watchgas SST Dock-QSG-V1.1 Automated Test Station Bump User Guide

SST Dock-QSG-V1.1 Automated Test Station Bump

Specifications

• Model: SST Dock
• Version: 1.1
• Language: English
• Release Date: 09-07-24

Product Usage Instructions

Prepare for Use

Ensure the SST Dock is properly connected and attached to a
venting system or used in a well-ventilated area.

Introduction

The SST Dock is an automated test station designed for Bump and
Calibration testing. It is compatible with the full SST-Range in
one module and can be connected via Wi-Fi, BLE, or Cellular. The
dock allows for desk, wall, and hard case mounting based on your
application needs. It features two inlets for calibration of
standard four gases plus an additional gas type. The built-in NFC
simplifies assigning gas cylinders to the correct ports.

SST Dock Overview

• Touch Screen
• Status LED
• Bottle NFC Reader
• Lid Lock
• Mounting Bracket
• Exhaust Outlet
• Gas Inlet 1 & 2
• Pressure Sensor Connectors
• Fresh Air Inlet Filter
• Fresh Air Inlet Pressure Sensor
• On/Off Key

Mounting the SST Dock

The SST Dock can be mounted on a wall or table using the
provided brackets. Ensure to use the correct mounting hardware and
seek assistance from a qualified installation contractor for proper
installation.

Switch On the SST Dock

If the SST Dock is fully discharged, charge it for at least 1
hour before switching it on. Connect the dock to an electrical
outlet using the included power adapter. Power on the touch screen
using the ON/OFF key.

Enter Setup

1. Use the password “user” or “service” to access the setup
   menu.

2. Activate optional pressure sensors if used to avoid signal
   ignorance by the SST Dock.

3. Add calibration gas bottles to the list and assign them to the
   input ports selected.

4. Monitor the status LED for operational indications.

FAQ

Q: What should I do if the SST Dock does not power on?

A: Make sure it is adequately charged and connected to a power
source. Press the ON/OFF key to power it on.

Q: Can I mount the SST Dock without professional

assistance?

A: It is recommended to seek help from a qualified installation
contractor for mounting the SST Dock to ensure proper installation
and safety.

SST Dock
Quick Start Guide
SST Dock | QSG | V 1.1 | EN | 09-07-24

CAUTIONS & BEST PRACTICES
· If the SST Dock appears to be damaged or is not functioning properly, please contact WatchGas or a local WatchGas distributor;
· SST Dock uses Calibration Gas to carry out testing and calibrations so always ensure that these tests are done in a well-ventilated area;
· · Avoid the station encountering liquids. SST Dock cannot be mounted in an outside location that could be
exposed to rain or wet conditions; · Maximum exhaust tubing length is 10 meters (30 feet); · · SST Dock has no hazardous location approvals and can only be used in a safe and non-hazardous
· · Ensure calibration gas cylinders are the correct concentration, within their expiration date and contain gas; · Warranty does not cover electrical surges, physical and/or water damages.

WARNING IMPORTANT SAFETY INFORMATION: READ BEFORE USE

· To ensure personal safety, read Safety Information and Warnings before using the SST DOCK.

·

by the SST DOCK. The safety and security of any system or network incorporating the SST DOCK and its

accessory components is the responsibility of the assembler of the system.

· Follow all required National Electric Codes (NEC) and safety codes.

· Do not attempt to adjust, disassemble, or service the equipment.

· Only use in a well-ventilated space, in normal atmosphere, 20.9% Oxygen and non-hazardous environment.

· Only use the supplied charging adapter, 12V 1.5A.

·

a

2

PREPARE FOR USE
· Use only Luer PG-63 for all gas inlets/outlets. · Tubing diameter no less than 3mm (1/8 in) internal diameter. The tubing should be suitable for
the gas used, consult WatchGas for proper Last-o-more tube or compatible tube. ·
NOTE: only connect up to 10 meter (30 feet) of tubing on the fresh air inlet and outlet. · Ventilation ­ the outlet should be routed to a ventilated area. · Adjust the fresh air purge time accordingly. · Ensure tubing and cables are proper installed. · Use the shortest lenght of tubing possible. · · If potentially harmful gas is used for calibrations, users must read the MSDS of the gas
connected. The SST DOCK must be attached to a venting system or be used in a well-ventilated area.
3

INTRODUCTION

The SST Dock is an automated test station that allows Bump and Calibration testing. It is compat ible with the full SST-Range in one module. It has the capabilities to be connected via Wi-Fi, BLE or Cellular and allows for desk, wall and hard case mounted dependent on your application. With two inlets it allows for calibration of the standard four gases plus another gas type. With built-in NFC it is easier than ever to assign gas cylinders to the correct gas in ports.

SST DOCK OVERVIEW

1. Touch Screen

2. Touch Screen ON/OFF

4

3. Status LED

3 16

4. Instruction Label

7

5. Bottle NFC Reader

11

6. Lid Lock 7. 12V Power Connection

2

9 13

8. Mounting Bracket

9. Exhaust Outlet

1

10

10. Gas Inlet 2

12

11. Gas Inlet 2 Pressure Sensor Connector

12. Gas Inlet 1

13. Gas Inlet 1 Pressure Sensor Connector

Fresh Air Inlet Filter

5

6

15

14 8

15. Fresh Air Inlet Pressure Sensor 16. On / Off Key

Figure 1.

4

MOUNTING THE SST DOCK
The SST DOCK can be mounted with the invertable mounting bracket in 2 di erent angels. Use the extended screws and plastic spacer included in the box.
Wall mounting The provided mounting brackets can be used to mount the SST Dock to a wall or table. Mounting screws and plug are not provided. WatchGas recommends to check the strength of the mounting area and to select the proper mounting hardware before mounting the SST Dock. Mounting the SST Dock should be performed by a qualified installation contractor.

SST Dock on a wall

SST Dock on a table

Installing the brackets

SWITCH ON THE SST DOCK

If the SST DOCK is fully discharged, please allow for 1 hour of charging prior to switching on the unit.

LED will show red switching to white prior to start-up.

Connect the SST DOCK to an electrical outlet (or surge protector) by means of the included power

adapter. The status light will then turn on. Use the ON / OFF key (fig 1. part 16 and part 2) to power

on the touch screen.

5

ENTER SET UP
1. Use the password “user” or “service” 2. to enter the setup menu.
IMPORTANT: If optional pressure sensors are utilized these shall be activated or the SST DOCK will ignore the signal. You can set this up in SST DOCK Setting -> Settings, with the Pressure sensor fitted option.

Add calibration gas bottle in the Gas bottle

list either manual or utilize Watch Tab enabled

`s

,

Enter the password

Pressure sensor fitted

Bump & Calibration

To add a new Calibration bottle click “Add bottle”.
6

3. Assign the gas cylinder to the input port selected (the input will light up when the port is open during operation). NOTE: The SST DOCK will not perform any bump or calibration if the gas does not match the detector target gas.
4. Status LED Green normal operation and on charge / yellow running on battery / RED fault.
5. Server setup ­ linking to the WatchGas compliance software the server ID must be set up. This link will be provided upon purchase of the software.

USE
The screen will instruct the next step. If there is a fault with the SST Dock, this will be indicated with a red-colored Dock Fault at the bottom of the screen. Press this red banner to remove the fault.

WatchGas App home screen

Press Dock Fault

to remove fault

7

INSERTING THE DETECTOR

ACTION WHEN LID CLOSED

Step 1 Power on the gas detector if required. Turn on NFC.
Step 2 Lift the lid on the SST Dock by using the two finger guides and the red latch.
Step 3 Insert device by locating the alligator clip into the guide in the SST Dock.
Step 4 Close the Lid until you hear the click.
Step 5 Select the function on the SST Dock Display that you want to carry out, bump test, calibration, or fresh air calibration. The SST Dock will then carry out the selected test.

From the main menu, navigate to SST Dock Setting and select Settings. You can set up what the SST Dock is going to automatically do to the device inside once you close the lid. The following actions are available:
· Always ask (open dialog with calibration, bump, and zero)
· Fresh air calibration · Bump · Calibration

8

SST DOCK WIFI
From the main menu, select Wi-Fi settings. This is where you can choose which Wi-Fi network to connect to.

SST DOCK EXIT KIOSK
To exit the Kiosk mode on your SST Dock, select Exit Kiosk mode from the main menu. Enter password “2017” and press Enter.

9

SPECIFICATIONS

Dimensions (LxWxH) Weight Operating Temperature Humidity Storage Temperature
Power Supply

28 x 21 x 10 cm / 11.5 x 8.5 x 4.5 in

1.8 kg / 4 lbs

+5-40 °C / 40-104°F

10% to 90% RH

0-50 °C / 32-120°F

12 V

1.5 A

L.P.S.

Real Time Clock Data Storage Connection capability Gas Inlets

Yes, updateable More than 1 year of operation Wi-Fi, Cellular, BLE ­ Connected into the Cloud and WatchGas App Fresh air inlet, 2 Gas inlets and one purge

Testing Function
Device Compatibility Warranty

Download. Also tests device Alarms, Visual LED’s and Vibrator One module compatible with SST Range 2 Year warranty

10

WARNING
MAINTENANCE
Periodically check that the inlet filter is free of dirt and replace it if required. The SST Dock can be can be cleaned with a soft, damp cloth. Do not use solvents, soaps, polishes, or immerse the SST Dock in liquids. Completely turn o the unit and disconnect the power supply before cleaning.
11

WARNING ONLY USE ORIGINAL WATCHGAS PARTS AND / OR ACCESSORIES
PARTS AND ACCESSORIES
Serviceable parts and accessories are sold separately. Please contact WatchGas or an authorized distributor, or visit the website at www.watchgas.com or www.watchgasusa.com if in North America. Parts list · WatchGas Demand Flow Regulator (PN: DFR-SS) · WatchGas Demand Flow Regulator including pressure sensor (PN: DFR-PSV) · PG-63 Luer (PN: SST-DOCK-LUR) · Tubing · Mounting brackets, spacers and screws (PN: SST-DOCK-MB)
12

TROUBLESHOOTING
Detector fails bump, fresh air, or calibration: 1. 2. Check that gas bottles are connected, sufficiently pressurized, and contain the right gas
concentration (information on the bottle). 3. Verify the station function with a known functional detector. Detector fails alarm test: 1. Redo the test. 2. Manually inspect the detector for LED, vibration and audio alarms. 3. Test a known fully functional detector in the station to verify station function. Station fail: 1. Clear fault and retry. 2. Contact service representative.
13

CONTACT INFORMATION
EMEA
Klaverbaan 121, 2908 KD, Capelle a/d IJssel,
the Netherlands info@watchgas.com www.watchgas.com
Americas
313 N. State Hwy 342 Red Oak, TX 75154, USA info@watchgasusa.com www.watchgasusa.com
APAC
Woods Square Tower 1, 12 Woodlands Square, #11-71, Singapore 737715
ANZ
aus@watchgas.com
SST Dock | QSG | V 1.1 | EN | 09-07-24 © 2024 WatchGas B.V. WatchGas is dedicated to continuously improving its products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>