:
   Alexa (or Echo), turn on the Light Switch Alexa (or Echo), turn off the Light Switch

Google Assistant – Activate Smart Life in Google Home App

Preparation

• Have downloaded the Google Home App-compatible with Android (4.2 or higher) or IOS (8.0 or higher) smartphones or tablet.
• Have registered your Google Account.
• Have paired Light Switch with Smart Life App and named it with a recognizable name.
• Have finished setting up Google Home.

STEP: 1 Open Google Home App; tap “ ”on the upper left corner; select “More Settings” to enter the next interface.

STEP:2 Choose “Services” in the opptions bar and select “Smart Life”to enter the next interface.

STEP:3 Tap “Link Account”, then sign in your Smart Life Account.

STEP:3 Tap “Link Now”, after your Smart Life account has linked to Google Assistant, the smart devices will automatically appear.

Command the Device through Your Voice After the above operation is successful, you can control the device via Google Home. Firstly, you need to say “OK Google, talk to Smart Life” to wake up the Smart Life. Then you can control the device by instructions like these:

IFTTT-Setup and Usage

Get Started: How to connect the product to IFTTT?

STEP:1 Visit the IFTTT official website on your PC and sign in with your IFTTT account. Note: You can also use IFTTT app and follow similar steps to connect your device to the IFTTT. In this FAQ we take the website setting method for example.
STEP:2 Search for “Smart Life”, and then click “Smart Life” service.
STEP:3 Click “Connect”, then log in your Smart Life ID and tap “Link Now”. (The Smart Life ID is the same with that of Smart Life APP).

STEP:4 After successfully connecting your IFTTT account to your Smart Life ID. You are ready to enjoy the IFTTT service of the product now.

Instructions:2 methods to use IFTTT with the products.
Method 1 On Smart Life service page, choose an existing Applet you need,turn it on and then finish the configuration.
Method 2 Create a new Applet on your own.
Click “My Applet” on the top and then click “New Applet” on the right top corner of the webpage to create a new Applet.

STEP:1 Create a Trigger Tap “this” to choose a Trigger. You can search for “Weather Underground” to choose a Trigger.
STEP:2 Create an Action Tap “that” to choose an Action. You can search for “Smart Life”to choose a Smart Life Action.
STEP:3 We select “Turn on ”of the Light Switch as the Action in this case. New Applet “If sunset, then turn on Light Switch”has created as a result.
Note:
The Smart Life service can only work when creating an action. You can’t use “Smart Life”as a trigger.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>